Skip to content
The Chat Archive
gpt-4-0125-preview· OpenAI WildChat-4.8M (AI2)

Please write the appropriate code in "FILL YOUR CODE HERE".…

  1. User

    Please write the appropriate code in "FILL YOUR CODE HERE".

    <StartOfFile:DMAC/RTL/DMAC_CFG.sv>> module DMAC_CFG ( input wire clk, input wire rst_n, // _n means active low

    // AMBA APB interface
    input wire psel_i,
    input wire penable_i,
    input wire [11:0] paddr_i,
    input wire pwrite_i,
    input wire [31:0] pwdata_i,
    output reg pready_o,
    output reg [31:0] prdata_o,
    output reg pslverr_o,
    
    // configuration registers
    output reg [31:0] src_addr_o,
    output reg [31:0] dst_addr_o,
    output reg [15:0] byte_len_o,
    output wire start_o,
    input wire done_i
    

    );

    // Configuration register to read/write
    reg [31:0] src_addr;
    reg [31:0] dst_addr;
    reg [15:0] byte_len;
    
    //----------------------------------------------------------
    // Write
    //----------------------------------------------------------
    // an APB write occurs when PSEL & PENABLE & PWRITE
    // clk : __--__--__--__--__--__--__--__--__--__--
    // psel : ___--------_____________________________
    // penable : _______----_____________________________
    // pwrite : ___--------_____________________________
    // wren : _______----_____________________________
    //
    // DMA start command must be asserted when APB writes 1 to the DMA_CMD
    // register
    // clk : __--__--__--__--__--__--__--__--__--__--
    // psel : ___--------_____________________________
    // penable : _______----_____________________________
    // pwrite : ___--------_____________________________
    // paddr : |DMA_CMD|
    // pwdata : | 1 |
    // start : _______----_____________________________
    
    wire wren = psel_i & penable_i & pwrite_i;
    
    always @(posedge clk) begin
        if (!rst_n) begin
            src_addr <= 32'd0;
            dst_addr <= 32'd0;
            byte_len <= 16'd0;
        end
        else if (wren) begin
            case (paddr_i)
                'h100: src_addr <= pwdata_i[31:0];
                'h104: dst_addr <= pwdata_i[31:0];
                'h108: byte_len <= pwdata_i[15:0];
            endcase
        end
    end
    wire start = wren & (paddr_i=='h10C) & pwdata_i[0];
    
    //----------------------------------------------------------
    // READ
    //----------------------------------------------------------
    // an APB read occurs when PSEL & PENABLE & !PWRITE
    // To make read data a direct output from register,
    // this code shall buffer the muxed read data into a register
    // in the SETUP cycle (PSEL & !PENABLE)
    // clk : __--__--__--__--__--__--__--__--__--__--
    // psel : ___--------_____________________________
    // penable : _______----_____________________________
    // pwrite : ________________________________________
    // reg update : ___----_________________________________
    // prdata : |DATA
    
    reg [31:0] rdata;
    
    always @(posedge clk) begin
        if (!rst_n) begin
            rdata <= 32'd0;
        end
        else if (psel_i & !penable_i & !pwrite_i) begin // in the setup cycle in the APB state diagram
            case (paddr_i)
                'h0: rdata <= 32'h0001_2024;
                'h100: rdata <= src_addr;
                'h104: rdata <= dst_addr;
                'h108: rdata <= {16'd0, byte_len};
                'h110: rdata <= {31'd0, done_i};
                default: rdata <= 32'd0;
            endcase
        end
    end
    
    // output assignments
    assign pready_o = 1'b1;
    assign prdata_o = rdata;
    assign pslverr_o = 1'b0;
    
    assign src_addr_o = src_addr;
    assign dst_addr_o = dst_addr;
    assign byte_len_o = byte_len;
    assign start_o = start;
    

    endmodule <<EndOfFile:DMAC/RTL/DMAC_CFG.sv>>

    <<StartOfFile:DMAC/RTL/DMAC_ENGINE.sv>> module DMAC_ENGINE ( input wire clk, input wire rst_n, // _n means active low

    // configuration registers
    input wire [31:0] src_addr_i,
    input wire [31:0] dst_addr_i,
    input wire [15:0] byte_len_i,
    input wire start_i,
    output wire done_o,
    
    // AMBA AXI interface (AW channel)
    output wire [3:0] awid_o,
    output wire [31:0] awaddr_o,
    output wire [3:0] awlen_o,
    output wire [2:0] awsize_o,
    output wire [1:0] awburst_o,
    output wire awvalid_o,
    input wire awready_i,
    
    // AMBA AXI interface (W channel)
    output wire [3:0] wid_o,
    output wire [31:0] wdata_o,
    output wire [3:0] wstrb_o,
    output wire wlast_o,
    output wire wvalid_o,
    input wire wready_i,
    
    // AMBA AXI interface (B channel)
    input wire [3:0] bid_i,
    input wire [1:0] bresp_i,
    input wire bvalid_i,
    output wire bready_o,
    
    // AMBA AXI interface (AR channel)
    output wire [3:0] arid_o,
    output wire [31:0] araddr_o,
    output wire [3:0] arlen_o,
    output wire [2:0] arsize_o,
    output wire [1:0] arburst_o,
    output wire arvalid_o,
    input wire arready_i,
    
    // AMBA AXI interface (R channel)
    input wire [3:0] rid_i,
    input wire [31:0] rdata_i,
    input wire [1:0] rresp_i,
    input wire rlast_i,
    input wire rvalid_i,
    output wire rready_o
    

    );

    // mnemonics for state values
    localparam S_IDLE = 3'd0,
                                S_RREQ = 3'd1,
                                S_RDATA = 3'd2,
                                S_WREQ = 3'd3,
                                S_WDATA = 3'd4;
    
    reg [2:0] state, state_n;
    
    reg [31:0] src_addr, src_addr_n;
    reg [31:0] dst_addr, dst_addr_n;
    reg [15:0] cnt, cnt_n;
    reg [3:0] wcnt, wcnt_n;
    
    reg arvalid,
                                rready,
                                awvalid,
                                wvalid,
                                wlast,
                                done;
    
    wire fifo_full,
                                fifo_empty;
    reg fifo_wren,
                                fifo_rden;
    wire [31:0] fifo_rdata;
    
