Skip to content
TheChatArchiveThe Chat Archive
gpt-4-0125-preview· OpenAIAi2 WildChat-4.8M (AI2)

"fifofull, fifoempty, fifowren, fiforden를 사용해서 FIFO를 사용하도록 코드를 수정하시오."를 영작해줘.

  1. User

    "fifo_full, fifo_empty, fifo_wren, fifo_rden를 사용해서 FIFO를 사용하도록 코드를 수정하시오."를 영작해줘.

  2. Assistant

    "Modify the code to utilize FIFO using fifo_full, fifo_empty, fifo_wren, and fifo_rden."

  3. User

    Modify the code to utilize FIFO using fifo_full, fifo_empty, fifo_wren, and fifo_rden Please fix the modifiable code in the file "DMAC/RTL/DMAC_ENGINE.sv" by modifying it.

    { "signal": [ { "name": "clk", "wave": "p....|....|.......|....." }, { "name": "state", "wave": "2.3.4|....|..5.6..|..3.4", "data": ["IDLE", "RREQ", "RDATA", "WREQ", "WDATA", "RREQ"] }, { "name": "write to CMD", "wave": "010..|....|.......|.....", "data": ["1"] }, {}, [ "AR ch", { "name": "ARVALID(out)", "wave": "0.1.0|....|.......|.....", "data": ["SRC"] }, { "name": "ARADDR(out)", "wave": "x.3.x|....|.......|.....", "data": ["SRC"] }, { "name": "ARLEN(out)", "wave": "2....|....|.......|.....", "data": ["15"] }, { "name": "ARREADY(in)", "wave": "0..10|....|.......|....." }, ], [ "R ch", { "name": "RREADY(out)", "wave": "0...1|....|..0....|....." }, { "name": "RVALID(in)", "wave": "0....|.1..|..0....|....." }, { "name": "RLAST(in)", "wave": "0....|....|.10....|....." }, { "name": "RDATA(in)", "wave": "x....|.444|44x....|.....", "data": ["D0", "D1", "D2", "D14", "D15"] }, ], [ "AW ch", { "name": "AWVALID(out)", "wave": "0....|....|..1.0..|....." }, { "name": "AWADDR(out)", "wave": "x....|....|..5.x..|.....", "data": ["DST"] }, { "name": "AWLEN(out)", "wave": "2....|....|.......|.....", "data": ["15"] }, { "name": "AWREADY(in)", "wave": "0....|....|...10..|....." }, ], [ "W ch", { "name": "WVALID(out)", "wave": "0....|....|....1..|..0.." }, { "name": "WDATA(out)", "wave": "x....|....|....444|44x..", "data": ["D0", "D1", "D2", "D14", "D15"] }, { "name": "WLAST(out)", "wave": "0....|....|.......|.10.." }, { "name": "WREADY(in)", "wave": "0....|....|....1..|..0.." } ] ], "head" : { "tick" : "0" }, "foot" : { "tick" : "0" } } 그림 3. DMA operation with burst transfers. At a time, a request reads/writes 16 cycles of data.

    Please verify if the following table is correct using the code provided below.

    +-------+-------------------------------------------------------------------------------------+------------+-----------------------------------------------------------+-----------------------------------------+ | State | Major outputs | Next State | Next state transition condition | Notes | | +---------+--------+---------------------------------------+-------------------+------+ | | | | | ARVALID | RREADY | AWVALID | WVALID | done | | | | +-------+---------+--------+---------------------------------------+-------------------+------+------------+-----------------------------------------------------------+-----------------------------------------+ | IDLE | 0 | 0 | 0 | 0 | 1 | RREQ | (DMA_CMD.start is written as 1) and (DMA_LEN.byte_len!=0) | On moving out, | | | | | | | | | | - Copy DMA_SRC to SRC_ADDR. | | | | | | | | | | - Copy DMA_DST to DST_ADDR | | | | | | | | | | - Copy DMA_LEN to the internal counter | +-------+---------+--------+---------------------------------------+-------------------+------+------------+-----------------------------------------------------------+-----------------------------------------+ | RREQ | 1 | 0 | 0 | 0 | 0 | RDATA | ARREADY=1 | On moving out, | | | | | | | | | | - Increment ARADDR by 4 | | | | | | | | | | | | | | | | | | | | ARLEN = (cnt>=64) ? 'hF : cnt[5:2]-4'h1 | +-------+---------+--------+---------------------------------------+-------------------+------+------------+-----------------------------------------------------------+-----------------------------------------+ | RDATA | 0 | 1 | 0 | 0 | 0 | WREQ | (RVALID=1) & (RLAST) | Push data to FIFO | | | | | | | +------------+-----------------------------------------------------------+-----------------------------------------+ | | | | | | | RDATA | (RVALID) & (!RLAST) | Push data to FIFO | +-------+---------+--------+---------------------------------------+-------------------+------+------------+-----------------------------------------------------------+-----------------------------------------+ | WREQ | 0 | 0 | 1 | 0 | 0 | WDATA | AWREADY=1 | On moving out, | | | | | AWLEN=(cnt>=64) ? 'hF : cnt[5:2]-4'h1 | | | | | - Increment AWADDR by 4 | | | | | | | | | | - Decrement the internal counter by 4 | +-------+---------+--------+---------------------------------------+-------------------+------+------------+-----------------------------------------------------------+-----------------------------------------+ | WDATA | 0 | 0 | 0 | 1 | 0 | RREQ | (WREADY=1) (!WLAST) & (counter!=0) | Pop data from FIFO | | | | | | WLAST=(wcnt=='d0) | | | | Decrement wcnt | | | | | | | +------------+-----------------------------------------------------------+-----------------------------------------+ | | | | | | | IDLE | (WREADY=1) (WLAST) & (counter==0) | Pop data from FIFO | +-------+---------+--------+---------------------------------------+-------------------+------+------------+-----------------------------------------------------------+-----------------------------------------+

    <<StartOfFile:DMAC/RTL/DMAC_FIFO.sv>> module DMAC_FIFO #( parameter DEPTH_LG2 = 4, parameter DATA_WIDTH = 32 ) ( input wire clk, input wire rst_n,

    output wire full_o,
    input wire wren_i,
    input wire [DATA_WIDTH-1:0] wdata_i,
    
    output wire empty_o,
    input wire rden_i,
    output wire [DATA_WIDTH-1:0] rdata_o
    

    );

    localparam FIFO_DEPTH = (1<<DEPTH_LG2);
    
    reg [DATA_WIDTH-1:0] data[FIFO_DEPTH];
    
    reg full, full_n,
                                        empty, empty_n;
    reg [DEPTH_LG2:0] wrptr, wrptr_n,
                                        rdptr, rdptr_n;
    
    // reset entries to all 0s
    always_ff @(posedge clk)
        if (!rst_n) begin
            full <= 1'b0;
            empty <= 1'b1; // empty after as reset
    
            wrptr <= {(DEPTH_LG2+1){1'b0}};
            rdptr <= {(DEPTH_LG2+1){1'b0}};
    
            for (int i=0; i<FIFO_DEPTH; i++) begin
                data[i] <= {DATA_WIDTH{1'b0}};
            end
        end
        else begin
            full <= full_n;
            empty <= empty_n;
    
            wrptr <= wrptr_n;
            rdptr <= rdptr_n;
    
            if (wren_i) begin
                data[wrptr[DEPTH_LG2-1:0]] <= wdata_i;
            end
        end
    
    always_comb begin
        wrptr_n = wrptr;
        rdptr_n = rdptr;
    
        if (wren_i) begin
            wrptr_n = wrptr + 'd1;
        end
    
        if (rden_i) begin
            rdptr_n = rdptr + 'd1;
        end
    
        empty_n = (wrptr_n == rdptr_n);
        full_n = (wrptr_n[DEPTH_LG2]!=rdptr_n[DEPTH_LG2])
                                     &(wrptr_n[DEPTH_LG2-1:0]==rdptr_n[DEPTH_LG2-1:0]);
    
    end
    
    // synthesis translate_off
    always @(posedge clk) begin
        if (full_o & wren_i) begin
            \$display("FIFO overflow");
            @(posedge clk);
            \$finish;
        end
    end
    
    always @(posedge clk) begin
        if (empty_o & rden_i) begin
            \$display("FIFO underflow");
            @(posedge clk);
            \$finish;
        end
    end
    // synthesis translate_on
    
    assign full_o = full;
    assign empty_o = empty;
    assign rdata_o = data[rdptr[DEPTH_LG2-1:0]];
    

    endmodule <<EndOfFile:DMAC/RTL/DMAC_FIFO.sv>>

    <<StartOfFile:DMAC/RTL/DMAC_ENGINE.sv>> module DMAC_ENGINE ( input wire clk, input wire rst_n, // _n means active low

    // configuration registers
    input wire [31:0] src_addr_i,
    input wire [31:0] dst_addr_i,
    input wire [15:0] byte_len_i,
    input wire start_i,
    output wire done_o,
    
    // AMBA AXI interface (AW channel)
    output wire [3:0] awid_o,
    output wire [31:0] awaddr_o,
    output wire [3:0] awlen_o,
    output wire [2:0] awsize_o,
    output wire [1:0] awburst_o,
    output wire awvalid_o,
    input wire awready_i,
    
    // AMBA AXI interface (W channel)
    output wire [3:0] wid_o,
    output wire [31:0] wdata_o,
    output wire [3:0] wstrb_o,
    output wire wlast_o,
    output wire wvalid_o,
    input wire wready_i,
    
    // AMBA AXI interface (B channel)
    input wire [3:0] bid_i,
    input wire [1:0] bresp_i,
    input wire bvalid_i,
    output wire bready_o,
    
    // AMBA AXI interface (AR channel)
    output wire [3:0] arid_o,
    output wire [31:0] araddr_o,
    output wire [3:0] arlen_o,
    output wire [2:0] arsize_o,
    output wire [1:0] arburst_o,
    output wire arvalid_o,
    input wire arready_i,
    
    // AMBA AXI interface (R channel)
    input wire [3:0] rid_i,
    input wire [31:0] rdata_i,
    input wire [1:0] rresp_i,
    input wire rlast_i,
    input wire rvalid_i,
    output wire rready_o
    

    );

    // mnemonics for state values
    localparam S_IDLE = 3'd0,
                                S_RREQ = 3'd1,
                                S_RDATA = 3'd2,
                                S_WREQ = 3'd3,
                                S_WDATA = 3'd4;
    
    reg [2:0] state, state_n;
    
    reg [31:0] src_addr, src_addr_n;
    reg [31:0] dst_addr, dst_addr_n;
    reg [15:0] cnt, cnt_n;
    reg [3:0] wcnt, wcnt_n;
    
    reg arvalid,
                                rready,
                                awvalid,
                                wvalid,
                                wlast,
                                done;
    
    wire fifo_full,
                                fifo_empty;
    reg fifo_wren,
                                fifo_rden;
    wire [31:0] fifo_rdata;
    
    
    // it's desirable to code registers in a simple way
    always_ff @(posedge clk)
        if (!rst_n) begin
            state <= S_IDLE;
    
            src_addr <= 32'd0;
            dst_addr <= 32'd0;
            cnt <= 16'd0;
    
            wcnt <= 4'd0;
        end
        else begin
            state <= state_n;
    
            src_addr <= src_addr_n;
            dst_addr <= dst_addr_n;
            cnt <= cnt_n;
    
            wcnt <= wcnt_n;
        end
    
    
    // this block programs output values and next register values
    // based on states.
    always_comb begin
        // START:Please modify the code correctly.
        // START:Please modify the code correctly.
        // START:Please modify the code correctly.
        state_n = state; // Default to current state unless a transition condition is met
        src_addr_n = src_addr;
        dst_addr_n = dst_addr;
        cnt_n = cnt;
        wcnt_n = wcnt;
        arvalid = 0;
        awvalid = 0;
        wvalid = 0;
        rready = 0;
        fifo_wren = 0;
        fifo_rden = 0;
        done = 0;
        
        case (state)
            S_IDLE: begin
                done = 1'b1;
                if (start_i && byte_len_i != 16'd0) begin
                    src_addr_n = src_addr_i;
                    dst_addr_n = dst_addr_i;
                    cnt_n = byte_len_i;
                    state_n = S_RREQ;
                end
            end
            S_RREQ: begin
                arvalid = 1'b1;
                if (arready_i) begin
                    state_n = S_RDATA;
                    src_addr_n = src_addr + 'd4;
                end
            end
            S_RDATA: begin
                rready = 1'b1;
                if (rvalid_i) begin
                    fifo_wren = 1;
                    if (rlast_i) begin
                        state_n = S_WREQ;
                    end
                end
            end
            S_WREQ: begin
                awvalid = 1;
                if (awready_i) begin
                    dst_addr_n = dst_addr + 'd4;
                    state_n = S_WDATA;
                end
            end
            S_WDATA: begin
                wvalid = 1'b1;
                wlast = (wcnt =='d0);
                if (wready_i && !wlast) begin
                    fifo_rden = 1'b1;
                    state_n = S_WDATA;
                    wcnt_n = wcnt - 1;
                end
                if (wready_i && wvalid) begin
                    fifo_rden = 1'b1;
                    if (wcnt == 0) begin
                        if (wlast && cnt == 0) begin
                            state_n = S_IDLE;
                            done = 1;
                        end else begin
                            state_n = S_RREQ;
                        end
                    end
                end
            end
        endcase
    
        // END:Please modify the code correctly.
        // END:Please modify the code correctly.
        // END:Please modify the code correctly.
        // ********************** 
    end
    
    DMAC_FIFO u_fifo
    (
        .clk (clk),
        .rst_n (rst_n),
    
        .full_o (fifo_full),
        .wren_i (fifo_wren),
        .wdata_i (rdata_i),
    
        .empty_o (fifo_empty),
        .rden_i (fifo_rden),
        .rdata_o (fifo_rdata)
    );
    
    // Output assigments
    assign done_o = done;
    
    assign awid_o = 4'd0;
    assign awaddr_o = dst_addr;
    assign awlen_o = (cnt >= 'd64) ? 4'hF: cnt[5:2]-4'h1;
    assign awsize_o = 3'b010; // 4 bytes per transfer
    assign awburst_o = 2'b01; // incremental
    assign awvalid_o = awvalid;
    
    assign wid_o = 4'd0;
    assign wdata_o = fifo_rdata;
    assign wstrb_o = 4'b1111; // all bytes within 4 byte are valid
    assign wlast_o = wlast;
    assign wvalid_o = wvalid;
    
    assign bready_o = 1'b1;
    
    assign arvalid_o = arvalid;
    assign araddr_o = src_addr;
    assign arid_o = 4'd0;
    assign arlen_o = (cnt >= 'd64) ? 4'hF: cnt[5:2]-4'h1;
    assign arsize_o = 3'b010; // 4 bytes per transfer
    assign arburst_o = 2'b01; // incremental
    assign arvalid_o = arvalid;
    
    assign rready_o = rready & !fifo_full;
    

    endmodule <<EndOfFile:DMAC/RTL/DMAC_ENGINE.sv>>

    <<StartOfFile:DMAC/SIM/TB/DMAC_TOP_TB.sv>> define IP_VER 32'h000 define SRC_ADDR 32'h100 define DST_ADDR 32'h104 define LEN_ADDR 32'h108 define STAT_ADDR 32'h110 define START_ADDR 32'h10c