    
    // it's desirable to code registers in a simple way
    always_ff @(posedge clk)
        if (!rst_n) begin
            state <= S_IDLE;
    
            src_addr <= 32'd0;
            dst_addr <= 32'd0;
            cnt <= 16'd0;
    
            wcnt <= 4'd0;
        end
        else begin
            state <= state_n;
    
            src_addr <= src_addr_n;
            dst_addr <= dst_addr_n;
            cnt <= cnt_n;
    
            wcnt <= wcnt_n;
        end
    
    
    // this block programs output values and next register values
    // based on states.
    always_comb begin
        // ********************** 
        // ********************** 
        // FILL YOUR CODE HERE
        // ********************** 
        // ********************** 
    end
    
    DMAC_FIFO u_fifo
    (
        .clk (clk),
        .rst_n (rst_n),
    
        .full_o (fifo_full),
        .wren_i (fifo_wren),
        .wdata_i (rdata_i),
    
        .empty_o (fifo_empty),
        .rden_i (fifo_rden),
        .rdata_o (fifo_rdata)
    );
    
    // Output assigments
    assign done_o = done;
    
    assign awid_o = 4'd0;
    assign awaddr_o = dst_addr;
    assign awlen_o = (cnt >= 'd64) ? 4'hF: cnt[5:2]-4'h1;
    assign awsize_o = 3'b010; // 4 bytes per transfer
    assign awburst_o = 2'b01; // incremental
    assign awvalid_o = awvalid;
    
    assign wid_o = 4'd0;
    assign wdata_o = fifo_rdata;
    assign wstrb_o = 4'b1111; // all bytes within 4 byte are valid
    assign wlast_o = wlast;
    assign wvalid_o = wvalid;
    
    assign bready_o = 1'b1;
    
    assign arvalid_o = arvalid;
    assign araddr_o = src_addr;
    assign arid_o = 4'd0;
    assign arlen_o = (cnt >= 'd64) ? 4'hF: cnt[5:2]-4'h1;
    assign arsize_o = 3'b010; // 4 bytes per transfer
    assign arburst_o = 2'b01; // incremental
    assign arvalid_o = arvalid;
    
    assign rready_o = rready & !fifo_full;
    

    endmodule <<EndOfFile:DMAC/RTL/DMAC_ENGINE.sv>>

    <<StartOfFile:DMAC/RTL/DMAC_FIFO.sv>> module DMAC_FIFO #( parameter DEPTH_LG2 = 4, parameter DATA_WIDTH = 32 ) ( input wire clk, input wire rst_n,

    output wire full_o,
    input wire wren_i,
    input wire [DATA_WIDTH-1:0] wdata_i,
    
    output wire empty_o,
    input wire rden_i,
    output wire [DATA_WIDTH-1:0] rdata_o
    

    );

    localparam FIFO_DEPTH = (1<<DEPTH_LG2);
    
    reg [DATA_WIDTH-1:0] data[FIFO_DEPTH];
    
    reg full, full_n,
                                        empty, empty_n;
    reg [DEPTH_LG2:0] wrptr, wrptr_n,
                                        rdptr, rdptr_n;
    
    // reset entries to all 0s
    always_ff @(posedge clk)
        if (!rst_n) begin
            full <= 1'b0;
            empty <= 1'b1; // empty after as reset
    
            wrptr <= {(DEPTH_LG2+1){1'b0}};
            rdptr <= {(DEPTH_LG2+1){1'b0}};
    
            for (int i=0; i<FIFO_DEPTH; i++) begin
                data[i] <= {DATA_WIDTH{1'b0}};
            end
        end
        else begin
            full <= full_n;
            empty <= empty_n;
    
            wrptr <= wrptr_n;
            rdptr <= rdptr_n;
    
            if (wren_i) begin
                data[wrptr[DEPTH_LG2-1:0]] <= wdata_i;
            end
        end
    
    always_comb begin
        wrptr_n = wrptr;
        rdptr_n = rdptr;
    
        if (wren_i) begin
            wrptr_n = wrptr + 'd1;
        end
    
        if (rden_i) begin
            rdptr_n = rdptr + 'd1;
        end
    
        empty_n = (wrptr_n == rdptr_n);
        full_n = (wrptr_n[DEPTH_LG2]!=rdptr_n[DEPTH_LG2])
                                     &(wrptr_n[DEPTH_LG2-1:0]==rdptr_n[DEPTH_LG2-1:0]);
    
    end
    
    // synthesis translate_off
    always @(posedge clk) begin
        if (full_o & wren_i) begin
            \$display("FIFO overflow");
            @(posedge clk);
            \$finish;
        end
    end
    
    always @(posedge clk) begin
        if (empty_o & rden_i) begin
            \$display("FIFO underflow");
            @(posedge clk);
            \$finish;
        end
    end
    // synthesis translate_on
    
    assign full_o = full;
    assign empty_o = empty;
    assign rdata_o = data[rdptr[DEPTH_LG2-1:0]];
    

    endmodule <<EndOfFile:DMAC/RTL/DMAC_FIFO.sv>>

    <<StartOfFile:DMAC/RTL/DMAC_TOP.sv>>

    module DMAC_TOP ( input wire clk, input wire rst_n, // _n means active low

    // AMBA APB interface
    input wire psel_i,
    input wire penable_i,
    input wire [11:0] paddr_i,
    input wire pwrite_i,
    input wire [31:0] pwdata_i,
    output reg pready_o,
    output reg [31:0] prdata_o,
    output reg pslverr_o,
    
    // AMBA AXI interface (AW channel)
    output wire [3:0] awid_o,
    output wire [31:0] awaddr_o,
    output wire [3:0] awlen_o,
    output wire [2:0] awsize_o,
    output wire [1:0] awburst_o,
    output wire awvalid_o,
    input wire awready_i,
    
    // AMBA AXI interface (AW channel)
    output wire [3:0] wid_o,
    output wire [31:0] wdata_o,
    output wire [3:0] wstrb_o,
    output wire wlast_o,
    output wire wvalid_o,
    input wire wready_i,
    
    // AMBA AXI interface (B channel)
    input wire [3:0] bid_i,
    input wire [1:0] bresp_i,
    input wire bvalid_i,
    output wire bready_o,
    
    // AMBA AXI interface (AR channel)
    output wire [3:0] arid_o,
    output wire [31:0] araddr_o,
    output wire [3:0] arlen_o,
    output wire [2:0] arsize_o,
    output wire [1:0] arburst_o,
    output wire arvalid_o,
    input wire arready_i,
    
    // AMBA AXI interface (R channel)
    input wire [3:0] rid_i,
    input wire [31:0] rdata_i,
    input wire [1:0] rresp_i,
    input wire rlast_i,
    input wire rvalid_i,
    output wire rready_o
    

    );

    wire [31:0] src_addr;
    wire [31:0] dst_addr;
    wire [15:0] byte_len;
    wire start;
    wire done;
    
    DMAC_CFG u_cfg(
        .clk (clk),
        .rst_n (rst_n),
    
        // AMBA APB interface
        .psel_i (psel_i),
        .penable_i (penable_i),
        .paddr_i (paddr_i),
        .pwrite_i (pwrite_i),
        .pwdata_i (pwdata_i),
        .pready_o (pready_o),
        .prdata_o (prdata_o),
        .pslverr_o (pslverr_o),
    
        .src_addr_o (src_addr),
        .dst_addr_o (dst_addr),
        .byte_len_o (byte_len),
        .start_o (start),
        .done_i (done)
    );
    
    DMAC_ENGINE u_engine(
        .clk (clk),
        .rst_n (rst_n),
    
        // configuration registers
        .src_addr_i (src_addr),
        .dst_addr_i (dst_addr),
        .byte_len_i (byte_len),
        .start_i (start),
        .done_o (done),
    
        // AMBA AXI interface (AW channel)
        .awid_o (awid_o),
        .awaddr_o (awaddr_o),
        .awlen_o (awlen_o),
        .awsize_o (awsize_o),
        .awburst_o (awburst_o),
        .awvalid_o (awvalid_o),
        .awready_i (awready_i),
    
        // AMBA AXI interface (W channel)
        .wid_o (wid_o),
        .wdata_o (wdata_o),
        .wstrb_o (wstrb_o),
        .wlast_o (wlast_o),
        .wvalid_o (wvalid_o),
        .wready_i (wready_i),
    
        // AMBA AXI interface (B channel)
        .bid_i (bid_i),
        .bresp_i (bresp_i),
        .bvalid_i (bvalid_i),
        .bready_o (bready_o),
    
        // AMBA AXI interface (AR channel)
        .arid_o (arid_o),
        .araddr_o (araddr_o),
        .arlen_o (arlen_o),
        .arsize_o (arsize_o),
        .arburst_o (arburst_o),
        .arvalid_o (arvalid_o),
        .arready_i (arready_i),
    
        // AMBA AXI interface (R channel)
        .rid_i (rid_i),
        .rdata_i (rdata_i),
        .rresp_i (rresp_i),
        .rlast_i (rlast_i),
        .rvalid_i (rvalid_i),
        .rready_o (rready_o)
    );
    

    endmodule <<EndOfFile:DMAC/RTL/DMAC_TOP.sv>>

    <<StartOfFile:DMAC/RTL/filelist.f>> -sverilog $LAB_PATH/RTL/DMAC_TOP.sv -sverilog $LAB_PATH/RTL/DMAC_CFG.sv -sverilog $LAB_PATH/RTL/DMAC_ENGINE.sv -sverilog $LAB_PATH/RTL/DMAC_FIFO.sv <<EndOfFile:DMAC/RTL/filelist.f>>

    <<StartOfFile:DMAC/SIM/TB/AXI_INTF.sv>> `include "../TB/AXI_TYPEDEF.svh"

    interface AXI_AW_CH #( parameter ADDR_WIDTH = AXI_ADDR_WIDTH, parameter ID_WIDTH = AXI_ID_WIDTH ) ( input clk ); logic awvalid; logic awready; logic [ID_WIDTH-1:0] awid; logic [ADDR_WIDTH-1:0] awaddr; logic [3:0] awlen; logic [2:0] awsize; logic [1:0] awburst;

    endinterface

    interface AXI_W_CH #( parameter DATA_WIDTH = AXI_DATA_WIDTH, parameter ID_WIDTH = AXI_ID_WIDTH ) ( input clk ); logic wvalid; logic wready; logic [ID_WIDTH-1:0] wid; logic [DATA_WIDTH-1:0] wdata; logic [DATA_WIDTH/8-1:0] wstrb; logic wlast;

    endinterface

    interface AXI_B_CH #( parameter ID_WIDTH = `AXI_ID_WIDTH ) ( input clk ); logic bvalid; logic bready; logic [ID_WIDTH-1:0] bid; logic [1:0] bresp;

    endinterface

    interface AXI_AR_CH #( parameter ADDR_WIDTH = AXI_ADDR_WIDTH, parameter ID_WIDTH = AXI_ID_WIDTH ) ( input clk ); logic arvalid; logic arready; logic [ID_WIDTH-1:0] arid; logic [ADDR_WIDTH-1:0] araddr; logic [3:0] arlen; logic [2:0] arsize; logic [1:0] arburst;

    endinterface

    interface AXI_R_CH #( parameter DATA_WIDTH = AXI_DATA_WIDTH, parameter ID_WIDTH = AXI_ID_WIDTH ) ( input clk ); logic rvalid; logic rready; logic [ID_WIDTH-1:0] rid; logic [DATA_WIDTH-1:0] rdata; logic [1:0] rresp; logic rlast;

    endinterface

    interface APB ( input clk ); logic psel; logic penable; logic [31:0] paddr; logic pwrite; logic [31:0] pwdata; logic pready; logic [31:0] prdata; logic pslverr;

    modport master (
        input clk,
        input pready, prdata, pslverr,
        output psel, penable, paddr, pwrite, pwdata
    );
    
    task init();
        psel = 1'b0;
        penable = 1'b0;
        paddr = 32'd0;
        pwrite = 1'b0;
        pwdata = 32'd0;
    endtask
    
    task write(input int addr,
               input int data);
        #1
        psel = 1'b1;
        penable = 1'b0;
        paddr = addr;
        pwrite = 1'b1;
        pwdata = data;
        @(posedge clk);
        #1
        penable = 1'b1;
        @(posedge clk);
    
        while (pready==1'b0) begin
            @(posedge clk);
        end
    
        psel = 1'b0;
        penable = 1'b0;
        paddr = 'hX;
        pwrite = 1'bx;
        pwdata = 'hX;
    endtask
    