    `define TIMEOUT_CYCLE 999999 module DMAC_TOP_TB ();

    reg clk;
    reg rst_n;
    
    // clock generation
    initial begin
        clk = 1'b0;
    
        forever #10 clk = !clk;
    end
    
    // reset generation
    initial begin
        rst_n = 1'b0; // active at time 0
    
        repeat (3) @(posedge clk); // after 3 cycles,
        rst_n = 1'b1; // release the reset
    end
    
    // enable waveform dump
    initial begin
        \$dumpvars(0, u_DUT);
        \$dumpfile("dump.vcd");
    end
    

    // timeout initial begin #`TIMEOUT_CYCLE $display("Timeout!"); $finish; end

    APB apb_if (.clk(clk));
    
    AXI_AW_CH aw_ch (.clk(clk));
    AXI_W_CH w_ch (.clk(clk));
    AXI_B_CH b_ch (.clk(clk));
    AXI_AR_CH ar_ch (.clk(clk));
    AXI_R_CH r_ch (.clk(clk));
    
    task test_init();
        int data;
        apb_if.init();
    
        @(posedge rst_n); // wait for a release of the reset
        repeat (10) @(posedge clk); // wait another 10 cycles
    
        apb_if.read(`IP_VER, data);
        \$display("---------------------------------------------------");
        \$display("IP version: %x", data);
        \$display("---------------------------------------------------");
    
        \$display("---------------------------------------------------");
        \$display("Reset value test");
        \$display("---------------------------------------------------");
        apb_if.read(`SRC_ADDR, data);
        if (data===0)
            \$display("DMA_SRC(pass): %x", data);
        else begin
            \$display("DMA_SRC(fail): %x", data);
            @(posedge clk);
            \$finish;
        end
        apb_if.read(`DST_ADDR, data);
        if (data===0)
            \$display("DMA_DST(pass): %x", data);
        else begin
            \$display("DMA_DST(fail): %x", data);
            @(posedge clk);
            \$finish;
        end
        apb_if.read(`LEN_ADDR, data);
        if (data===0)
            \$display("DMA_LEN(pass): %x", data);
        else begin
            \$display("DMA_LEN(fail): %x", data);
            @(posedge clk);
            \$finish;
        end
        apb_if.read(`STAT_ADDR, data);
        if (data===1)
            \$display("DMA_STATUS(pass): %x", data);
        else begin
            \$display("DMA_STATUS(fail): %x", data);
            @(posedge clk);
            \$finish;
        end
    endtask
    
    task test_dma(input int src, input int dst, input int len);
        int data;
        int word;
        realtime elapsed_time;
    
        \$display("---------------------------------------------------");
        \$display("Load data to memory");
        \$display("---------------------------------------------------");
        for (int i=src; i<(src+len); i=i+4) begin
            word = \$random; 
            u_mem.write_word(i, word);
        end
    
        \$display("---------------------------------------------------");
        \$display("Configuration test");
        \$display("---------------------------------------------------");
        apb_if.write(`SRC_ADDR, src);
        apb_if.read(`SRC_ADDR, data);
        if (data===src)
            \$display("DMA_SRC(pass): %x", data);
        else begin
            \$display("DMA_SRC(fail): %x", data);
            @(posedge clk);
            \$finish;
        end
        apb_if.write(`DST_ADDR, dst);
        apb_if.read(`DST_ADDR, data);
        if (data===dst)
            \$display("DMA_DST(pass): %x", data);
        else begin
            \$display("DMA_DST(fail): %x", data);
            @(posedge clk);
            \$finish;
        end
        apb_if.write(`LEN_ADDR, len);
        apb_if.read(`LEN_ADDR, data);
        if (data===len)
            \$display("DMA_LEN(pass): %x", data);
        else begin
            \$display("DMA_LEN(fail): %x", data);
            @(posedge clk);
            \$finish;
        end
    
        \$display("---------------------------------------------------");
        \$display("DMA start");
        \$display("---------------------------------------------------");
        apb_if.write(`START_ADDR, 32'h1);
        elapsed_time = \$realtime;
    
        \$display("---------------------------------------------------");
        \$display("Wait for a DMA completion");
        \$display("---------------------------------------------------");
        data = 0;
        while (data!=1) begin
            apb_if.read(`STAT_ADDR, data);
            repeat (100) @(posedge clk);
        end
        @(posedge clk);
        elapsed_time = \$realtime - elapsed_time;
        \$timeformat(-9, 0, " ns", 10);
        \$display("Elapsed time for DMA: %t", elapsed_time);
    
        \$display("---------------------------------------------------");
        \$display("DMA completed");
        \$display("---------------------------------------------------");
    
        repeat (len) @(posedge clk); // to make sure data is written
    
        \$display("---------------------------------------------------");
        \$display("verify data");
        \$display("---------------------------------------------------");
        for (int i=0; i<len; i=i+4) begin
            logic [31:0] src_word;
            logic [31:0] dst_word;
            src_word = u_mem.read_word(src+i);
            dst_word = u_mem.read_word(dst+i);
            if (src_word!==dst_word) begin
                \$display("Mismatch! (src:%x @%x, dst:%x @%x", src_word, src+i, dst_word, dst+i);
            end
        end
    endtask
    
    int src,
                    dst,
                    len;
    
    // main
    initial begin
        test_init();
    
        src = 'h0000_1000;
        dst = 'h0000_2000;
        len = 'h0100;
        \$display("===================================================");
        \$display("= 1st trial"); 
        \$display("= Copying %x bytes from %x to %x", len, src, dst);
        \$display("===================================================");
        test_dma(src, dst, len);
    
        src = 'h1234_1234;
        dst = 'hABCD_ABCC;
        len = 'h0F00;
        \$display("===================================================");
        \$display("= 2nd trial (long transfer)");
        \$display("= Copying %x bytes from %x to %x", len, src, dst);
        \$display("===================================================");
        test_dma(src, dst, len);
    
        src = 'h4278_0000;
        dst = 'h4278_1000;
        len = 'h0F10;
        \$display("===================================================");
        \$display("= 3rd trial (long transfer-2)");
        \$display("= Copying %x bytes from %x to %x", len, src, dst);
        \$display("===================================================");
        test_dma(src, dst, len);
        \$finish;
    end
    
    
    AXI_SLAVE u_mem (
        .clk (clk),
        .rst_n (rst_n),
    
        .aw_ch (aw_ch),
        .w_ch (w_ch),
        .b_ch (b_ch),
        .ar_ch (ar_ch),
        .r_ch (r_ch)
    );
    
    DMAC_TOP u_DUT (
        .clk (clk),
        .rst_n (rst_n),
    
        // APB interface
        .psel_i (apb_if.psel),
        .penable_i (apb_if.penable),
        .paddr_i (apb_if.paddr[11:0]),
        .pwrite_i (apb_if.pwrite),
        .pwdata_i (apb_if.pwdata),
        .pready_o (apb_if.pready),
        .prdata_o (apb_if.prdata),
        .pslverr_o (apb_if.pslverr),
    
        // AXI AW channel
        .awid_o (aw_ch.awid),
        .awaddr_o (aw_ch.awaddr),
        .awlen_o (aw_ch.awlen),
        .awsize_o (aw_ch.awsize),
        .awburst_o (aw_ch.awburst),
        .awvalid_o (aw_ch.awvalid),
        .awready_i (aw_ch.awready),
    
        // AXI W channel
        .wid_o (w_ch.wid),
        .wdata_o (w_ch.wdata),
        .wstrb_o (w_ch.wstrb),
        .wlast_o (w_ch.wlast),
        .wvalid_o (w_ch.wvalid),
        .wready_i (w_ch.wready),
    
        // AXI B channel
        .bid_i (b_ch.bid),
        .bresp_i (b_ch.bresp),
        .bvalid_i (b_ch.bvalid),
        .bready_o (b_ch.bready),
    
        // AXI AR channel
        .arid_o (ar_ch.arid),
        .araddr_o (ar_ch.araddr),
        .arlen_o (ar_ch.arlen),
        .arsize_o (ar_ch.arsize),
        .arburst_o (ar_ch.arburst),
        .arvalid_o (ar_ch.arvalid),
        .arready_i (ar_ch.arready),
    
        // AXI R channel
        .rid_i (r_ch.rid),
        .rdata_i (r_ch.rdata),
        .rresp_i (r_ch.rresp),
        .rlast_i (r_ch.rlast),
        .rvalid_i (r_ch.rvalid),
        .rready_o (r_ch.rready)
    );
    

    endmodule <<EndOfFile:DMAC/SIM/TB/DMAC_TOP_TB.sv>>

    <StartOfFile:DMAC/RTL/DMAC_CFG.sv>> module DMAC_CFG ( input wire clk, input wire rst_n, // _n means active low

    // AMBA APB interface
    input wire psel_i,
    input wire penable_i,
    input wire [11:0] paddr_i,
    input wire pwrite_i,
    input wire [31:0] pwdata_i,
    output reg pready_o,
    output reg [31:0] prdata_o,
    output reg pslverr_o,
    
    // configuration registers
    output reg [31:0] src_addr_o,
    output reg [31:0] dst_addr_o,
    output reg [15:0] byte_len_o,
    output wire start_o,
    input wire done_i
    

    );

    // Configuration register to read/write
    reg [31:0] src_addr;
    reg [31:0] dst_addr;
    reg [15:0] byte_len;
    
    //----------------------------------------------------------
    // Write
    //----------------------------------------------------------
    // an APB write occurs when PSEL & PENABLE & PWRITE
    // clk : __--__--__--__--__--__--__--__--__--__--
    // psel : ___--------_____________________________
    // penable : _______----_____________________________
    // pwrite : ___--------_____________________________
    // wren : _______----_____________________________
    //
    // DMA start command must be asserted when APB writes 1 to the DMA_CMD
    // register
    // clk : __--__--__--__--__--__--__--__--__--__--
    // psel : ___--------_____________________________
    // penable : _______----_____________________________
    // pwrite : ___--------_____________________________
    // paddr : |DMA_CMD|
    // pwdata : | 1 |
    // start : _______----_____________________________
    
    wire wren = psel_i & penable_i & pwrite_i;
    
    always @(posedge clk) begin
        if (!rst_n) begin
            src_addr <= 32'd0;
            dst_addr <= 32'd0;
            byte_len <= 16'd0;
        end
        else if (wren) begin
            case (paddr_i)
                'h100: src_addr <= pwdata_i[31:0];
                'h104: dst_addr <= pwdata_i[31:0];
                'h108: byte_len <= pwdata_i[15:0];
            endcase
        end
    end
    wire start = wren & (paddr_i=='h10C) & pwdata_i[0];
    
    //----------------------------------------------------------
    // READ
    //----------------------------------------------------------
    // an APB read occurs when PSEL & PENABLE & !PWRITE
    // To make read data a direct output from register,
    // this code shall buffer the muxed read data into a register
    // in the SETUP cycle (PSEL & !PENABLE)
    // clk : __--__--__--__--__--__--__--__--__--__--
    // psel : ___--------_____________________________
    // penable : _______----_____________________________
    // pwrite : ________________________________________
    // reg update : ___----_________________________________
    // prdata : |DATA
    
    reg [31:0] rdata;
    
    always @(posedge clk) begin
        if (!rst_n) begin
            rdata <= 32'd0;
        end
        else if (psel_i & !penable_i & !pwrite_i) begin // in the setup cycle in the APB state diagram
            case (paddr_i)
                'h0: rdata <= 32'h0001_2024;
                'h100: rdata <= src_addr;
                'h104: rdata <= dst_addr;
                'h108: rdata <= {16'd0, byte_len};
                'h110: rdata <= {31'd0, done_i};
                default: rdata <= 32'd0;
            endcase
        end
    end
    
    // output assignments
    assign pready_o = 1'b1;
    assign prdata_o = rdata;
    assign pslverr_o = 1'b0;
    
    assign src_addr_o = src_addr;
    assign dst_addr_o = dst_addr;
    assign byte_len_o = byte_len;
    assign start_o = start;
    

    endmodule <<EndOfFile:DMAC/RTL/DMAC_CFG.sv>>

    <<StartOfFile:DMAC/RTL/DMAC_TOP.sv>> module DMAC_TOP ( input wire clk, input wire rst_n, // _n means active low

    // AMBA APB interface
    input wire psel_i,
    input wire penable_i,
    input wire [11:0] paddr_i,
    input wire pwrite_i,
    input wire [31:0] pwdata_i,
    output reg pready_o,
    output reg [31:0] prdata_o,
    output reg pslverr_o,
    
    // AMBA AXI interface (AW channel)
    output wire [3:0] awid_o,
    output wire [31:0] awaddr_o,
    output wire [3:0] awlen_o,
    output wire [2:0] awsize_o,
    output wire [1:0] awburst_o,
    output wire awvalid_o,
    input wire awready_i,
    
    // AMBA AXI interface (AW channel)
    output wire [3:0] wid_o,
    output wire [31:0] wdata_o,
    output wire [3:0] wstrb_o,
    output wire wlast_o,
    output wire wvalid_o,
    input wire wready_i,
    
    // AMBA AXI interface (B channel)
    input wire [3:0] bid_i,
    input wire [1:0] bresp_i,
    input wire bvalid_i,
    output wire bready_o,
    
    // AMBA AXI interface (AR channel)
    output wire [3:0] arid_o,
    output wire [31:0] araddr_o,
    output wire [3:0] arlen_o,
    output wire [2:0] arsize_o,
    output wire [1:0] arburst_o,
    output wire arvalid_o,
    input wire arready_i,
    
    // AMBA AXI interface (R channel)
    input wire [3:0] rid_i,
    input wire [31:0] rdata_i,
    input wire [1:0] rresp_i,
    input wire rlast_i,
    input wire rvalid_i,
    output wire rready_o
    

    );

    wire [31:0] src_addr;
    wire [31:0] dst_addr;
    wire [15:0] byte_len;
    wire start;
    wire done;
    
    DMAC_CFG u_cfg(
        .clk (clk),
        .rst_n (rst_n),
    
        // AMBA APB interface
        .psel_i (psel_i),
        .penable_i (penable_i),
        .paddr_i (paddr_i),
        .pwrite_i (pwrite_i),
        .pwdata_i (pwdata_i),
        .pready_o (pready_o),
        .prdata_o (prdata_o),
        .pslverr_o (pslverr_o),
    
        .src_addr_o (src_addr),
        .dst_addr_o (dst_addr),
        .byte_len_o (byte_len),
        .start_o (start),
        .done_i (done)
    );
    
    DMAC_ENGINE u_engine(
        .clk (clk),
        .rst_n (rst_n),
    
        // configuration registers
        .src_addr_i (src_addr),
        .dst_addr_i (dst_addr),
        .byte_len_i (byte_len),
        .start_i (start),
        .done_o (done),
    
        // AMBA AXI interface (AW channel)
        .awid_o (awid_o),
        .awaddr_o (awaddr_o),
        .awlen_o (awlen_o),
        .awsize_o (awsize_o),
        .awburst_o (awburst_o),
        .awvalid_o (awvalid_o),
        .awready_i (awready_i),
    
        // AMBA AXI interface (W channel)
        .wid_o (wid_o),
        .wdata_o (wdata_o),
        .wstrb_o (wstrb_o),
        .wlast_o (wlast_o),
        .wvalid_o (wvalid_o),
        .wready_i (wready_i),
    
        // AMBA AXI interface (B channel)
        .bid_i (bid_i),
        .bresp_i (bresp_i),
        .bvalid_i (bvalid_i),
        .bready_o (bready_o),
    
        // AMBA AXI interface (AR channel)
        .arid_o (arid_o),
        .araddr_o (araddr_o),
        .arlen_o (arlen_o),
        .arsize_o (arsize_o),
        .arburst_o (arburst_o),
        .arvalid_o (arvalid_o),
        .arready_i (arready_i),
    
        // AMBA AXI interface (R channel)
        .rid_i (rid_i),
        .rdata_i (rdata_i),
        .rresp_i (rresp_i),
        .rlast_i (rlast_i),
        .rvalid_i (rvalid_i),
        .rready_o (rready_o)
    );
    

    endmodule <<EndOfFile:DMAC/RTL/DMAC_TOP.sv>>

    <<StartOfFile:DMAC/SIM/TB/AXI_INTF.sv>> `include "../TB/AXI_TYPEDEF.svh"

    interface AXI_AW_CH #( parameter ADDR_WIDTH = AXI_ADDR_WIDTH, parameter ID_WIDTH = AXI_ID_WIDTH ) ( input clk ); logic awvalid; logic awready; logic [ID_WIDTH-1:0] awid; logic [ADDR_WIDTH-1:0] awaddr; logic [3:0] awlen; logic [2:0] awsize; logic [1:0] awburst;

    endinterface

    interface AXI_W_CH #( parameter DATA_WIDTH = AXI_DATA_WIDTH, parameter ID_WIDTH = AXI_ID_WIDTH ) ( input clk ); logic wvalid; logic wready; logic [ID_WIDTH-1:0] wid; logic [DATA_WIDTH-1:0] wdata; logic [DATA_WIDTH/8-1:0] wstrb; logic wlast;

    endinterface

    interface AXI_B_CH #( parameter ID_WIDTH = `AXI_ID_WIDTH ) ( input clk ); logic bvalid; logic bready; logic [ID_WIDTH-1:0] bid; logic [1:0] bresp;

    endinterface

    interface AXI_AR_CH #( parameter ADDR_WIDTH = AXI_ADDR_WIDTH, parameter ID_WIDTH = AXI_ID_WIDTH ) ( input clk ); logic arvalid; logic arready; logic [ID_WIDTH-1:0] arid; logic [ADDR_WIDTH-1:0] araddr; logic [3:0] arlen; logic [2:0] arsize; logic [1:0] arburst;

    endinterface

    interface AXI_R_CH #( parameter DATA_WIDTH = AXI_DATA_WIDTH, parameter ID_WIDTH = AXI_ID_WIDTH ) ( input clk ); logic rvalid; logic rready; logic [ID_WIDTH-1:0] rid; logic [DATA_WIDTH-1:0] rdata; logic [1:0] rresp; logic rlast;

    endinterface

    interface APB ( input clk ); logic psel; logic penable; logic [31:0] paddr; logic pwrite; logic [31:0] pwdata; logic pready; logic [31:0] prdata; logic pslverr;

    modport master (
        input clk,
        input pready, prdata, pslverr,
        output psel, penable, paddr, pwrite, pwdata
    );
    
    task init();
        psel = 1'b0;
        penable = 1'b0;
        paddr = 32'd0;
        pwrite = 1'b0;
        pwdata = 32'd0;
    endtask
    
    task write(input int addr,
               input int data);
        #1
        psel = 1'b1;
        penable = 1'b0;
        paddr = addr;
        pwrite = 1'b1;
        pwdata = data;
        @(posedge clk);
        #1
        penable = 1'b1;
        @(posedge clk);
    
        while (pready==1'b0) begin
            @(posedge clk);
        end
    
        psel = 1'b0;
        penable = 1'b0;
        paddr = 'hX;
        pwrite = 1'bx;
        pwdata = 'hX;
    endtask
    
    task read(input int addr,
              output int data);
        #1
        psel = 1'b1;
        penable = 1'b0;
        paddr = addr;
        pwrite = 1'b0;
        pwdata = 'hX;
        @(posedge clk);
        #1
        penable = 1'b1;
        @(posedge clk);
    
        while (pready==1'b0) begin
            @(posedge clk);
        end
        data = prdata;
    
        psel = 1'b0;
        penable = 1'b0;
        paddr = 'hX;
        pwrite = 1'bx;
        pwdata = 'hX;
    endtask
    

    endinterface <<EndOfFile:DMAC/SIM/TB/AXI_INTF.sv>>

    <<StartOfFile:DMAC/SIM/TB/AXI_SLAVE.sv>> `include "../TB/AXI_TYPEDEF.svh"

    module AXI_SLAVE #( parameter ADDR_WIDTH = 16, parameter DATA_WIDTH = AXI_DATA_WIDTH, parameter ID_WIDTH = AXI_ID_WIDTH, parameter AWREADY_DELAY = 1, parameter ARREADY_DELAY = 1, parameter AR2R_DELAY = 50 ) ( input wire clk, input wire rst_n, // _n means active low

    AXI_AW_CH aw_ch,
    AXI_W_CH w_ch,
    AXI_B_CH b_ch,
    AXI_AR_CH ar_ch,
    AXI_R_CH r_ch
    

    );

    localparam DATA_DEPTH = 1<<ADDR_WIDTH;
    
    logic [7:0] mem[DATA_DEPTH];
    
    function void write_byte(int addr, input bit [7:0] wdata);
        mem[addr] = wdata;
    endfunction
    
    function void write_word(int addr, input bit [31:0] wdata);
        for (int i=0; i<4; i++) begin
            write_byte(addr+i, wdata[8*i +: 8]); // [i*8+7:i*8]
        end
    endfunction
    
    function bit [7:0] read_byte(int addr);
        read_byte = mem[addr];
    endfunction
    
    function bit [31:0] read_word(int addr);
        for (int i=0; i<4; i++) begin
            read_word[8*i +: 8] = read_byte(addr+i);// [i*8+7:i*8]
        end
    endfunction
    
    //----------------------------------------------------------
    // write channels (AW, W, B)
    //----------------------------------------------------------
    localparam logic [1:0] S_W_IDLE = 0,
                                S_W_AWREADY = 1,
                                S_W_BURST = 2,
                                S_W_RESP = 3;
    
    logic [1:0] wstate, wstate_n;
    logic [7:0] wcnt, wcnt_n;
    
    logic [ADDR_WIDTH-1:0] waddr, waddr_n;
    logic [ID_WIDTH-1:0] wid, wid_n;
    logic [3:0] wlen, wlen_n;
    
    always_ff @(posedge clk)
        if (!rst_n) begin
            wstate <= S_W_IDLE;
    
            wcnt <= 8'd0;
            waddr <= {ADDR_WIDTH{1'b0}};
            wid <= {ID_WIDTH{1'b0}};
            wlen <= 4'd0;
        end
        else begin
            wstate <= wstate_n;
    
            wcnt <= wcnt_n;
            waddr <= waddr_n;
            wid <= wid_n;
            wlen <= wlen_n;
        end
    
    always @(*) begin
        wstate_n = wstate;
    
        wcnt_n = wcnt;
        waddr_n = waddr;
        wid_n = wid;
        wlen_n = wlen;
    
        aw_ch.awready = 1'b0;
        w_ch.wready = 1'b0;
        b_ch.bvalid = 1'b0;
    
        case (wstate)
            S_W_IDLE: begin
                if (aw_ch.awvalid) begin
                    if (AWREADY_DELAY == 0) begin
                        waddr_n = aw_ch.awaddr;
                        wid_n = aw_ch.awid;
                        wlen_n = aw_ch.awlen;
                        aw_ch.awready = 1'b1;
                        wstate_n = S_W_BURST;
                    end
                    else begin
                        wcnt_n = AWREADY_DELAY-1;
                        wstate_n = S_W_AWREADY;
                    end
                end
            end
            S_W_AWREADY: begin
                if (wcnt==0) begin
                    waddr_n = aw_ch.awaddr;
                    wid_n = aw_ch.awid;
                    wlen_n = aw_ch.awlen;
                    aw_ch.awready = 1'b1;
                    wstate_n = S_W_BURST;
                end
                else begin
                    wcnt_n = wcnt - 8'd1;
                end
            end
            S_W_BURST: begin
                w_ch.wready = 1'b1;
                if (w_ch.wvalid) begin
                    for (int i=0; i<DATA_WIDTH/8; i++) begin
                        write_byte(waddr + i, w_ch.wdata[i*8 +: 8]); // [i*8+7:i*8]
                    end
                    waddr_n = waddr + (DATA_WIDTH/8);
                    if (wlen==4'd0) begin
                        wstate_n = S_W_RESP;
                    end
                    else begin
                        wlen_n = wlen - 4'd1;
                    end
                end
            end
            S_W_RESP: begin
                b_ch.bvalid = 1'b1;
                if (b_ch.bready) begin
                    wstate_n = S_W_IDLE;
                end
            end
        endcase
    end
    
    //----------------------------------------------------------
    // read channel (AR, R)
    //----------------------------------------------------------
    localparam logic [1:0] S_R_IDLE = 0,
                                S_R_ARREADY = 1,
                                S_R_DELAY = 2,
                                S_R_BURST = 3;
    
    logic [1:0] rstate, rstate_n;
    logic [7:0] rcnt, rcnt_n;
    
    logic [ADDR_WIDTH-1:0] raddr, raddr_n;
    logic [ID_WIDTH-1:0] rid, rid_n;
    logic [3:0] rlen, rlen_n;
    
    always_ff @(posedge clk)
        if (!rst_n) begin
            rstate <= S_R_IDLE;
    
            rcnt <= 8'd0;
            raddr <= {ADDR_WIDTH{1'b0}};
            rid <= {ID_WIDTH{1'b0}};
            rlen <= 4'd0;
        end
        else begin
            rstate <= rstate_n;
    
            rcnt <= rcnt_n;
            raddr <= raddr_n;
            rid <= rid_n;
            rlen <= rlen_n;
        end
    
    always_comb begin
        rstate_n = rstate;
    
        rcnt_n = rcnt;
        raddr_n = raddr;
        rid_n = rid;
        rlen_n = rlen;
    
        ar_ch.arready = 1'b0;
        r_ch.rvalid = 1'b0;
        r_ch.rlast = 1'b0;
    
        case (rstate)
            S_R_IDLE: begin
                if (ar_ch.arvalid) begin
                    if (ARREADY_DELAY == 0) begin
                        raddr_n = ar_ch.araddr;
                        rid_n = ar_ch.arid;
                        rlen_n = ar_ch.arlen;
                        ar_ch.arready = 1'b1;
    
                        rcnt_n = AR2R_DELAY - 1;
                        rstate_n = S_R_DELAY;
                    end
                    else begin
                        rcnt_n = ARREADY_DELAY-1;
                        rstate_n = S_R_ARREADY;
                    end
                end
            end
            S_R_ARREADY: begin
                if (rcnt==0) begin
                    raddr_n = ar_ch.araddr;
                    rid_n = ar_ch.arid;
                    rlen_n = ar_ch.arlen;
                    ar_ch.arready = 1'b1;
    
                    rcnt_n = AR2R_DELAY - 1;
                    rstate_n = S_R_DELAY;
                end
                else begin
                    rcnt_n = rcnt - 8'd1;
                end
            end
            S_R_DELAY: begin
                if (rcnt==0) begin
                    rstate_n = S_R_BURST;
                end
                else begin
                    rcnt_n = rcnt - 8'd1;
                end
            end
            S_R_BURST: begin
                r_ch.rvalid = 1'b1;
                r_ch.rlast = (rlen==4'd0);
                for (int i=0; i<DATA_WIDTH/8; i++) begin
                    r_ch.rdata[i*8 +: 8] = read_byte(raddr + i); // [i*8+7:i*8]
                end
                if (r_ch.rready) begin
                    raddr_n = raddr + (DATA_WIDTH/8);
                    if (rlen==4'd0) begin
                        rstate_n = S_R_IDLE;
                    end
                    else begin
                        rlen_n = rlen - 4'd1;
                    end
                end
            end
        endcase
    end
    
    // output assignments
    assign b_ch.bid = wid;
    assign b_ch.bresp = 2'd0;
    assign r_ch.rid = rid;
    assign r_ch.rresp = 2'd0;
    

    endmodule <<EndOfFile:DMAC/SIM/TB/AXI_SLAVE.sv>>

    <<StartOfFile:DMAC/SIM/TB/AXI_TYPEDEF.svh>> ifndef __AXI_TYPEDEF_SVH__ define AXI_TYPEDEF_SVH

    define AXI_ADDR_WIDTH 32 define AXI_DATA_WIDTH 32 `define AXI_ID_WIDTH 4

    `endif /* AXI_TYPEDEF_SVH */ <<EndOfFile:DMAC/SIM/TB/AXI_TYPEDEF.svh>>

    Please verify if the following table is correct using the code provided below.

    +-------+-------------------------------------------------------------------------------------+------------+-----------------------------------------------------------+-----------------------------------------+ | State | Major outputs | Next State | Next state transition condition | Notes | | +---------+--------+---------------------------------------+-------------------+------+ | | | | | ARVALID | RREADY | AWVALID | WVALID | done | | | | +-------+---------+--------+---------------------------------------+-------------------+------+------------+-----------------------------------------------------------+-----------------------------------------+ | IDLE | 0 | 0 | 0 | 0 | 1 | RREQ | (DMA_CMD.start is written as 1) and (DMA_LEN.byte_len!=0) | On moving out, | | | | | | | | | | - Copy DMA_SRC to SRC_ADDR. | | | | | | | | | | - Copy DMA_DST to DST_ADDR | | | | | | | | | | - Copy DMA_LEN to the internal counter | +-------+---------+--------+---------------------------------------+-------------------+------+------------+-----------------------------------------------------------+-----------------------------------------+ | RREQ | 1 | 0 | 0 | 0 | 0 | RDATA | ARREADY=1 | On moving out, | | | | | | | | | | - Increment ARADDR by 4 | | | | | | | | | | | | | | | | | | | | ARLEN = (cnt>=64) ? 'hF : cnt[5:2]-4'h1 | +-------+---------+--------+---------------------------------------+-------------------+------+------------+-----------------------------------------------------------+-----------------------------------------+ | RDATA | 0 | 1 | 0 | 0 | 0 | WREQ | (RVALID=1) & (RLAST) | Push data to FIFO | | | | | | | +------------+-----------------------------------------------------------+-----------------------------------------+ | | | | | | | RDATA | (RVALID) & (!RLAST) | Push data to FIFO | +-------+---------+--------+---------------------------------------+-------------------+------+------------+-----------------------------------------------------------+-----------------------------------------+ | WREQ | 0 | 0 | 1 | 0 | 0 | WDATA | AWREADY=1 | On moving out, | | | | | AWLEN=(cnt>=64) ? 'hF : cnt[5:2]-4'h1 | | | | | - Increment AWADDR by 4 | | | | | | | | | | - Decrement the internal counter by 4 | +-------+---------+--------+---------------------------------------+-------------------+------+------------+-----------------------------------------------------------+-----------------------------------------+ | WDATA | 0 | 0 | 0 | 1 | 0 | RREQ | (WREADY=1) (!WLAST) & (counter!=0) | Pop data from FIFO | | | | | | WLAST=(wcnt=='d0) | | | | Decrement wcnt | | | | | | | +------------+-----------------------------------------------------------+-----------------------------------------+ | | | | | | | IDLE | (WREADY=1) (WLAST) & (counter==0) | Pop data from FIFO | +-------+---------+--------+---------------------------------------+-------------------+------+------------+-----------------------------------------------------------+-----------------------------------------+

    Direct Memory Access (DMA) Controller Design Document V1.0

    1 Overview This document specifies the design and implementation of a Direct Memory Access Controller (DMAC) as a part of System-on-a-Chip (SoC). The main purpose of this DMAC design is to integrate into SoC for exchange a large volume of data between memory and peripherals at high speed. The proposed DMAC works on ARM’s Advanced Microcontroller Bus Architecture (AMBA) specification. The DMAC provides an AMBA APB interface to configure the IP, and an AMBA AXI interface to transfer data.