    task read(input int addr,
              output int data);
        #1
        psel = 1'b1;
        penable = 1'b0;
        paddr = addr;
        pwrite = 1'b0;
        pwdata = 'hX;
        @(posedge clk);
        #1
        penable = 1'b1;
        @(posedge clk);
    
        while (pready==1'b0) begin
            @(posedge clk);
        end
        data = prdata;
    
        psel = 1'b0;
        penable = 1'b0;
        paddr = 'hX;
        pwrite = 1'bx;
        pwdata = 'hX;
    endtask
    

    endinterface <<EndOfFile:DMAC/SIM/TB/AXI_INTF.sv>>

    <<StartOfFile:DMAC/SIM/TB/AXI_SLAVE.sv>> `include "../TB/AXI_TYPEDEF.svh"

    module AXI_SLAVE #( parameter ADDR_WIDTH = 16, parameter DATA_WIDTH = AXI_DATA_WIDTH, parameter ID_WIDTH = AXI_ID_WIDTH, parameter AWREADY_DELAY = 1, parameter ARREADY_DELAY = 1, parameter AR2R_DELAY = 50 ) ( input wire clk, input wire rst_n, // _n means active low

    AXI_AW_CH aw_ch,
    AXI_W_CH w_ch,
    AXI_B_CH b_ch,
    AXI_AR_CH ar_ch,
    AXI_R_CH r_ch
    

    );

    localparam DATA_DEPTH = 1<<ADDR_WIDTH;
    
    logic [7:0] mem[DATA_DEPTH];
    
    function void write_byte(int addr, input bit [7:0] wdata);
        mem[addr] = wdata;
    endfunction
    
    function void write_word(int addr, input bit [31:0] wdata);
        for (int i=0; i<4; i++) begin
            write_byte(addr+i, wdata[8*i +: 8]); // [i*8+7:i*8]
        end
    endfunction
    
    function bit [7:0] read_byte(int addr);
        read_byte = mem[addr];
    endfunction
    
    function bit [31:0] read_word(int addr);
        for (int i=0; i<4; i++) begin
            read_word[8*i +: 8] = read_byte(addr+i);// [i*8+7:i*8]
        end
    endfunction
    
    //----------------------------------------------------------
    // write channels (AW, W, B)
    //----------------------------------------------------------
    localparam logic [1:0] S_W_IDLE = 0,
                                S_W_AWREADY = 1,
                                S_W_BURST = 2,
                                S_W_RESP = 3;
    
    logic [1:0] wstate, wstate_n;
    logic [7:0] wcnt, wcnt_n;
    
    logic [ADDR_WIDTH-1:0] waddr, waddr_n;
    logic [ID_WIDTH-1:0] wid, wid_n;
    logic [3:0] wlen, wlen_n;
    
    always_ff @(posedge clk)
        if (!rst_n) begin
            wstate <= S_W_IDLE;
    
            wcnt <= 8'd0;
            waddr <= {ADDR_WIDTH{1'b0}};
            wid <= {ID_WIDTH{1'b0}};
            wlen <= 4'd0;
        end
        else begin
            wstate <= wstate_n;
    
            wcnt <= wcnt_n;
            waddr <= waddr_n;
            wid <= wid_n;
            wlen <= wlen_n;
        end
    
    always @(*) begin
        wstate_n = wstate;
    
        wcnt_n = wcnt;
        waddr_n = waddr;
        wid_n = wid;
        wlen_n = wlen;
    
        aw_ch.awready = 1'b0;
        w_ch.wready = 1'b0;
        b_ch.bvalid = 1'b0;
    
        case (wstate)
            S_W_IDLE: begin
                if (aw_ch.awvalid) begin
                    if (AWREADY_DELAY == 0) begin
                        waddr_n = aw_ch.awaddr;
                        wid_n = aw_ch.awid;
                        wlen_n = aw_ch.awlen;
                        aw_ch.awready = 1'b1;
                        wstate_n = S_W_BURST;
                    end
                    else begin
                        wcnt_n = AWREADY_DELAY-1;
                        wstate_n = S_W_AWREADY;
                    end
                end
            end
            S_W_AWREADY: begin
                if (wcnt==0) begin
                    waddr_n = aw_ch.awaddr;
                    wid_n = aw_ch.awid;
                    wlen_n = aw_ch.awlen;
                    aw_ch.awready = 1'b1;
                    wstate_n = S_W_BURST;
                end
                else begin
                    wcnt_n = wcnt - 8'd1;
                end
            end
            S_W_BURST: begin
                w_ch.wready = 1'b1;
                if (w_ch.wvalid) begin
                    for (int i=0; i<DATA_WIDTH/8; i++) begin
                        write_byte(waddr + i, w_ch.wdata[i*8 +: 8]); // [i*8+7:i*8]
                    end
                    waddr_n = waddr + (DATA_WIDTH/8);
                    if (wlen==4'd0) begin
                        wstate_n = S_W_RESP;
                    end
                    else begin
                        wlen_n = wlen - 4'd1;
                    end
                end
            end
            S_W_RESP: begin
                b_ch.bvalid = 1'b1;
                if (b_ch.bready) begin
                    wstate_n = S_W_IDLE;
                end
            end
        endcase
    end
    
    //----------------------------------------------------------
    // read channel (AR, R)
    //----------------------------------------------------------
    localparam logic [1:0] S_R_IDLE = 0,
                                S_R_ARREADY = 1,
                                S_R_DELAY = 2,
                                S_R_BURST = 3;
    
    logic [1:0] rstate, rstate_n;
    logic [7:0] rcnt, rcnt_n;
    
    logic [ADDR_WIDTH-1:0] raddr, raddr_n;
    logic [ID_WIDTH-1:0] rid, rid_n;
    logic [3:0] rlen, rlen_n;
    
    always_ff @(posedge clk)
        if (!rst_n) begin
            rstate <= S_R_IDLE;
    
            rcnt <= 8'd0;
            raddr <= {ADDR_WIDTH{1'b0}};
            rid <= {ID_WIDTH{1'b0}};
            rlen <= 4'd0;
        end
        else begin
            rstate <= rstate_n;
    
            rcnt <= rcnt_n;
            raddr <= raddr_n;
            rid <= rid_n;
            rlen <= rlen_n;
        end
    
    always_comb begin
        rstate_n = rstate;
    
        rcnt_n = rcnt;
        raddr_n = raddr;
        rid_n = rid;
        rlen_n = rlen;
    
        ar_ch.arready = 1'b0;
        r_ch.rvalid = 1'b0;
        r_ch.rlast = 1'b0;
    
        case (rstate)
            S_R_IDLE: begin
                if (ar_ch.arvalid) begin
                    if (ARREADY_DELAY == 0) begin
                        raddr_n = ar_ch.araddr;
                        rid_n = ar_ch.arid;
                        rlen_n = ar_ch.arlen;
                        ar_ch.arready = 1'b1;
    