    2 Architecture Specification 2.1 General Description Some applications require transferring a volume of data between memory and peripherals without any modification on data. In software, it is commonly served by executing the memcpy library function in C, C++ or other languages. In C, the function has the following interface and copies len bytes from the object pointed by src to the object pointed by dst: void* memcpy(void* dst, const void* src, size_t len). While a pure software-based implementation of memcpy transfers data using CPU instructions, DMA does not use expensive CPU cycles but uses a hardware engine (DMAC) for the transfer. This can significantly speed up data transfers and allows using CPU for other jobs. 2.2 Usage Constraints Below describe constraints in utilizing DMAC v1. -The src and dst addresses are physical addresses. -The src and dst addresses must be a multiple of 4. -The len must be a multiple of 4. -The maximum len is 0xFFFF -Source and destination ranges must not overlap. 2.3 Programming Model Software can use the following sequence to transfer data using DMAC. -1.Write the source address to DMA_SRC register -2.Write the destination address to DMA_DST register -3.Write length to DMA_LEN register -4.Write 1 to bit[0] of DMA_CMD register -5.Wait until DMA_STATUS register has bit[0] as 1.

    2.4 Register Map In order to control DMAC, software can configure the following registers. +--------+------------+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+---+---+---+---+---+---+---+---+---+-------+ | Offset | Reg Name | 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | +--------+------------+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+---+---+---+---+---+---+---+---+---+-------+ | 0x00 | DMA_VER | version | +--------+------------+---------------------------------------------------------------------------------------------------------------------------------------------------------+ | 0x04~0xFC | Reserved | +--------+------------+---------------------------------------------------------------------------------------------------------------------------------------------------------+ | 0x100 | DMA_SRC | start_addr | +--------+------------+---------------------------------------------------------------------------------------------------------------------------------------------------------+ | 0x104 | DMA_DST | start_addr | +--------+------------+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+-------------------------------------------------------------------------+ | 0x108 | DMA_LEN | | | | | | | | | | | | | | | | | byte_len | +--------+------------+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+---+---+---+---+---+---+---+---+---+-------+ | 0x10C | DMA_CMD | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | start | +--------+------------+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+---+---+---+---+---+---+---+---+---+-------+ | 0x110 | DMA_STATUS | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | done | +--------+------------+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+---+---+---+---+---+---+---+---+---+-------+

    2.4.1 DMA VERSION

    Field nameBit rangeR/WReset valueDesciption
    version[31:0]R0x0001_2024The version of this DMA controller. The upper 16 bits represent the major version. The lower 16 bits represent the released year of the version. This document describes behaviors of major version 1.

    2.4.2 DMA_SRC

    Field nameBit rangeR/WReset valueDesciption
    start_addr[31:0]R/W0x0000_0000start address of the source range.

    2.4.3 DMA_DST

    Field nameBit rangeR/WReset valueDesciption
    start_addr[31:0]R/W0x0000_0000start address of the destination range.

    2.4.4 DMA_LEN

    Field nameBit rangeR/WReset valueDesciption
    byte_len[15:0]R/W0x0000Number of bytes to be transferred from the source to the destination.

    2.4.5 DMA_CMD Field

    Field nameBit rangeR/WReset valueDesciption
    start[0]WN/AWriting 1 to this field will initiate a DMA transfer based on DMA_SRC, DMA_DST, and DMA_LEN registers. Software must not write 1 when there’s an on-going transfer. Writing 0 to this field does not affect operation

    2.4.6 DMA_STATUS

    Field nameBit rangeR/WReset valueDesciption
    done[0]R1This field is 1 when there’s no on-going DMA transfer. Software must wait this field to be 1 for a completion of a transfer. Software must not initiate a DMA transfer when this field is 0.

    3 Micro-architecture v1.1 Specification This section describes microarchitecture of a simple DMAC. It reads data from memory, buffers the data, and write the data into memory. It repeats this procedure until it completes transferring the specified number of bytes. For simplicity, it read/writes one-cycle data (4 bytes) at a time (in other words, burst-1 transfers). For simplicity, this microarchitecture does not consider write responses from the AXI interface. Later versions will support burst transfers and write responses.

    3.1 External Interface DMAC v1.1 has the following external interfaces to communicate with other hardware IPs. -AMBA APB interface for configuration -AMBA AXI interface for data transfer

    The image you’ve uploaded is a diagram showing the on-chip interconnect of a computer system. Here’s a detailed description: The diagram illustrates how the CPU core, memory, and DMAC (Direct Memory Access Controller) are connected through an on-chip interconnect. The connections also include specific interfaces like Config interface (APB) and Data interface (AXI). “CPU core” is a box on the left side connected to the central “On-chip interconnect” cloud shape with a bidirectional arrow. Below the “CPU core,” there’s another box labeled “Memory,” also connected to the “On-chip interconnect” with a bidirectional arrow. On the right side, there’s a box labeled “DMAC” connected to both “Config interface (APB)” and “Data interface (AXI)” which are in turn connected to the central “On-chip interconnect” with bidirectional arrows. The arrows indicate that data can flow in both directions between these components.

    3.2 Block Diagram DMAC v1.1 has the following blocks inside.

    The diagram is divided into three main blocks labeled “DMAC_TOP,” “DMAC_CFG,” and “DMAC_ENGINE.” “clk” and “rst” are inputs to the “DMAC_TOP” block. An arrow labeled “APB” connects the “DMAC_TOP” block to the “DMAC_CFG” block. Another arrow labeled “AXI” connects both the “DMAC_TOP” and “DMAC_CFG” blocks to the “DMAC_ENGINE” block. Inside the “DMAC_ENGINE” block, there are four internal components labeled as follows: SRC_ADDR DST_ADDR CNT DATA BUF There’s also a small circular graph with nodes labeled 0 to 3 inside this block. This diagram is likely used to illustrate the flow of data or control signals between these components in a Direct Memory Access Controller configuration. Please let me know if you need more information!

    3.3 Configuration Register (lab2) This block receives read/write requests from the APB and configures the registers describes in Section 2.4.

    3.4 Finite State Machine (lab3) DMA engine utilizes the following state machine to control operations.

    The diagram contains five blue circles representing different states: IDLE, RREQ, RDATA, WREQ, and WDATA. Arrows connect these circles indicating the flow from one state to another. Each arrow has text annotations that describe the conditions for transitioning from one state to another. For example, transitioning from IDLE to RREQ requires writing 1 to DMA_CMD & LEN!=0, and copying DMA_SRC/DST/LEN. There are also annotations on the state circles themselves, such as “done=1” on IDLE and “AWVALID=1” on WDATA.

    +-------+--------------------------------------------+------------+-----------------------------------------------------------+----------------------------------------+ | State | Major outputs | Next State | Next state transition condition | Notes | | +---------+--------+---------+--------+------+ | | | | | ARVALID | RREADY | AWVALID | WVALID | done | | | | +-------+---------+--------+---------+--------+------+------------+-----------------------------------------------------------+----------------------------------------+ | IDLE | 0 | 0 | 0 | 0 | 1 | RREQ | (DMA_CMD.start is written as 1) and (DMA_LEN.byte_len!=0) | On moving out, | | | | | | | | | | - Copy DMA_SRC to SRC_ADDR. | | | | | | | | | | - Copy DMA_DST to DST_ADDR | | | | | | | | | | - Copy DMA_LEN to the internal counter | +-------+---------+--------+---------+--------+------+------------+-----------------------------------------------------------+----------------------------------------+ | RREQ | 1 | 0 | 0 | 0 | 0 | RDATA | ARREADY=1 | On moving out, | | | | | | | | | | - Increment ARADDR by 4 | +-------+---------+--------+---------+--------+------+------------+-----------------------------------------------------------+----------------------------------------+ | RDATA | 0 | 1 | 0 | 0 | 0 | WREQ | RVALID=1 | On moving out, | | | | | | | | | | - Buffer RDATA into the data buffer | +-------+---------+--------+---------+--------+------+------------+-----------------------------------------------------------+----------------------------------------+ | WREQ | 0 | 0 | 1 | 0 | 0 | WDATA | AWREADY=1 | On moving out, | | | | | | | | | | - Increment AWADDR by 4 | | | | | | | | | | - Decrement the internal counter by 4 | +-------+---------+--------+---------+--------+------+------------+-----------------------------------------------------------+----------------------------------------+ | WDATA | 0 | 0 | 0 | 1 | 0 | RREQ | (WREADY=1) & (counter!=0) | | | | | | | | +------------+-----------------------------------------------------------+----------------------------------------+ | | | | | | | IDLE | (WREADY=1) & (counter==0) | | +-------+---------+--------+---------+--------+------+------------+-----------------------------------------------------------+----------------------------------------+

    { "signal": [ { "name": "clk", "wave": "p....|.........." }, { "name": "state", "wave": "2.3.4|..5.6.2...", "data": ["IDLE", "RREQ", "RDATA", "WREQ", "WDATA", "IDLE"] }, { "name": "write to CMD", "wave": "010..|..........", "data": ["1"] }, {}, [ "AR ch", { "name": "ARVALID(out)", "wave": "0.1.0|..........", "data": ["SRC"] }, { "name": "ARADDR(out)", "wave": "x.3.x|..........", "data": ["SRC"] }, { "name": "ARLEN(out)", "wave": "2....|..........", "data": ["0"] }, { "name": "ARREADY(in)", "wave": "0..10|.........." }, ], [ "R ch", { "name": "RREADY(out)", "wave": "0...1|..0......." }, { "name": "RVALID(in)", "wave": "0....|.10......." }, { "name": "RDATA(in)", "wave": "x....|.4x.......", "data": ["DATA"] }, ], [ "AW ch", { "name": "AWVALID(out)", "wave": "0....|..1.0....." }, { "name": "AWADDR(out)", "wave": "x....|..5.x.....", "data": ["DST"] }, { "name": "AWLEN(out)", "wave": "2....|..........", "data": ["0"] }, { "name": "AWREADY(in)", "wave": "0....|...10....." }, ], [ "W ch", { "name": "WVALID(out)", "wave": "0....|....1.0..." }, { "name": "WDATA(out)", "wave": "x....|....4.x...", "data": ["DATA"] }, { "name": "WREADY(in)", "wave": "0....|.....10..." } ] ], "head" : { "tick" : "0" }, "foot" : { "tick" : "0" } } 그림 1. DMA operation with microarchitecture v1.1

    4 Micro-architecture v1.2 Specification (lab4) A problem with microarchitecture v1.1 is that it reads/writes data one-by-one. As memory read takes some time, DMAC v1.1 will suffer from poor performance with a long memory read latency (그림 2). We will improve the microarchitecture to transfer a burst of data to minimize performance degradation.

    { "signal": [ { "name": "clk", "wave": "p....|.................." }, { "name": "state", "wave": "2.3.4|..5.6.3.4|..5.6.3.", "data": ["IDLE", "RREQ", "RDATA", "WREQ", "WDATA", "RREQ", "RDATA", "WREQ", "WDATA", "RREQ"] }, { "name": "write to CMD", "wave": "010..|.........|........", "data": ["1"] }, {}, [ "AR ch", { "name": "ARVALID(out)", "wave": "0.1.0|......1.0|......1.", "data": ["SRC"] }, { "name": "ARADDR(out)", "wave": "x.3.x|......3.x|......3.", "data": ["SRC", "SRC+4", "SRC+8"] }, { "name": "ARLEN(out)", "wave": "2....|.........|........", "data": ["0"] }, { "name": "ARREADY(in)", "wave": "0..10|.......10|.......1" }, ], [ "R ch", { "name": "RREADY(out)", "wave": "0...1|..0.....1|..0....." }, { "name": "RVALID(in)", "wave": "0....|.10......|.10....." }, { "name": "RDATA(in)", "wave": "x....|.4x......|.4x.....", "data": ["DATA", "DATA"] }, ], [ "AW ch", { "name": "AWVALID(out)", "wave": "0....|..1.0....|..1.0..." }, { "name": "AWADDR(out)", "wave": "x....|..5.x....|..5.x...", "data": ["DST", "DST+4"] }, { "name": "AWLEN(out)", "wave": "2....|.........|........", "data": ["0"] }, { "name": "AWREADY(in)", "wave": "0....|...10....|...10..." }, ], [ "W ch", { "name": "WVALID(out)", "wave": "0....|....1.0..|....1.0." }, { "name": "WDATA(out)", "wave": "x....|....4.x..|....4.x.", "data": ["DATA", "DATA"] }, { "name": "WREADY(in)", "wave": "0....|.....10..|.....10." } ] ], "head" : { "tick" : "0" }, "foot" : { "tick" : "0" } } 그림 2. DMA operation with microarchitecture 1.1. At a time, it transfers single burst of data In Microarchitecture version 2, DMAC transfers up to 16 cycles of data with a single access. This can significantly reduce execution time by transferring data in bursts (그림 3).

  4. Assistant

    Based on the provided code snippets, diagrams, and state tables, your document details a DMA Controller (DMAC) system designed to transfer data efficiently between the source and destination in a computational system using Direct Memory Access (DMA). Below is a verification of the state transition table according to the described DMA operation logic provided in your document.

    Verified State Transition Table:

    StateARVALIDRREADYAWVALIDWVALIDdoneNext StateNext State Transition ConditionNotes
    IDLE00001RREQDMA_CMD.start = 1 && DMA_LEN.byte_len != 0- Copy DMA_SRC to SRC_ADDR. - Copy DMA_DST to DST_ADDR. - Copy DMA_LEN to the internal counter.
    RREQ10000RDATAARREADY = 1- Increment ARADDR by 4. - ARLEN is calculated based on cnt.
    RDATA01000WREQ(RVALID = 1) & (RLAST)Push data to FIFO.
    RDATA(RVALID) & (!RLAST)Push data to FIFO.
    WREQ00100WDATAAWREADY = 1- Increment AWADDR by 4. - Decrement the internal counter by 4. - AWLEN is calculated based on cnt.
    WDATA00010RREQ(WREADY = 1) (!WLAST) & (counter != 0)Pop data from FIFO. - Decrement wcnt.
    IDLE(WREADY = 1) (WLAST) & (counter == 0)Pop data from FIFO.

    Observations:

    1. State Transition Consistency: The state transitions are logically consistent and well-defined for operations of a DMA controller aimed at efficient data handling, matching with operations outlined in Figure 1 and 3 of your document.

    2. Transition Conditions: Transition conditions are clearly specified for each state, ensuring the DMA operation can be followed accurately as expected.

    3. Action on Transitions: Notes and actions on moving from one state to another are well annotated, contributing to the understanding of operations at each stage of the DMA process.

    4. Usage of FIFO: The table along with the detailed description indicates the use of a FIFO buffering method for managing the data before writing it to the destination, which aligns with the need for efficiency in DMA operations.

    5. Efficiency through Burst Transfers: The document's narrative around transitioning to burst transfers for efficiency aligns with the table's logic, especially in the sequence of operations depicted in the DMA engine's state machine.

    Based on the information given and the analysis of the provided state transition table, everything appears correctly structured to reflect the operation of a DMA controller that uses single-cycle and burst transfer methods for efficiency. This structured operation would theoretically improve data transfer rates significantly while offloading work from the CPU, as described in Microarchitecture versions 1.1 and 1.2.

  5. User

    Modify the code to utilize FIFO using fifo_full, fifo_empty, fifo_wren, and fifo_rden Please fix the modifiable code in the file "DMAC/RTL/DMAC_ENGINE.sv" by modifying it.

    <<StartOfFile:DMAC/RTL/DMAC_ENGINE.sv>> module DMAC_ENGINE ( input wire clk, input wire rst_n, // _n means active low

    // configuration registers
    input wire [31:0] src_addr_i,
    input wire [31:0] dst_addr_i,
    input wire [15:0] byte_len_i,
    input wire start_i,
    output wire done_o,
    
    // AMBA AXI interface (AW channel)
    output wire [3:0] awid_o,
    output wire [31:0] awaddr_o,
    output wire [3:0] awlen_o,
    output wire [2:0] awsize_o,
    output wire [1:0] awburst_o,
    output wire awvalid_o,
    input wire awready_i,
    
    // AMBA AXI interface (W channel)
    output wire [3:0] wid_o,
    output wire [31:0] wdata_o,
    output wire [3:0] wstrb_o,
    output wire wlast_o,
    output wire wvalid_o,
    input wire wready_i,
    
    // AMBA AXI interface (B channel)
    input wire [3:0] bid_i,
    input wire [1:0] bresp_i,
    input wire bvalid_i,
    output wire bready_o,
    
    // AMBA AXI interface (AR channel)
    output wire [3:0] arid_o,
    output wire [31:0] araddr_o,
    output wire [3:0] arlen_o,
    output wire [2:0] arsize_o,
    output wire [1:0] arburst_o,
    output wire arvalid_o,
    input wire arready_i,
    
    // AMBA AXI interface (R channel)
    input wire [3:0] rid_i,
    input wire [31:0] rdata_i,
    input wire [1:0] rresp_i,
    input wire rlast_i,
    input wire rvalid_i,
    output wire rready_o
    

    );

    // mnemonics for state values
    localparam S_IDLE = 3'd0,
                                S_RREQ = 3'd1,
                                S_RDATA = 3'd2,
                                S_WREQ = 3'd3,
                                S_WDATA = 3'd4;
    
    reg [2:0] state, state_n;
    
    reg [31:0] src_addr, src_addr_n;
    reg [31:0] dst_addr, dst_addr_n;
    reg [15:0] cnt, cnt_n;
    reg [3:0] wcnt, wcnt_n;
    
    reg arvalid,
                                rready,
                                awvalid,
                                wvalid,
                                wlast,
                                done;
    
    wire fifo_full,
                                fifo_empty;
    reg fifo_wren,
                                fifo_rden;
    wire [31:0] fifo_rdata;
    
    
    // it's desirable to code registers in a simple way
    always_ff @(posedge clk)
        if (!rst_n) begin
            state <= S_IDLE;
    
            src_addr <= 32'd0;
            dst_addr <= 32'd0;
            cnt <= 16'd0;
    
            wcnt <= 4'd0;
        end
        else begin
            state <= state_n;
    
            src_addr <= src_addr_n;
            dst_addr <= dst_addr_n;
            cnt <= cnt_n;
    
            wcnt <= wcnt_n;
        end
    
    
    // this block programs output values and next register values
    // based on states.
    always_comb begin
        // START:Please modify the code correctly.
        // START:Please modify the code correctly.
        // START:Please modify the code correctly.
        state_n = state; // Default to current state unless a transition condition is met
        src_addr_n = src_addr;
        dst_addr_n = dst_addr;
        cnt_n = cnt;
        wcnt_n = wcnt;
        arvalid = 0;
        awvalid = 0;
        wvalid = 0;
        rready = 0;
        fifo_wren = 0;
        fifo_rden = 0;
        done = 0;
        
        case (state)
            S_IDLE: begin
                done = 1'b1;
                if (start_i && byte_len_i != 16'd0) begin
                    src_addr_n = src_addr_i;
                    dst_addr_n = dst_addr_i;
                    cnt_n = byte_len_i;
                    state_n = S_RREQ;
                end
            end
            S_RREQ: begin
                arvalid = 1'b1;
                if (arready_i) begin
                    state_n = S_RDATA;
                    src_addr_n = src_addr + 'd4;
                end
            end
            S_RDATA: begin
                rready = 1'b1;
                if (rvalid_i) begin
                    fifo_wren = 1;
                    if (rlast_i) begin
                        state_n = S_WREQ;
                    end
                end
            end
            S_WREQ: begin
                awvalid = 1;
                if (awready_i) begin
                    dst_addr_n = dst_addr + 'd4;
                    state_n = S_WDATA;
                end
            end
            S_WDATA: begin
                wvalid = 1'b1;
                wlast = (wcnt =='d0);
                if (wready_i && !wlast) begin
                    fifo_rden = 1'b1;
                    state_n = S_WDATA;
                    wcnt_n = wcnt - 1;
                end
                if (wready_i && wvalid) begin
                    fifo_rden = 1'b1;
                    if (wcnt == 0) begin
                        if (wlast && cnt == 0) begin
                            state_n = S_IDLE;
                            done = 1;
                        end else begin
                            state_n = S_RREQ;
                        end
                    end
                end
            end
        endcase
    
        // END:Please modify the code correctly.
        // END:Please modify the code correctly.
        // END:Please modify the code correctly.
        // ********************** 
    end
    
    DMAC_FIFO u_fifo
    (
        .clk (clk),
        .rst_n (rst_n),
    
        .full_o (fifo_full),
        .wren_i (fifo_wren),
        .wdata_i (rdata_i),
    
        .empty_o (fifo_empty),
        .rden_i (fifo_rden),
        .rdata_o (fifo_rdata)
    );
    
    // Output assigments
    assign done_o = done;
    
    assign awid_o = 4'd0;
    assign awaddr_o = dst_addr;
    assign awlen_o = (cnt >= 'd64) ? 4'hF: cnt[5:2]-4'h1;
    assign awsize_o = 3'b010; // 4 bytes per transfer
    assign awburst_o = 2'b01; // incremental
    assign awvalid_o = awvalid;
    
    assign wid_o = 4'd0;
    assign wdata_o = fifo_rdata;
    assign wstrb_o = 4'b1111; // all bytes within 4 byte are valid
    assign wlast_o = wlast;
    assign wvalid_o = wvalid;
    
    assign bready_o = 1'b1;
    
    assign arvalid_o = arvalid;
    assign araddr_o = src_addr;
    assign arid_o = 4'd0;
    assign arlen_o = (cnt >= 'd64) ? 4'hF: cnt[5:2]-4'h1;
    assign arsize_o = 3'b010; // 4 bytes per transfer
    assign arburst_o = 2'b01; // incremental
    assign arvalid_o = arvalid;
    
    assign rready_o = rready & !fifo_full;
    

    endmodule <<EndOfFile:DMAC/RTL/DMAC_ENGINE.sv>>

    { "signal": [ { "name": "clk", "wave": "p....|....|.......|....." }, { "name": "state", "wave": "2.3.4|....|..5.6..|..3.4", "data": ["IDLE", "RREQ", "RDATA", "WREQ", "WDATA", "RREQ"] }, { "name": "write to CMD", "wave": "010..|....|.......|.....", "data": ["1"] }, {}, [ "AR ch", { "name": "ARVALID(out)", "wave": "0.1.0|....|.......|.....", "data": ["SRC"] }, { "name": "ARADDR(out)", "wave": "x.3.x|....|.......|.....", "data": ["SRC"] }, { "name": "ARLEN(out)", "wave": "2....|....|.......|.....", "data": ["15"] }, { "name": "ARREADY(in)", "wave": "0..10|....|.......|....." }, ], [ "R ch", { "name": "RREADY(out)", "wave": "0...1|....|..0....|....." }, { "name": "RVALID(in)", "wave": "0....|.1..|..0....|....." }, { "name": "RLAST(in)", "wave": "0....|....|.10....|....." }, { "name": "RDATA(in)", "wave": "x....|.444|44x....|.....", "data": ["D0", "D1", "D2", "D14", "D15"] }, ], [ "AW ch", { "name": "AWVALID(out)", "wave": "0....|....|..1.0..|....." }, { "name": "AWADDR(out)", "wave": "x....|....|..5.x..|.....", "data": ["DST"] }, { "name": "AWLEN(out)", "wave": "2....|....|.......|.....", "data": ["15"] }, { "name": "AWREADY(in)", "wave": "0....|....|...10..|....." }, ], [ "W ch", { "name": "WVALID(out)", "wave": "0....|....|....1..|..0.." }, { "name": "WDATA(out)", "wave": "x....|....|....444|44x..", "data": ["D0", "D1", "D2", "D14", "D15"] }, { "name": "WLAST(out)", "wave": "0....|....|.......|.10.." }, { "name": "WREADY(in)", "wave": "0....|....|....1..|..0.." } ] ], "head" : { "tick" : "0" }, "foot" : { "tick" : "0" } } 그림 3. DMA operation with burst transfers. At a time, a request reads/writes 16 cycles of data.

    Please verify if the following table is correct using the code provided below.

    +-------+-------------------------------------------------------------------------------------+------------+-----------------------------------------------------------+-----------------------------------------+ | State | Major outputs | Next State | Next state transition condition | Notes | | +---------+--------+---------------------------------------+-------------------+------+ | | | | | ARVALID | RREADY | AWVALID | WVALID | done | | | | +-------+---------+--------+---------------------------------------+-------------------+------+------------+-----------------------------------------------------------+-----------------------------------------+ | IDLE | 0 | 0 | 0 | 0 | 1 | RREQ | (DMA_CMD.start is written as 1) and (DMA_LEN.byte_len!=0) | On moving out, | | | | | | | | | | - Copy DMA_SRC to SRC_ADDR. | | | | | | | | | | - Copy DMA_DST to DST_ADDR | | | | | | | | | | - Copy DMA_LEN to the internal counter | +-------+---------+--------+---------------------------------------+-------------------+------+------------+-----------------------------------------------------------+-----------------------------------------+ | RREQ | 1 | 0 | 0 | 0 | 0 | RDATA | ARREADY=1 | On moving out, | | | | | | | | | | - Increment ARADDR by 4 | | | | | | | | | | | | | | | | | | | | ARLEN = (cnt>=64) ? 'hF : cnt[5:2]-4'h1 | +-------+---------+--------+---------------------------------------+-------------------+------+------------+-----------------------------------------------------------+-----------------------------------------+ | RDATA | 0 | 1 | 0 | 0 | 0 | WREQ | (RVALID=1) & (RLAST) | Push data to FIFO | | | | | | | +------------+-----------------------------------------------------------+-----------------------------------------+ | | | | | | | RDATA | (RVALID) & (!RLAST) | Push data to FIFO | +-------+---------+--------+---------------------------------------+-------------------+------+------------+-----------------------------------------------------------+-----------------------------------------+ | WREQ | 0 | 0 | 1 | 0 | 0 | WDATA | AWREADY=1 | On moving out, | | | | | AWLEN=(cnt>=64) ? 'hF : cnt[5:2]-4'h1 | | | | | - Increment AWADDR by 4 | | | | | | | | | | - Decrement the internal counter by 4 | +-------+---------+--------+---------------------------------------+-------------------+------+------------+-----------------------------------------------------------+-----------------------------------------+ | WDATA | 0 | 0 | 0 | 1 | 0 | RREQ | (WREADY=1) (!WLAST) & (counter!=0) | Pop data from FIFO | | | | | | WLAST=(wcnt=='d0) | | | | Decrement wcnt | | | | | | | +------------+-----------------------------------------------------------+-----------------------------------------+ | | | | | | | IDLE | (WREADY=1) (WLAST) & (counter==0) | Pop data from FIFO | +-------+---------+--------+---------------------------------------+-------------------+------+------------+-----------------------------------------------------------+-----------------------------------------+

    <<StartOfFile:DMAC/RTL/DMAC_FIFO.sv>> module DMAC_FIFO #( parameter DEPTH_LG2 = 4, parameter DATA_WIDTH = 32 ) ( input wire clk, input wire rst_n,

    output wire full_o,
    input wire wren_i,
    input wire [DATA_WIDTH-1:0] wdata_i,
    
    output wire empty_o,
    input wire rden_i,
    output wire [DATA_WIDTH-1:0] rdata_o
    

    );

    localparam FIFO_DEPTH = (1<<DEPTH_LG2);
    
    reg [DATA_WIDTH-1:0] data[FIFO_DEPTH];
    
    reg full, full_n,
                                        empty, empty_n;
    reg [DEPTH_LG2:0] wrptr, wrptr_n,
                                        rdptr, rdptr_n;
    
    // reset entries to all 0s
    always_ff @(posedge clk)
        if (!rst_n) begin
            full <= 1'b0;
            empty <= 1'b1; // empty after as reset
    
            wrptr <= {(DEPTH_LG2+1){1'b0}};
            rdptr <= {(DEPTH_LG2+1){1'b0}};
    
            for (int i=0; i<FIFO_DEPTH; i++) begin
                data[i] <= {DATA_WIDTH{1'b0}};
            end
        end
        else begin
            full <= full_n;
            empty <= empty_n;
    
            wrptr <= wrptr_n;
            rdptr <= rdptr_n;
    
            if (wren_i) begin
                data[wrptr[DEPTH_LG2-1:0]] <= wdata_i;
            end
        end
    
    always_comb begin
        wrptr_n = wrptr;
        rdptr_n = rdptr;
    
        if (wren_i) begin
            wrptr_n = wrptr + 'd1;
        end
    
        if (rden_i) begin
            rdptr_n = rdptr + 'd1;
        end
    
        empty_n = (wrptr_n == rdptr_n);
        full_n = (wrptr_n[DEPTH_LG2]!=rdptr_n[DEPTH_LG2])
                                     &(wrptr_n[DEPTH_LG2-1:0]==rdptr_n[DEPTH_LG2-1:0]);
    
    end
    
    // synthesis translate_off
    always @(posedge clk) begin
        if (full_o & wren_i) begin
            \$display("FIFO overflow");
            @(posedge clk);
            \$finish;
        end
    end
    
    always @(posedge clk) begin
        if (empty_o & rden_i) begin
            \$display("FIFO underflow");
            @(posedge clk);
            \$finish;
        end
    end
    // synthesis translate_on
    
    assign full_o = full;
    assign empty_o = empty;
    assign rdata_o = data[rdptr[DEPTH_LG2-1:0]];
    

    endmodule <<EndOfFile:DMAC/RTL/DMAC_FIFO.sv>>

    <<StartOfFile:DMAC/SIM/TB/DMAC_TOP_TB.sv>> define IP_VER 32'h000 define SRC_ADDR 32'h100 define DST_ADDR 32'h104 define LEN_ADDR 32'h108 define STAT_ADDR 32'h110 define START_ADDR 32'h10c