                        rcnt_n = AR2R_DELAY - 1;
                        rstate_n = S_R_DELAY;
                    end
                    else begin
                        rcnt_n = ARREADY_DELAY-1;
                        rstate_n = S_R_ARREADY;
                    end
                end
            end
            S_R_ARREADY: begin
                if (rcnt==0) begin
                    raddr_n = ar_ch.araddr;
                    rid_n = ar_ch.arid;
                    rlen_n = ar_ch.arlen;
                    ar_ch.arready = 1'b1;
    
                    rcnt_n = AR2R_DELAY - 1;
                    rstate_n = S_R_DELAY;
                end
                else begin
                    rcnt_n = rcnt - 8'd1;
                end
            end
            S_R_DELAY: begin
                if (rcnt==0) begin
                    rstate_n = S_R_BURST;
                end
                else begin
                    rcnt_n = rcnt - 8'd1;
                end
            end
            S_R_BURST: begin
                r_ch.rvalid = 1'b1;
                r_ch.rlast = (rlen==4'd0);
                for (int i=0; i<DATA_WIDTH/8; i++) begin
                    r_ch.rdata[i*8 +: 8] = read_byte(raddr + i); // [i*8+7:i*8]
                end
                if (r_ch.rready) begin
                    raddr_n = raddr + (DATA_WIDTH/8);
                    if (rlen==4'd0) begin
                        rstate_n = S_R_IDLE;
                    end
                    else begin
                        rlen_n = rlen - 4'd1;
                    end
                end
            end
        endcase
    end
    
    // output assignments
    assign b_ch.bid = wid;
    assign b_ch.bresp = 2'd0;
    assign r_ch.rid = rid;
    assign r_ch.rresp = 2'd0;
    

    endmodule <<EndOfFile:DMAC/SIM/TB/AXI_SLAVE.sv>>

    <<StartOfFile:DMAC/SIM/TB/AXI_TYPEDEF.svh>> ifndef __AXI_TYPEDEF_SVH__ define AXI_TYPEDEF_SVH

    define AXI_ADDR_WIDTH 32 define AXI_DATA_WIDTH 32 `define AXI_ID_WIDTH 4

    `endif /* AXI_TYPEDEF_SVH */ <<EndOfFile:DMAC/SIM/TB/AXI_TYPEDEF.svh>>

    <<StartOfFile:DMAC/SIM/TB/DMAC_TOP_TB.sv>> define IP_VER 32'h000 define SRC_ADDR 32'h100 define DST_ADDR 32'h104 define LEN_ADDR 32'h108 define STAT_ADDR 32'h110 define START_ADDR 32'h10c

    `define TIMEOUT_CYCLE 999999 module DMAC_TOP_TB ();

    reg clk;
    reg rst_n;
    
    // clock generation
    initial begin
        clk = 1'b0;
    
        forever #10 clk = !clk;
    end
    
    // reset generation
    initial begin
        rst_n = 1'b0; // active at time 0
    
        repeat (3) @(posedge clk); // after 3 cycles,
        rst_n = 1'b1; // release the reset
    end
    
    // enable waveform dump
    initial begin
        \$dumpvars(0, u_DUT);
        \$dumpfile("dump.vcd");
    end
    

    // timeout initial begin #`TIMEOUT_CYCLE $display("Timeout!"); $finish; end

    APB apb_if (.clk(clk));
    
    AXI_AW_CH aw_ch (.clk(clk));
    AXI_W_CH w_ch (.clk(clk));
    AXI_B_CH b_ch (.clk(clk));
    AXI_AR_CH ar_ch (.clk(clk));
    AXI_R_CH r_ch (.clk(clk));
    
    task test_init();
        int data;
        apb_if.init();
    
        @(posedge rst_n); // wait for a release of the reset
        repeat (10) @(posedge clk); // wait another 10 cycles
    
        apb_if.read(`IP_VER, data);
        \$display("---------------------------------------------------");
        \$display("IP version: %x", data);
        \$display("---------------------------------------------------");
    
        \$display("---------------------------------------------------");
        \$display("Reset value test");
        \$display("---------------------------------------------------");
        apb_if.read(`SRC_ADDR, data);
        if (data===0)
            \$display("DMA_SRC(pass): %x", data);
        else begin
            \$display("DMA_SRC(fail): %x", data);
            @(posedge clk);
            \$finish;
        end
        apb_if.read(`DST_ADDR, data);
        if (data===0)
            \$display("DMA_DST(pass): %x", data);
        else begin
            \$display("DMA_DST(fail): %x", data);
            @(posedge clk);
            \$finish;
        end
        apb_if.read(`LEN_ADDR, data);
        if (data===0)
            \$display("DMA_LEN(pass): %x", data);
        else begin
            \$display("DMA_LEN(fail): %x", data);
            @(posedge clk);
            \$finish;
        end
        apb_if.read(`STAT_ADDR, data);
        if (data===1)
            \$display("DMA_STATUS(pass): %x", data);
        else begin
            \$display("DMA_STATUS(fail): %x", data);
            @(posedge clk);
            \$finish;
        end
    endtask
    
    task test_dma(input int src, input int dst, input int len);
        int data;
        int word;
        realtime elapsed_time;
    
        \$display("---------------------------------------------------");
        \$display("Load data to memory");
        \$display("---------------------------------------------------");
        for (int i=src; i<(src+len); i=i+4) begin
            word = \$random; 
            u_mem.write_word(i, word);
        end
    
        \$display("---------------------------------------------------");
        \$display("Configuration test");
        \$display("---------------------------------------------------");
        apb_if.write(`SRC_ADDR, src);
        apb_if.read(`SRC_ADDR, data);
        if (data===src)
            \$display("DMA_SRC(pass): %x", data);
        else begin
            \$display("DMA_SRC(fail): %x", data);
            @(posedge clk);
            \$finish;
        end
        apb_if.write(`DST_ADDR, dst);
        apb_if.read(`DST_ADDR, data);
        if (data===dst)
            \$display("DMA_DST(pass): %x", data);
        else begin
            \$display("DMA_DST(fail): %x", data);
            @(posedge clk);
            \$finish;
        end
        apb_if.write(`LEN_ADDR, len);
        apb_if.read(`LEN_ADDR, data);
        if (data===len)
            \$display("DMA_LEN(pass): %x", data);
        else begin
            \$display("DMA_LEN(fail): %x", data);
            @(posedge clk);
            \$finish;
        end
    