    `define TIMEOUT_CYCLE 999999 module DMAC_TOP_TB ();

    reg clk;
    reg rst_n;
    
    // clock generation
    initial begin
        clk = 1'b0;
    
        forever #10 clk = !clk;
    end
    
    // reset generation
    initial begin
        rst_n = 1'b0; // active at time 0
    
        repeat (3) @(posedge clk); // after 3 cycles,
        rst_n = 1'b1; // release the reset
    end
    
    // enable waveform dump
    initial begin
        \$dumpvars(0, u_DUT);
        \$dumpfile("dump.vcd");
    end
    

    // timeout initial begin #`TIMEOUT_CYCLE $display("Timeout!"); $finish; end

    APB apb_if (.clk(clk));
    
    AXI_AW_CH aw_ch (.clk(clk));
    AXI_W_CH w_ch (.clk(clk));
    AXI_B_CH b_ch (.clk(clk));
    AXI_AR_CH ar_ch (.clk(clk));
    AXI_R_CH r_ch (.clk(clk));
    
    task test_init();
        int data;
        apb_if.init();
    
        @(posedge rst_n); // wait for a release of the reset
        repeat (10) @(posedge clk); // wait another 10 cycles
    
        apb_if.read(`IP_VER, data);
        \$display("---------------------------------------------------");
        \$display("IP version: %x", data);
        \$display("---------------------------------------------------");
    
        \$display("---------------------------------------------------");
        \$display("Reset value test");
        \$display("---------------------------------------------------");
        apb_if.read(`SRC_ADDR, data);
        if (data===0)
            \$display("DMA_SRC(pass): %x", data);
        else begin
            \$display("DMA_SRC(fail): %x", data);
            @(posedge clk);
            \$finish;
        end
        apb_if.read(`DST_ADDR, data);
        if (data===0)
            \$display("DMA_DST(pass): %x", data);
        else begin
            \$display("DMA_DST(fail): %x", data);
            @(posedge clk);
            \$finish;
        end
        apb_if.read(`LEN_ADDR, data);
        if (data===0)
            \$display("DMA_LEN(pass): %x", data);
        else begin
            \$display("DMA_LEN(fail): %x", data);
            @(posedge clk);
            \$finish;
        end
        apb_if.read(`STAT_ADDR, data);
        if (data===1)
            \$display("DMA_STATUS(pass): %x", data);
        else begin
            \$display("DMA_STATUS(fail): %x", data);
            @(posedge clk);
            \$finish;
        end
    endtask
    
    task test_dma(input int src, input int dst, input int len);
        int data;
        int word;
        realtime elapsed_time;
    
        \$display("---------------------------------------------------");
        \$display("Load data to memory");
        \$display("---------------------------------------------------");
        for (int i=src; i<(src+len); i=i+4) begin
            word = \$random; 
            u_mem.write_word(i, word);
        end
    
        \$display("---------------------------------------------------");
        \$display("Configuration test");
        \$display("---------------------------------------------------");
        apb_if.write(`SRC_ADDR, src);
        apb_if.read(`SRC_ADDR, data);
        if (data===src)
            \$display("DMA_SRC(pass): %x", data);
        else begin
            \$display("DMA_SRC(fail): %x", data);
            @(posedge clk);
            \$finish;
        end
        apb_if.write(`DST_ADDR, dst);
        apb_if.read(`DST_ADDR, data);
        if (data===dst)
            \$display("DMA_DST(pass): %x", data);
        else begin
            \$display("DMA_DST(fail): %x", data);
            @(posedge clk);
            \$finish;
        end
        apb_if.write(`LEN_ADDR, len);
        apb_if.read(`LEN_ADDR, data);
        if (data===len)
            \$display("DMA_LEN(pass): %x", data);
        else begin
            \$display("DMA_LEN(fail): %x", data);
            @(posedge clk);
            \$finish;
        end
    
        \$display("---------------------------------------------------");
        \$display("DMA start");
        \$display("---------------------------------------------------");
        apb_if.write(`START_ADDR, 32'h1);
        elapsed_time = \$realtime;
    
        \$display("---------------------------------------------------");
        \$display("Wait for a DMA completion");
        \$display("---------------------------------------------------");
        data = 0;
        while (data!=1) begin
            apb_if.read(`STAT_ADDR, data);
            repeat (100) @(posedge clk);
        end
        @(posedge clk);
        elapsed_time = \$realtime - elapsed_time;
        \$timeformat(-9, 0, " ns", 10);
        \$display("Elapsed time for DMA: %t", elapsed_time);
    
        \$display("---------------------------------------------------");
        \$display("DMA completed");
        \$display("---------------------------------------------------");
    
        repeat (len) @(posedge clk); // to make sure data is written
    
        \$display("---------------------------------------------------");
        \$display("verify data");
        \$display("---------------------------------------------------");
        for (int i=0; i<len; i=i+4) begin
            logic [31:0] src_word;
            logic [31:0] dst_word;
            src_word = u_mem.read_word(src+i);
            dst_word = u_mem.read_word(dst+i);
            if (src_word!==dst_word) begin
                \$display("Mismatch! (src:%x @%x, dst:%x @%x", src_word, src+i, dst_word, dst+i);
            end
        end
    endtask
    
    int src,
                    dst,
                    len;
    
    // main
    initial begin
        test_init();
    
        src = 'h0000_1000;
        dst = 'h0000_2000;
        len = 'h0100;
        \$display("===================================================");
        \$display("= 1st trial"); 
        \$display("= Copying %x bytes from %x to %x", len, src, dst);
        \$display("===================================================");
        test_dma(src, dst, len);
    
        src = 'h1234_1234;
        dst = 'hABCD_ABCC;
        len = 'h0F00;
        \$display("===================================================");
        \$display("= 2nd trial (long transfer)");
        \$display("= Copying %x bytes from %x to %x", len, src, dst);
        \$display("===================================================");
        test_dma(src, dst, len);
    
        src = 'h4278_0000;
        dst = 'h4278_1000;
        len = 'h0F10;
        \$display("===================================================");
        \$display("= 3rd trial (long transfer-2)");
        \$display("= Copying %x bytes from %x to %x", len, src, dst);
        \$display("===================================================");
        test_dma(src, dst, len);
        \$finish;
    end
    
    
    AXI_SLAVE u_mem (
        .clk (clk),
        .rst_n (rst_n),
    
        .aw_ch (aw_ch),
        .w_ch (w_ch),
        .b_ch (b_ch),
        .ar_ch (ar_ch),
        .r_ch (r_ch)
    );
    
    DMAC_TOP u_DUT (
        .clk (clk),
        .rst_n (rst_n),
    
        // APB interface
        .psel_i (apb_if.psel),
        .penable_i (apb_if.penable),
        .paddr_i (apb_if.paddr[11:0]),
        .pwrite_i (apb_if.pwrite),
        .pwdata_i (apb_if.pwdata),
        .pready_o (apb_if.pready),
        .prdata_o (apb_if.prdata),
        .pslverr_o (apb_if.pslverr),
    
        // AXI AW channel
        .awid_o (aw_ch.awid),
        .awaddr_o (aw_ch.awaddr),
        .awlen_o (aw_ch.awlen),
        .awsize_o (aw_ch.awsize),
        .awburst_o (aw_ch.awburst),
        .awvalid_o (aw_ch.awvalid),
        .awready_i (aw_ch.awready),
    
        // AXI W channel
        .wid_o (w_ch.wid),
        .wdata_o (w_ch.wdata),
        .wstrb_o (w_ch.wstrb),
        .wlast_o (w_ch.wlast),
        .wvalid_o (w_ch.wvalid),
        .wready_i (w_ch.wready),
    
        // AXI B channel
        .bid_i (b_ch.bid),
        .bresp_i (b_ch.bresp),
        .bvalid_i (b_ch.bvalid),
        .bready_o (b_ch.bready),
    
        // AXI AR channel
        .arid_o (ar_ch.arid),
        .araddr_o (ar_ch.araddr),
        .arlen_o (ar_ch.arlen),
        .arsize_o (ar_ch.arsize),
        .arburst_o (ar_ch.arburst),
        .arvalid_o (ar_ch.arvalid),
        .arready_i (ar_ch.arready),
    
        // AXI R channel
        .rid_i (r_ch.rid),
        .rdata_i (r_ch.rdata),
        .rresp_i (r_ch.rresp),
        .rlast_i (r_ch.rlast),
        .rvalid_i (r_ch.rvalid),
        .rready_o (r_ch.rready)
    );
    

    endmodule <<EndOfFile:DMAC/SIM/TB/DMAC_TOP_TB.sv>>

    <StartOfFile:DMAC/RTL/DMAC_CFG.sv>> module DMAC_CFG ( input wire clk, input wire rst_n, // _n means active low

    // AMBA APB interface
    input wire psel_i,
    input wire penable_i,
    input wire [11:0] paddr_i,
    input wire pwrite_i,
    input wire [31:0] pwdata_i,
    output reg pready_o,
    output reg [31:0] prdata_o,
    output reg pslverr_o,
    
    // configuration registers
    output reg [31:0] src_addr_o,
    output reg [31:0] dst_addr_o,
    output reg [15:0] byte_len_o,
    output wire start_o,
    input wire done_i
    

    );

    // Configuration register to read/write
    reg [31:0] src_addr;
    reg [31:0] dst_addr;
    reg [15:0] byte_len;
    
    //----------------------------------------------------------
    // Write
    //----------------------------------------------------------
    // an APB write occurs when PSEL & PENABLE & PWRITE
    // clk : __--__--__--__--__--__--__--__--__--__--
    // psel : ___--------_____________________________
    // penable : _______----_____________________________
    // pwrite : ___--------_____________________________
    // wren : _______----_____________________________
    //
    // DMA start command must be asserted when APB writes 1 to the DMA_CMD
    // register
    // clk : __--__--__--__--__--__--__--__--__--__--
    // psel : ___--------_____________________________
    // penable : _______----_____________________________
    // pwrite : ___--------_____________________________
    // paddr : |DMA_CMD|
    // pwdata : | 1 |
    // start : _______----_____________________________
    
    wire wren = psel_i & penable_i & pwrite_i;
    
    always @(posedge clk) begin
        if (!rst_n) begin
            src_addr <= 32'd0;
            dst_addr <= 32'd0;
            byte_len <= 16'd0;
        end
        else if (wren) begin
            case (paddr_i)
                'h100: src_addr <= pwdata_i[31:0];
                'h104: dst_addr <= pwdata_i[31:0];
                'h108: byte_len <= pwdata_i[15:0];
            endcase
        end
    end
    wire start = wren & (paddr_i=='h10C) & pwdata_i[0];
    
    //----------------------------------------------------------
    // READ
    //----------------------------------------------------------
    // an APB read occurs when PSEL & PENABLE & !PWRITE
    // To make read data a direct output from register,
    // this code shall buffer the muxed read data into a register
    // in the SETUP cycle (PSEL & !PENABLE)
    // clk : __--__--__--__--__--__--__--__--__--__--
    // psel : ___--------_____________________________
    // penable : _______----_____________________________
    // pwrite : ________________________________________
    // reg update : ___----_________________________________
    // prdata : |DATA
    
    reg [31:0] rdata;
    
    always @(posedge clk) begin
        if (!rst_n) begin
            rdata <= 32'd0;
        end
        else if (psel_i & !penable_i & !pwrite_i) begin // in the setup cycle in the APB state diagram
            case (paddr_i)
                'h0: rdata <= 32'h0001_2024;
                'h100: rdata <= src_addr;
                'h104: rdata <= dst_addr;
                'h108: rdata <= {16'd0, byte_len};
                'h110: rdata <= {31'd0, done_i};
                default: rdata <= 32'd0;
            endcase
        end
    end
    
    // output assignments
    assign pready_o = 1'b1;
    assign prdata_o = rdata;
    assign pslverr_o = 1'b0;
    
    assign src_addr_o = src_addr;
    assign dst_addr_o = dst_addr;
    assign byte_len_o = byte_len;
    assign start_o = start;
    

    endmodule <<EndOfFile:DMAC/RTL/DMAC_CFG.sv>>

    <<StartOfFile:DMAC/RTL/DMAC_TOP.sv>> module DMAC_TOP ( input wire clk, input wire rst_n, // _n means active low

    // AMBA APB interface
    input wire psel_i,
    input wire penable_i,
    input wire [11:0] paddr_i,
    input wire pwrite_i,
    input wire [31:0] pwdata_i,
    output reg pready_o,
    output reg [31:0] prdata_o,
    output reg pslverr_o,
    
    // AMBA AXI interface (AW channel)
    output wire [3:0] awid_o,
    output wire [31:0] awaddr_o,
    output wire [3:0] awlen_o,
    output wire [2:0] awsize_o,
    output wire [1:0] awburst_o,
    output wire awvalid_o,
    input wire awready_i,
    
    // AMBA AXI interface (AW channel)
    output wire [3:0] wid_o,
    output wire [31:0] wdata_o,
    output wire [3:0] wstrb_o,
    output wire wlast_o,
    output wire wvalid_o,
    input wire wready_i,
    
    // AMBA AXI interface (B channel)
    input wire [3:0] bid_i,
    input wire [1:0] bresp_i,
    input wire bvalid_i,
    output wire bready_o,
    
    // AMBA AXI interface (AR channel)
    output wire [3:0] arid_o,
    output wire [31:0] araddr_o,
    output wire [3:0] arlen_o,
    output wire [2:0] arsize_o,
    output wire [1:0] arburst_o,
    output wire arvalid_o,
    input wire arready_i,
    
    // AMBA AXI interface (R channel)
    input wire [3:0] rid_i,
    input wire [31:0] rdata_i,
    input wire [1:0] rresp_i,
    input wire rlast_i,
    input wire rvalid_i,
    output wire rready_o
    

    );

    wire [31:0] src_addr;
    wire [31:0] dst_addr;
    wire [15:0] byte_len;
    wire start;
    wire done;
    
    DMAC_CFG u_cfg(
        .clk (clk),
        .rst_n (rst_n),
    
        // AMBA APB interface
        .psel_i (psel_i),
        .penable_i (penable_i),
        .paddr_i (paddr_i),
        .pwrite_i (pwrite_i),
        .pwdata_i (pwdata_i),
        .pready_o (pready_o),
        .prdata_o (prdata_o),
        .pslverr_o (pslverr_o),
    
        .src_addr_o (src_addr),
        .dst_addr_o (dst_addr),
        .byte_len_o (byte_len),
        .start_o (start),
        .done_i (done)
    );
    