        \$display("---------------------------------------------------");
        \$display("DMA start");
        \$display("---------------------------------------------------");
        apb_if.write(`START_ADDR, 32'h1);
        elapsed_time = \$realtime;
    
        \$display("---------------------------------------------------");
        \$display("Wait for a DMA completion");
        \$display("---------------------------------------------------");
        data = 0;
        while (data!=1) begin
            apb_if.read(`STAT_ADDR, data);
            repeat (100) @(posedge clk);
        end
        @(posedge clk);
        elapsed_time = \$realtime - elapsed_time;
        \$timeformat(-9, 0, " ns", 10);
        \$display("Elapsed time for DMA: %t", elapsed_time);
    
        \$display("---------------------------------------------------");
        \$display("DMA completed");
        \$display("---------------------------------------------------");
    
        repeat (len) @(posedge clk); // to make sure data is written
    
        \$display("---------------------------------------------------");
        \$display("verify data");
        \$display("---------------------------------------------------");
        for (int i=0; i<len; i=i+4) begin
            logic [31:0] src_word;
            logic [31:0] dst_word;
            src_word = u_mem.read_word(src+i);
            dst_word = u_mem.read_word(dst+i);
            if (src_word!==dst_word) begin
                \$display("Mismatch! (src:%x @%x, dst:%x @%x", src_word, src+i, dst_word, dst+i);
            end
        end
    endtask
    
    int src,
                    dst,
                    len;
    
    // main
    initial begin
        test_init();
    
        src = 'h0000_1000;
        dst = 'h0000_2000;
        len = 'h0100;
        \$display("===================================================");
        \$display("= 1st trial"); 
        \$display("= Copying %x bytes from %x to %x", len, src, dst);
        \$display("===================================================");
        test_dma(src, dst, len);
    
        src = 'h1234_1234;
        dst = 'hABCD_ABCC;
        len = 'h0F00;
        \$display("===================================================");
        \$display("= 2nd trial (long transfer)");
        \$display("= Copying %x bytes from %x to %x", len, src, dst);
        \$display("===================================================");
        test_dma(src, dst, len);
    
        src = 'h4278_0000;
        dst = 'h4278_1000;
        len = 'h0F10;
        \$display("===================================================");
        \$display("= 3rd trial (long transfer-2)");
        \$display("= Copying %x bytes from %x to %x", len, src, dst);
        \$display("===================================================");
        test_dma(src, dst, len);
        \$finish;
    end
    
    
    AXI_SLAVE u_mem (
        .clk (clk),
        .rst_n (rst_n),
    
        .aw_ch (aw_ch),
        .w_ch (w_ch),
        .b_ch (b_ch),
        .ar_ch (ar_ch),
        .r_ch (r_ch)
    );
    
    DMAC_TOP u_DUT (
        .clk (clk),
        .rst_n (rst_n),
    
        // APB interface
        .psel_i (apb_if.psel),
        .penable_i (apb_if.penable),
        .paddr_i (apb_if.paddr[11:0]),
        .pwrite_i (apb_if.pwrite),
        .pwdata_i (apb_if.pwdata),
        .pready_o (apb_if.pready),
        .prdata_o (apb_if.prdata),
        .pslverr_o (apb_if.pslverr),
    
        // AXI AW channel
        .awid_o (aw_ch.awid),
        .awaddr_o (aw_ch.awaddr),
        .awlen_o (aw_ch.awlen),
        .awsize_o (aw_ch.awsize),
        .awburst_o (aw_ch.awburst),
        .awvalid_o (aw_ch.awvalid),
        .awready_i (aw_ch.awready),
    
        // AXI W channel
        .wid_o (w_ch.wid),
        .wdata_o (w_ch.wdata),
        .wstrb_o (w_ch.wstrb),
        .wlast_o (w_ch.wlast),
        .wvalid_o (w_ch.wvalid),
        .wready_i (w_ch.wready),
    
        // AXI B channel
        .bid_i (b_ch.bid),
        .bresp_i (b_ch.bresp),
        .bvalid_i (b_ch.bvalid),
        .bready_o (b_ch.bready),
    
        // AXI AR channel
        .arid_o (ar_ch.arid),
        .araddr_o (ar_ch.araddr),
        .arlen_o (ar_ch.arlen),
        .arsize_o (ar_ch.arsize),
        .arburst_o (ar_ch.arburst),
        .arvalid_o (ar_ch.arvalid),
        .arready_i (ar_ch.arready),
    
        // AXI R channel
        .rid_i (r_ch.rid),
        .rdata_i (r_ch.rdata),
        .rresp_i (r_ch.rresp),
        .rlast_i (r_ch.rlast),
        .rvalid_i (r_ch.rvalid),
        .rready_o (r_ch.rready)
    );
    

    endmodule <<EndOfFile:DMAC/SIM/TB/DMAC_TOP_TB.sv>>

    <<StartOfFile:DMAC/SIM/TB/filelist.f>> $LAB_PATH/SIM/TB/timescale.v $LAB_PATH/SIM/TB/AXI_INTF.sv $LAB_PATH/SIM/TB/AXI_SLAVE.sv $LAB_PATH/SIM/TB/DMAC_TOP_TB.sv <<EndOfFile:DMAC/SIM/TB/filelist.f>>

    <<StartOfFile:DMAC/SIM/TB/timescale.v>> `timescale 1ns/1ps <<EndOfFile:DMAC/SIM/TB/timescale.v>>

    <<StartOfFile:DMAC/SIM/run.compile>> #!/bin/bash

    source ../../scripts/common.sh

    export LAB_PATH="$PWD/../" FILELIST_TB="../TB/filelist.f" FILELIST_RTL="../../RTL/filelist.f"

    echo "Cleaning up the old directory" rm -rf $RUN_DIR echo "Creating a new directory" mkdir -p $RUN_DIR cd $RUN_DIR echo "Compiling" $COMPILE_CMD $COMPILE_OPTIONS -f $FILELIST_TB -f $FILELIST_RTL <<EndOfFile:DMAC/SIM/run.compile>>