    DMAC_ENGINE u_engine(
        .clk (clk),
        .rst_n (rst_n),
    
        // configuration registers
        .src_addr_i (src_addr),
        .dst_addr_i (dst_addr),
        .byte_len_i (byte_len),
        .start_i (start),
        .done_o (done),
    
        // AMBA AXI interface (AW channel)
        .awid_o (awid_o),
        .awaddr_o (awaddr_o),
        .awlen_o (awlen_o),
        .awsize_o (awsize_o),
        .awburst_o (awburst_o),
        .awvalid_o (awvalid_o),
        .awready_i (awready_i),
    
        // AMBA AXI interface (W channel)
        .wid_o (wid_o),
        .wdata_o (wdata_o),
        .wstrb_o (wstrb_o),
        .wlast_o (wlast_o),
        .wvalid_o (wvalid_o),
        .wready_i (wready_i),
    
        // AMBA AXI interface (B channel)
        .bid_i (bid_i),
        .bresp_i (bresp_i),
        .bvalid_i (bvalid_i),
        .bready_o (bready_o),
    
        // AMBA AXI interface (AR channel)
        .arid_o (arid_o),
        .araddr_o (araddr_o),
        .arlen_o (arlen_o),
        .arsize_o (arsize_o),
        .arburst_o (arburst_o),
        .arvalid_o (arvalid_o),
        .arready_i (arready_i),
    
        // AMBA AXI interface (R channel)
        .rid_i (rid_i),
        .rdata_i (rdata_i),
        .rresp_i (rresp_i),
        .rlast_i (rlast_i),
        .rvalid_i (rvalid_i),
        .rready_o (rready_o)
    );
    

    endmodule <<EndOfFile:DMAC/RTL/DMAC_TOP.sv>>

    <<StartOfFile:DMAC/SIM/TB/AXI_INTF.sv>> `include "../TB/AXI_TYPEDEF.svh"

    interface AXI_AW_CH #( parameter ADDR_WIDTH = AXI_ADDR_WIDTH, parameter ID_WIDTH = AXI_ID_WIDTH ) ( input clk ); logic awvalid; logic awready; logic [ID_WIDTH-1:0] awid; logic [ADDR_WIDTH-1:0] awaddr; logic [3:0] awlen; logic [2:0] awsize; logic [1:0] awburst;

    endinterface

    interface AXI_W_CH #( parameter DATA_WIDTH = AXI_DATA_WIDTH, parameter ID_WIDTH = AXI_ID_WIDTH ) ( input clk ); logic wvalid; logic wready; logic [ID_WIDTH-1:0] wid; logic [DATA_WIDTH-1:0] wdata; logic [DATA_WIDTH/8-1:0] wstrb; logic wlast;

    endinterface

    interface AXI_B_CH #( parameter ID_WIDTH = `AXI_ID_WIDTH ) ( input clk ); logic bvalid; logic bready; logic [ID_WIDTH-1:0] bid; logic [1:0] bresp;

    endinterface

    interface AXI_AR_CH #( parameter ADDR_WIDTH = AXI_ADDR_WIDTH, parameter ID_WIDTH = AXI_ID_WIDTH ) ( input clk ); logic arvalid; logic arready; logic [ID_WIDTH-1:0] arid; logic [ADDR_WIDTH-1:0] araddr; logic [3:0] arlen; logic [2:0] arsize; logic [1:0] arburst;

    endinterface

    interface AXI_R_CH #( parameter DATA_WIDTH = AXI_DATA_WIDTH, parameter ID_WIDTH = AXI_ID_WIDTH ) ( input clk ); logic rvalid; logic rready; logic [ID_WIDTH-1:0] rid; logic [DATA_WIDTH-1:0] rdata; logic [1:0] rresp; logic rlast;

    endinterface

    interface APB ( input clk ); logic psel; logic penable; logic [31:0] paddr; logic pwrite; logic [31:0] pwdata; logic pready; logic [31:0] prdata; logic pslverr;

    modport master (
        input clk,
        input pready, prdata, pslverr,
        output psel, penable, paddr, pwrite, pwdata
    );
    
    task init();
        psel = 1'b0;
        penable = 1'b0;
        paddr = 32'd0;
        pwrite = 1'b0;
        pwdata = 32'd0;
    endtask
    
    task write(input int addr,
               input int data);
        #1
        psel = 1'b1;
        penable = 1'b0;
        paddr = addr;
        pwrite = 1'b1;
        pwdata = data;
        @(posedge clk);
        #1
        penable = 1'b1;
        @(posedge clk);
    
        while (pready==1'b0) begin
            @(posedge clk);
        end
    
        psel = 1'b0;
        penable = 1'b0;
        paddr = 'hX;
        pwrite = 1'bx;
        pwdata = 'hX;
    endtask
    
    task read(input int addr,
              output int data);
        #1
        psel = 1'b1;
        penable = 1'b0;
        paddr = addr;
        pwrite = 1'b0;
        pwdata = 'hX;
        @(posedge clk);
        #1
        penable = 1'b1;
        @(posedge clk);
    
        while (pready==1'b0) begin
            @(posedge clk);
        end
        data = prdata;
    
        psel = 1'b0;
        penable = 1'b0;
        paddr = 'hX;
        pwrite = 1'bx;
        pwdata = 'hX;
    endtask
    

    endinterface <<EndOfFile:DMAC/SIM/TB/AXI_INTF.sv>>

    <<StartOfFile:DMAC/SIM/TB/AXI_SLAVE.sv>> `include "../TB/AXI_TYPEDEF.svh"

    module AXI_SLAVE #( parameter ADDR_WIDTH = 16, parameter DATA_WIDTH = AXI_DATA_WIDTH, parameter ID_WIDTH = AXI_ID_WIDTH, parameter AWREADY_DELAY = 1, parameter ARREADY_DELAY = 1, parameter AR2R_DELAY = 50 ) ( input wire clk, input wire rst_n, // _n means active low

    AXI_AW_CH aw_ch,
    AXI_W_CH w_ch,
    AXI_B_CH b_ch,
    AXI_AR_CH ar_ch,
    AXI_R_CH r_ch
    

    );

    localparam DATA_DEPTH = 1<<ADDR_WIDTH;
    
    logic [7:0] mem[DATA_DEPTH];
    
    function void write_byte(int addr, input bit [7:0] wdata);
        mem[addr] = wdata;
    endfunction
    
    function void write_word(int addr, input bit [31:0] wdata);
        for (int i=0; i<4; i++) begin
            write_byte(addr+i, wdata[8*i +: 8]); // [i*8+7:i*8]
        end
    endfunction
    
    function bit [7:0] read_byte(int addr);
        read_byte = mem[addr];
    endfunction
    
    function bit [31:0] read_word(int addr);
        for (int i=0; i<4; i++) begin
            read_word[8*i +: 8] = read_byte(addr+i);// [i*8+7:i*8]
        end
    endfunction
    
    //----------------------------------------------------------
    // write channels (AW, W, B)
    //----------------------------------------------------------
    localparam logic [1:0] S_W_IDLE = 0,
                                S_W_AWREADY = 1,
                                S_W_BURST = 2,
                                S_W_RESP = 3;
    
    logic [1:0] wstate, wstate_n;
    logic [7:0] wcnt, wcnt_n;
    
    logic [ADDR_WIDTH-1:0] waddr, waddr_n;
    logic [ID_WIDTH-1:0] wid, wid_n;
    logic [3:0] wlen, wlen_n;
    
    always_ff @(posedge clk)
        if (!rst_n) begin
            wstate <= S_W_IDLE;
    
            wcnt <= 8'd0;
            waddr <= {ADDR_WIDTH{1'b0}};
            wid <= {ID_WIDTH{1'b0}};
            wlen <= 4'd0;
        end
        else begin
            wstate <= wstate_n;
    
            wcnt <= wcnt_n;
            waddr <= waddr_n;
            wid <= wid_n;
            wlen <= wlen_n;
        end
    
    always @(*) begin
        wstate_n = wstate;
    
        wcnt_n = wcnt;
        waddr_n = waddr;
        wid_n = wid;
        wlen_n = wlen;
    
        aw_ch.awready = 1'b0;
        w_ch.wready = 1'b0;
        b_ch.bvalid = 1'b0;
    
        case (wstate)
            S_W_IDLE: begin
                if (aw_ch.awvalid) begin
                    if (AWREADY_DELAY == 0) begin
                        waddr_n = aw_ch.awaddr;
                        wid_n = aw_ch.awid;
                        wlen_n = aw_ch.awlen;
                        aw_ch.awready = 1'b1;
                        wstate_n = S_W_BURST;
                    end
                    else begin
                        wcnt_n = AWREADY_DELAY-1;
                        wstate_n = S_W_AWREADY;
                    end
                end
            end
            S_W_AWREADY: begin
                if (wcnt==0) begin
                    waddr_n = aw_ch.awaddr;
                    wid_n = aw_ch.awid;
                    wlen_n = aw_ch.awlen;
                    aw_ch.awready = 1'b1;
                    wstate_n = S_W_BURST;
                end
                else begin
                    wcnt_n = wcnt - 8'd1;
                end
            end
            S_W_BURST: begin
                w_ch.wready = 1'b1;
                if (w_ch.wvalid) begin
                    for (int i=0; i<DATA_WIDTH/8; i++) begin
                        write_byte(waddr + i, w_ch.wdata[i*8 +: 8]); // [i*8+7:i*8]
                    end
                    waddr_n = waddr + (DATA_WIDTH/8);
                    if (wlen==4'd0) begin
                        wstate_n = S_W_RESP;
                    end
                    else begin
                        wlen_n = wlen - 4'd1;
                    end
                end
            end
            S_W_RESP: begin
                b_ch.bvalid = 1'b1;
                if (b_ch.bready) begin
                    wstate_n = S_W_IDLE;
                end
            end
        endcase
    end
    
    //----------------------------------------------------------
    // read channel (AR, R)
    //----------------------------------------------------------
    localparam logic [1:0] S_R_IDLE = 0,
                                S_R_ARREADY = 1,
                                S_R_DELAY = 2,
                                S_R_BURST = 3;
    
    logic [1:0] rstate, rstate_n;
    logic [7:0] rcnt, rcnt_n;
    
    logic [ADDR_WIDTH-1:0] raddr, raddr_n;
    logic [ID_WIDTH-1:0] rid, rid_n;
    logic [3:0] rlen, rlen_n;
    
    always_ff @(posedge clk)
        if (!rst_n) begin
            rstate <= S_R_IDLE;
    
            rcnt <= 8'd0;
            raddr <= {ADDR_WIDTH{1'b0}};
            rid <= {ID_WIDTH{1'b0}};
            rlen <= 4'd0;
        end
        else begin
            rstate <= rstate_n;
    
            rcnt <= rcnt_n;
            raddr <= raddr_n;
            rid <= rid_n;
            rlen <= rlen_n;
        end
    
    always_comb begin
        rstate_n = rstate;
    
        rcnt_n = rcnt;
        raddr_n = raddr;
        rid_n = rid;
        rlen_n = rlen;
    
        ar_ch.arready = 1'b0;
        r_ch.rvalid = 1'b0;
        r_ch.rlast = 1'b0;
    
        case (rstate)
            S_R_IDLE: begin
                if (ar_ch.arvalid) begin
                    if (ARREADY_DELAY == 0) begin
                        raddr_n = ar_ch.araddr;
                        rid_n = ar_ch.arid;
                        rlen_n = ar_ch.arlen;
                        ar_ch.arready = 1'b1;
    
                        rcnt_n = AR2R_DELAY - 1;
                        rstate_n = S_R_DELAY;
                    end
                    else begin
                        rcnt_n = ARREADY_DELAY-1;
                        rstate_n = S_R_ARREADY;
                    end
                end
            end
            S_R_ARREADY: begin
                if (rcnt==0) begin
                    raddr_n = ar_ch.araddr;
                    rid_n = ar_ch.arid;
                    rlen_n = ar_ch.arlen;
                    ar_ch.arready = 1'b1;
    
                    rcnt_n = AR2R_DELAY - 1;
                    rstate_n = S_R_DELAY;
                end
                else begin
                    rcnt_n = rcnt - 8'd1;
                end
            end
            S_R_DELAY: begin
                if (rcnt==0) begin
                    rstate_n = S_R_BURST;
                end
                else begin
                    rcnt_n = rcnt - 8'd1;
                end
            end
            S_R_BURST: begin
                r_ch.rvalid = 1'b1;
                r_ch.rlast = (rlen==4'd0);
                for (int i=0; i<DATA_WIDTH/8; i++) begin
                    r_ch.rdata[i*8 +: 8] = read_byte(raddr + i); // [i*8+7:i*8]
                end
                if (r_ch.rready) begin
                    raddr_n = raddr + (DATA_WIDTH/8);
                    if (rlen==4'd0) begin
                        rstate_n = S_R_IDLE;
                    end
                    else begin
                        rlen_n = rlen - 4'd1;
                    end
                end
            end
        endcase
    end
    
    // output assignments
    assign b_ch.bid = wid;
    assign b_ch.bresp = 2'd0;
    assign r_ch.rid = rid;
    assign r_ch.rresp = 2'd0;
    

    endmodule <<EndOfFile:DMAC/SIM/TB/AXI_SLAVE.sv>>

    <<StartOfFile:DMAC/SIM/TB/AXI_TYPEDEF.svh>> ifndef __AXI_TYPEDEF_SVH__ define AXI_TYPEDEF_SVH

    define AXI_ADDR_WIDTH 32 define AXI_DATA_WIDTH 32 `define AXI_ID_WIDTH 4

    `endif /* AXI_TYPEDEF_SVH */ <<EndOfFile:DMAC/SIM/TB/AXI_TYPEDEF.svh>>

    Please verify if the following table is correct using the code provided below.