    <<StartOfFile:DMAC/SIM/run.compile4cov>> #!/bin/bash

    source ../../scripts/common.sh

    export LAB_PATH="$PWD/../" COV_DIR="$PWD/VDB" COV_OPTIONS="-cm line+cond+fsm+tgl+branch -cm_dir $COV_DIR" FILELIST_TB="../TB/filelist.f" FILELIST_RTL="../../RTL/filelist.f"

    echo "Cleaning up the old directory" rm -rf $RUN_DIR echo "Creating a new directory" mkdir -p $RUN_DIR cd $RUN_DIR echo "Compiling" $COMPILE_CMD $COMPILE_OPTIONS $COV_OPTIONS -f $FILELIST_TB -f $FILELIST_RTL <<EndOfFile:DMAC/SIM/run.compile4cov>>

    <<StartOfFile:DMAC/SIM/run.sim>> #!/bin/bash

    source ../../scripts/common.sh

    if [ -e $RUN_DIR/simv ]; then cd $RUN_DIR ./simv else echo "Compile file does not exist" exit 1 fi <<EndOfFile:DMAC/SIM/run.sim>>

    <<StartOfFile:DMAC/SIM/run.sim4cov>> #!/bin/bash

    source ../../scripts/common.sh

    COV_DIR="$PWD/VDB" COV_OPTIONS="-cm line+cond+fsm+tgl+branch -cm_dir $COV_DIR"

    if [ -e $RUN_DIR/simv ]; then cd $RUN_DIR ./simv $COV_OPTIONS else echo "Compile file does not exist" exit 1 fi <<EndOfFile:DMAC/SIM/run.sim4cov>>

    <<StartOfFile:DMAC/SIM/run.verdi>> #!/bin/bash

    source ../../scripts/common.sh

    export LAB_PATH="$PWD/../" FILELIST_TB="../TB/filelist.f" FILELIST_RTL="../../RTL/filelist.f"

    cd $RUN_DIR $VERDI_CMD $VERDI_OPTIONS -f $FILELIST_TB -f $FILELIST_RTL <<EndOfFile:DMAC/SIM/run.verdi>>

    <<StartOfFile:DMAC/SIM/run.verdi4cov>> verdi -cov -covdir VDB.vdb/ <<EndOfFile:DMAC/SIM/run.verdi4cov>>

    <<StartOfFile:DMAC/SIM/run.waveform>> #!/bin/bash

    source ../../scripts/common.sh

    if [ -e $RUN_DIR/dump.vcd ]; then cd $RUN_DIR $WAVE_CMD $WAVE_OPTIONS -i dump.vcd else echo "Dump file does not exist" exit 1 fi <<EndOfFile:DMAC/SIM/run.waveform>>

  2. Assistant

    Certainly! It appears that you've shared a comprehensive set of files related to a Direct Memory Access Controller (DMAC) project, including Verilog/SystemVerilog modules, testbenches, and scripts for compilation, simulation, waveform viewing, and code coverage analysis. The key parts of the Direct Memory Access Controller include configuration (DMAC_CFG), engine (DMAC_ENGINE), a FIFO buffer (DMAC_FIFO), and the top module (DMAC_TOP) which integrates all components and interfaces.

    To focus on the specific request you've made for providing code where indicated as "FILL YOUR CODE HERE" in the DMAC_ENGINE module, let's look into that.

    Given the descriptions and comments inside the DMAC_ENGINE module, the primary role of the always_comb block where the code needs to be filled is to handle the state transitions and control signals based on the current state of the DMA operation. Let's go ahead and fill this in based on the state definitions and expected behavior outlined in the comments.

    Code to Fill "FILL YOUR CODE HERE"

    For DMAC_ENGINE.sv, always_comb logic for managing various states can be implemented as:

    // this block programs output values and next register values
    // based on states.
    always_comb begin
        state_n = state; // Default to retaining current state unless a state change is dictated by logic below.
        // Default next values for control registers to their current state to preserve values unless specifically changed below
        src_addr_n = src_addr;
        dst_addr_n = dst_addr;
        cnt_n = cnt;
        wcnt_n = wcnt;
        
        arvalid = 0;
        rready = 0;
        awvalid = 0;
        wvalid = 0;
        wlast = 0;
        fifo_rden = 0;
        fifo_wren = 0;
        done = 0;
        
        case (state)
            S_IDLE: begin
                if (start_i) begin
                    arvalid = 1; // Start with read request
                    state_n = S_RREQ;
                    src_addr_n = src_addr_i;
                    dst_addr_n = dst_addr_i;
                    cnt_n = byte_len_i;
                    wcnt_n = 0; // Reset write counter
                end
            end
            S_RREQ: begin
                if (arready_i) begin
                    arvalid = 0; // Clear read request
                    state_n = S_RDATA;
                    rready = 1;
                end
            end
            S_RDATA: begin
                rready = 1;
                fifo_wren = rvalid_i & rready;
                if (rlast_i && rvalid_i && rready) begin
                    state_n = S_WREQ;
                end
            end
            S_WREQ: begin
                if (!fifo_empty) begin
                    awvalid = 1; // Indicate write request
                    state_n = S_WDATA;
                end
            end
            S_WDATA: begin
                if (awready_i && !fifo_empty) begin
                    awvalid = 0; // Clear write request flag
                    fifo_rden = 1;
                    wvalid = 1;
                    wcnt_n = wcnt + 1;
                    if (wcnt_n == cnt) begin
                        wlast = 1;
                        wvalid = 0;
                        state_n = S_IDLE;
                        done = 1; // DMA operation complete
                    end
                end
            end
        endcase
    end
    

    This code snippet covers basic operation flow for a DMA engine based on the various states it can be in: Idle, read request, read data processing, write request, and write data processing. It also handles the read-data-write cycle with a simple FIFO buffer for data transfer, assuming a continuous stream of data being read from a source address and written to a destination address.

    Remember, the actual implementation detail may vary based on unknown specifications or provisions outside of what's outlined here, such as timing considerations, exact handling of handshake signals, or additional operational features not captured entirely within the given scope.

  3. User

    이 코드에서 wire는 무엇인가?

  4. Assistant

    wire는 Verilog HDL (Hardware Description Language) 및 SystemVerilog에서 사용되는 기본적인 데이터 타입 중 하나입니다. 이것은 디지털 신호를 나타내는 데 사용되며, 일반적으로 회로 내에서 연속적인 연결이나, 모듈 간의 연결을 표현하는 데 쓰입니다. wire는 기본적으로 1비트의 값을 가지지만, 벡터 형식으로 확장하여 다중 비트 신호를 표현할 수도 있습니다.

    wire는 다음과 같은 특징을 가집니다:

    • 비저장형(logic type): wire는 스토리지 엘리먼트가 아니기 때문에, 자체적으로 값을 저장할 수 없습니다. 대신, 신호의 값을 다른 신호나 모듈의 출력과 연결하기 위해 사용됩니다.

    • 연속 할당 가능: wire는 연속 할당(conitnuous assignment) 문에 사용되어 한 신호의 값을 다른 신호에 할당할 수 있습니다. 연속 할당은 항상 활성 상태로 있어서 할당된 신호의 값이 변할 때마다 wire의 값도 즉시 업데이트 됩니다.

    예를 들어, 하나의 모듈 출력을 다른 모듈의 입력에 연결하거나, 간단한 조합 회로를 구현할 때 wire가 사용됩니다.

    module exampleModule(input wire a, input wire b, output wire c);
        assign c = a & b; // a AND b의 결과를 c에 연속 할당
    endmodule
    

    이 예에서, a와 b는 입력 신호로 wire 타입을 사용하며, c는 출력에 사용됩니다. assign 문은 a와 b의 논리 AND 연산 결과를 항상 c에 할당합니다. 여기서 assign은 연속 할당을 의미하여, a나 b의 값이 바뀌면 그 즉시 c의 값도 업데이트됩니다.

    SystemVerilog에서는 좀 더 유연한 logic 타입도 도입되어 wire와 유사한 역할을 하면서도 좀 더 복잡한 사용 사례를 지원합니다. 하지만, 기본적인 개념은 wire를 통해 이해할 수 있습니다.

  5. User

    즉, 값을 입력할 순 없지만 참조할 순 있는건가?

  6. Assistant

    네, 맞습니다. wire는 Verilog 및 SystemVerilog에서 값을 직접 저장하거나 "입력"하는 데 사용되지 않습니다. 대신에 wire는 신호를 전달하거나 참조하는데 사용됩니다. 다시 말해, wire는 회로 내에서 하나의 지점에서 다른 지점으로 신호를 "전달"하는 역할을 하며, 이러한 신호는 다른 모듈의 출력이나, assign 문을 통해 결정된 값을 반영합니다.

    wire에 할당된 값은 다음과 같은 방법으로 정의됩니다:

    • 다른 모듈의 출력이나
    • assign 문을 통한 연속적인 할당을 통해

    또한, wire는 조합적 논리(Combinational Logic)의 결과를 전달하는데 자주 사용됩니다. wire는 양방향 통신을 지원하지 않기 때문에, 출력 신호를 다른 위치로 "전달"하는 역할에 한합니다.

    예를 들어:

    module myModule(input wire a, input wire b, output wire sum, output wire carry);
        assign sum = a ^ b;    // XOR 연산 결과
        assign carry = a & b;  // AND 연산 결과
    endmodule
    

    이 예에서, sum과 carry는 wire 타입으로, 두 입력 신호 a와 b에 대한 논리 연산 결과를 "참조"하여 그 값을 나타냅니다. 이때 assign 문이 연속 할당을 통해 sum과 carry에 값을 할당합니다. 따라서, wire는 직접 값을 "입력" 받는 것이 아니라, 다른 신호의 값을 참조하거나 전달하는 데 적합합니다.

  7. User

    XOR에 대해서 설명해줘.

  8. Assistant

    XOR는 "배타적 논리합"을 의미하는 논리 연산자로, 두 입력값이 서로 다를 때 참(1)을, 두 입력값이 서로 같을 때 거짓(0)을 출력합니다. XOR 연산은 디지털 회로 설계, 암호학, 오류 검출 및 교정 코드 등 다양한 분야에서 중요하게 사용됩니다.

    XOR의 진리표

    A (입력1)B (입력2)A XOR B (출력)
    000
    011
    101
    110

    여기에서 볼 수 있듯, 두 입력의 값이 같지 않을 때(즉, 하나는 0이고 다른 하나는 1일 때) 출력이 1이 됩니다. 반면, 두 입력이 모두 0이거나 모두 1일 때 출력은 0이 됩니다.

    XOR 연산의 특징

    1. 배타성 (Exclusiveness): XOR은 두 입력이 서로 "배타적"일 때만 참을 결과로 합니다. 이는 두 값이 서로 다를 경우에만 참이 됨을 의미합니다.

    2. 대칭성 (Symmetry): A XOR B는 B XOR A와 같습니다. 즉, 입력의 순서를 바꿔도 결과는 동일합니다.

    3. 반전 특성 (Inversion Property): 한 입력값이 변경될 때마다 출력 값 역시 변경됩니다. 예를 들어, A = 1, B = 0일 때, A XOR B = 1입니다. 만약 A나 B 중 하나가 반전되면 출력도 반전됩니다.

    4. 자기 복원성 (Self-duality): 입력 중 하나가 1일 때, XOR 연산은 다른 입력값을 "반전"시킵니다. 예를 들어, A XOR 1 = ~A입니다.

    XOR 연산의 활용 예

    • 암호화: XOR 연산은 간단한 암호화와 암호 해독에 사용될 수 있습니다. 데이터를 암호화하기 위해 특정 키와 XOR 연산을 수행하고, 같은 키와 다시 XOR 연산을 수행하여 원래 데이터를 복구할 수 있습니다.

    • 패리티 비트: XOR 연산은 데이터 전송 중 오류를 검출하기 위한 패리티 비트 생성에 사용됩니다. 데이터 비트의 패리티(홀수/짝수)를 결정하여 추가 비트로 전송함으로써, 수신 측에서 패리티를 검사하여 한 비트의 오류를 발견할 수 있습니다.

    • 디지털 회로: XOR 게이트는 전가산기와 같은 복잡한 디지털 회로를 구성하는 데 필수적인 기본 논리 게이트 중 하나입니다.

    XOR 연산의 이러한 특성과 활용 사례는 그것이 디지털 시스템과 암호학에서 왜 중요한지를 잘 보여줍니다.