    +-------+-------------------------------------------------------------------------------------+------------+-----------------------------------------------------------+-----------------------------------------+ | State | Major outputs | Next State | Next state transition condition | Notes | | +---------+--------+---------------------------------------+-------------------+------+ | | | | | ARVALID | RREADY | AWVALID | WVALID | done | | | | +-------+---------+--------+---------------------------------------+-------------------+------+------------+-----------------------------------------------------------+-----------------------------------------+ | IDLE | 0 | 0 | 0 | 0 | 1 | RREQ | (DMA_CMD.start is written as 1) and (DMA_LEN.byte_len!=0) | On moving out, | | | | | | | | | | - Copy DMA_SRC to SRC_ADDR. | | | | | | | | | | - Copy DMA_DST to DST_ADDR | | | | | | | | | | - Copy DMA_LEN to the internal counter | +-------+---------+--------+---------------------------------------+-------------------+------+------------+-----------------------------------------------------------+-----------------------------------------+ | RREQ | 1 | 0 | 0 | 0 | 0 | RDATA | ARREADY=1 | On moving out, | | | | | | | | | | - Increment ARADDR by 4 | | | | | | | | | | | | | | | | | | | | ARLEN = (cnt>=64) ? 'hF : cnt[5:2]-4'h1 | +-------+---------+--------+---------------------------------------+-------------------+------+------------+-----------------------------------------------------------+-----------------------------------------+ | RDATA | 0 | 1 | 0 | 0 | 0 | WREQ | (RVALID=1) & (RLAST) | Push data to FIFO | | | | | | | +------------+-----------------------------------------------------------+-----------------------------------------+ | | | | | | | RDATA | (RVALID) & (!RLAST) | Push data to FIFO | +-------+---------+--------+---------------------------------------+-------------------+------+------------+-----------------------------------------------------------+-----------------------------------------+ | WREQ | 0 | 0 | 1 | 0 | 0 | WDATA | AWREADY=1 | On moving out, | | | | | AWLEN=(cnt>=64) ? 'hF : cnt[5:2]-4'h1 | | | | | - Increment AWADDR by 4 | | | | | | | | | | - Decrement the internal counter by 4 | +-------+---------+--------+---------------------------------------+-------------------+------+------------+-----------------------------------------------------------+-----------------------------------------+ | WDATA | 0 | 0 | 0 | 1 | 0 | RREQ | (WREADY=1) (!WLAST) & (counter!=0) | Pop data from FIFO | | | | | | WLAST=(wcnt=='d0) | | | | Decrement wcnt | | | | | | | +------------+-----------------------------------------------------------+-----------------------------------------+ | | | | | | | IDLE | (WREADY=1) (WLAST) & (counter==0) | Pop data from FIFO | +-------+---------+--------+---------------------------------------+-------------------+------+------------+-----------------------------------------------------------+-----------------------------------------+

    Direct Memory Access (DMA) Controller Design Document V1.0

    1 Overview This document specifies the design and implementation of a Direct Memory Access Controller (DMAC) as a part of System-on-a-Chip (SoC). The main purpose of this DMAC design is to integrate into SoC for exchange a large volume of data between memory and peripherals at high speed. The proposed DMAC works on ARM’s Advanced Microcontroller Bus Architecture (AMBA) specification. The DMAC provides an AMBA APB interface to configure the IP, and an AMBA AXI interface to transfer data.

    2 Architecture Specification 2.1 General Description Some applications require transferring a volume of data between memory and peripherals without any modification on data. In software, it is commonly served by executing the memcpy library function in C, C++ or other languages. In C, the function has the following interface and copies len bytes from the object pointed by src to the object pointed by dst: void* memcpy(void* dst, const void* src, size_t len). While a pure software-based implementation of memcpy transfers data using CPU instructions, DMA does not use expensive CPU cycles but uses a hardware engine (DMAC) for the transfer. This can significantly speed up data transfers and allows using CPU for other jobs. 2.2 Usage Constraints Below describe constraints in utilizing DMAC v1. -The src and dst addresses are physical addresses. -The src and dst addresses must be a multiple of 4. -The len must be a multiple of 4. -The maximum len is 0xFFFF -Source and destination ranges must not overlap. 2.3 Programming Model Software can use the following sequence to transfer data using DMAC. -1.Write the source address to DMA_SRC register -2.Write the destination address to DMA_DST register -3.Write length to DMA_LEN register -4.Write 1 to bit[0] of DMA_CMD register -5.Wait until DMA_STATUS register has bit[0] as 1.

    2.4 Register Map In order to control DMAC, software can configure the following registers. +--------+------------+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+---+---+---+---+---+---+---+---+---+-------+ | Offset | Reg Name | 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | +--------+------------+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+---+---+---+---+---+---+---+---+---+-------+ | 0x00 | DMA_VER | version | +--------+------------+---------------------------------------------------------------------------------------------------------------------------------------------------------+ | 0x04~0xFC | Reserved | +--------+------------+---------------------------------------------------------------------------------------------------------------------------------------------------------+ | 0x100 | DMA_SRC | start_addr | +--------+------------+---------------------------------------------------------------------------------------------------------------------------------------------------------+ | 0x104 | DMA_DST | start_addr | +--------+------------+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+-------------------------------------------------------------------------+ | 0x108 | DMA_LEN | | | | | | | | | | | | | | | | | byte_len | +--------+------------+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+---+---+---+---+---+---+---+---+---+-------+ | 0x10C | DMA_CMD | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | start | +--------+------------+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+---+---+---+---+---+---+---+---+---+-------+ | 0x110 | DMA_STATUS | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | done | +--------+------------+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+---+---+---+---+---+---+---+---+---+-------+

    2.4.1 DMA VERSION

    Field nameBit rangeR/WReset valueDesciption
    version[31:0]R0x0001_2024The version of this DMA controller. The upper 16 bits represent the major version. The lower 16 bits represent the released year of the version. This document describes behaviors of major version 1.

    2.4.2 DMA_SRC

    Field nameBit rangeR/WReset valueDesciption
    start_addr[31:0]R/W0x0000_0000start address of the source range.

    2.4.3 DMA_DST

    Field nameBit rangeR/WReset valueDesciption
    start_addr[31:0]R/W0x0000_0000start address of the destination range.

    2.4.4 DMA_LEN

    Field nameBit rangeR/WReset valueDesciption
    byte_len[15:0]R/W0x0000Number of bytes to be transferred from the source to the destination.

    2.4.5 DMA_CMD Field

    Field nameBit rangeR/WReset valueDesciption
    start[0]WN/AWriting 1 to this field will initiate a DMA transfer based on DMA_SRC, DMA_DST, and DMA_LEN registers. Software must not write 1 when there’s an on-going transfer. Writing 0 to this field does not affect operation

    2.4.6 DMA_STATUS

    Field nameBit rangeR/WReset valueDesciption
    done[0]R1This field is 1 when there’s no on-going DMA transfer. Software must wait this field to be 1 for a completion of a transfer. Software must not initiate a DMA transfer when this field is 0.

    3 Micro-architecture v1.1 Specification This section describes microarchitecture of a simple DMAC. It reads data from memory, buffers the data, and write the data into memory. It repeats this procedure until it completes transferring the specified number of bytes. For simplicity, it read/writes one-cycle data (4 bytes) at a time (in other words, burst-1 transfers). For simplicity, this microarchitecture does not consider write responses from the AXI interface. Later versions will support burst transfers and write responses.

    3.1 External Interface DMAC v1.1 has the following external interfaces to communicate with other hardware IPs. -AMBA APB interface for configuration -AMBA AXI interface for data transfer

    The image you’ve uploaded is a diagram showing the on-chip interconnect of a computer system. Here’s a detailed description: The diagram illustrates how the CPU core, memory, and DMAC (Direct Memory Access Controller) are connected through an on-chip interconnect. The connections also include specific interfaces like Config interface (APB) and Data interface (AXI). “CPU core” is a box on the left side connected to the central “On-chip interconnect” cloud shape with a bidirectional arrow. Below the “CPU core,” there’s another box labeled “Memory,” also connected to the “On-chip interconnect” with a bidirectional arrow. On the right side, there’s a box labeled “DMAC” connected to both “Config interface (APB)” and “Data interface (AXI)” which are in turn connected to the central “On-chip interconnect” with bidirectional arrows. The arrows indicate that data can flow in both directions between these components.

    3.2 Block Diagram DMAC v1.1 has the following blocks inside.

    The diagram is divided into three main blocks labeled “DMAC_TOP,” “DMAC_CFG,” and “DMAC_ENGINE.” “clk” and “rst” are inputs to the “DMAC_TOP” block. An arrow labeled “APB” connects the “DMAC_TOP” block to the “DMAC_CFG” block. Another arrow labeled “AXI” connects both the “DMAC_TOP” and “DMAC_CFG” blocks to the “DMAC_ENGINE” block. Inside the “DMAC_ENGINE” block, there are four internal components labeled as follows: SRC_ADDR DST_ADDR CNT DATA BUF There’s also a small circular graph with nodes labeled 0 to 3 inside this block. This diagram is likely used to illustrate the flow of data or control signals between these components in a Direct Memory Access Controller configuration. Please let me know if you need more information!

    3.3 Configuration Register (lab2) This block receives read/write requests from the APB and configures the registers describes in Section 2.4.

    3.4 Finite State Machine (lab3) DMA engine utilizes the following state machine to control operations.

    The diagram contains five blue circles representing different states: IDLE, RREQ, RDATA, WREQ, and WDATA. Arrows connect these circles indicating the flow from one state to another. Each arrow has text annotations that describe the conditions for transitioning from one state to another. For example, transitioning from IDLE to RREQ requires writing 1 to DMA_CMD & LEN!=0, and copying DMA_SRC/DST/LEN. There are also annotations on the state circles themselves, such as “done=1” on IDLE and “AWVALID=1” on WDATA.

    +-------+--------------------------------------------+------------+-----------------------------------------------------------+----------------------------------------+ | State | Major outputs | Next State | Next state transition condition | Notes | | +---------+--------+---------+--------+------+ | | | | | ARVALID | RREADY | AWVALID | WVALID | done | | | | +-------+---------+--------+---------+--------+------+------------+-----------------------------------------------------------+----------------------------------------+ | IDLE | 0 | 0 | 0 | 0 | 1 | RREQ | (DMA_CMD.start is written as 1) and (DMA_LEN.byte_len!=0) | On moving out, | | | | | | | | | | - Copy DMA_SRC to SRC_ADDR. | | | | | | | | | | - Copy DMA_DST to DST_ADDR | | | | | | | | | | - Copy DMA_LEN to the internal counter | +-------+---------+--------+---------+--------+------+------------+-----------------------------------------------------------+----------------------------------------+ | RREQ | 1 | 0 | 0 | 0 | 0 | RDATA | ARREADY=1 | On moving out, | | | | | | | | | | - Increment ARADDR by 4 | +-------+---------+--------+---------+--------+------+------------+-----------------------------------------------------------+----------------------------------------+ | RDATA | 0 | 1 | 0 | 0 | 0 | WREQ | RVALID=1 | On moving out, | | | | | | | | | | - Buffer RDATA into the data buffer | +-------+---------+--------+---------+--------+------+------------+-----------------------------------------------------------+----------------------------------------+ | WREQ | 0 | 0 | 1 | 0 | 0 | WDATA | AWREADY=1 | On moving out, | | | | | | | | | | - Increment AWADDR by 4 | | | | | | | | | | - Decrement the internal counter by 4 | +-------+---------+--------+---------+--------+------+------------+-----------------------------------------------------------+----------------------------------------+ | WDATA | 0 | 0 | 0 | 1 | 0 | RREQ | (WREADY=1) & (counter!=0) | | | | | | | | +------------+-----------------------------------------------------------+----------------------------------------+ | | | | | | | IDLE | (WREADY=1) & (counter==0) | | +-------+---------+--------+---------+--------+------+------------+-----------------------------------------------------------+----------------------------------------+

    { "signal": [ { "name": "clk", "wave": "p....|.........." }, { "name": "state", "wave": "2.3.4|..5.6.2...", "data": ["IDLE", "RREQ", "RDATA", "WREQ", "WDATA", "IDLE"] }, { "name": "write to CMD", "wave": "010..|..........", "data": ["1"] }, {}, [ "AR ch", { "name": "ARVALID(out)", "wave": "0.1.0|..........", "data": ["SRC"] }, { "name": "ARADDR(out)", "wave": "x.3.x|..........", "data": ["SRC"] }, { "name": "ARLEN(out)", "wave": "2....|..........", "data": ["0"] }, { "name": "ARREADY(in)", "wave": "0..10|.........." }, ], [ "R ch", { "name": "RREADY(out)", "wave": "0...1|..0......." }, { "name": "RVALID(in)", "wave": "0....|.10......." }, { "name": "RDATA(in)", "wave": "x....|.4x.......", "data": ["DATA"] }, ], [ "AW ch", { "name": "AWVALID(out)", "wave": "0....|..1.0....." }, { "name": "AWADDR(out)", "wave": "x....|..5.x.....", "data": ["DST"] }, { "name": "AWLEN(out)", "wave": "2....|..........", "data": ["0"] }, { "name": "AWREADY(in)", "wave": "0....|...10....." }, ], [ "W ch", { "name": "WVALID(out)", "wave": "0....|....1.0..." }, { "name": "WDATA(out)", "wave": "x....|....4.x...", "data": ["DATA"] }, { "name": "WREADY(in)", "wave": "0....|.....10..." } ] ], "head" : { "tick" : "0" }, "foot" : { "tick" : "0" } } 그림 1. DMA operation with microarchitecture v1.1

    4 Micro-architecture v1.2 Specification (lab4) A problem with microarchitecture v1.1 is that it reads/writes data one-by-one. As memory read takes some time, DMAC v1.1 will suffer from poor performance with a long memory read latency (그림 2). We will improve the microarchitecture to transfer a burst of data to minimize performance degradation.

    { "signal": [ { "name": "clk", "wave": "p....|.................." }, { "name": "state", "wave": "2.3.4|..5.6.3.4|..5.6.3.", "data": ["IDLE", "RREQ", "RDATA", "WREQ", "WDATA", "RREQ", "RDATA", "WREQ", "WDATA", "RREQ"] }, { "name": "write to CMD", "wave": "010..|.........|........", "data": ["1"] }, {}, [ "AR ch", { "name": "ARVALID(out)", "wave": "0.1.0|......1.0|......1.", "data": ["SRC"] }, { "name": "ARADDR(out)", "wave": "x.3.x|......3.x|......3.", "data": ["SRC", "SRC+4", "SRC+8"] }, { "name": "ARLEN(out)", "wave": "2....|.........|........", "data": ["0"] }, { "name": "ARREADY(in)", "wave": "0..10|.......10|.......1" }, ], [ "R ch", { "name": "RREADY(out)", "wave": "0...1|..0.....1|..0....." }, { "name": "RVALID(in)", "wave": "0....|.10......|.10....." }, { "name": "RDATA(in)", "wave": "x....|.4x......|.4x.....", "data": ["DATA", "DATA"] }, ], [ "AW ch", { "name": "AWVALID(out)", "wave": "0....|..1.0....|..1.0..." }, { "name": "AWADDR(out)", "wave": "x....|..5.x....|..5.x...", "data": ["DST", "DST+4"] }, { "name": "AWLEN(out)", "wave": "2....|.........|........", "data": ["0"] }, { "name": "AWREADY(in)", "wave": "0....|...10....|...10..." }, ], [ "W ch", { "name": "WVALID(out)", "wave": "0....|....1.0..|....1.0." }, { "name": "WDATA(out)", "wave": "x....|....4.x..|....4.x.", "data": ["DATA", "DATA"] }, { "name": "WREADY(in)", "wave": "0....|.....10..|.....10." } ] ], "head" : { "tick" : "0" }, "foot" : { "tick" : "0" } } 그림 2. DMA operation with microarchitecture 1.1. At a time, it transfers single burst of data In Microarchitecture version 2, DMAC transfers up to 16 cycles of data with a single access. This can significantly reduce execution time by transferring data in bursts (그림 3).

  6. Assistant

    The modification you're seeking involves integrating FIFO usage into the DMAC_ENGINE module of your DMA Controller. The objective is to ensure data read from the source are buffered through the FIFO before being written to the destination, employing control signals fifo_full, fifo_empty, fifo_wren, and fifo_rden for efficient data handling.

    Below are the essential modifications and additions to your provided code under DMAC_ENGINE.sv to correctly utilize the FIFO:

    1. Adjust State Machine to Incorporate FIFO Logic: Ensure data reads into FIFO when not full and reads from FIFO when not empty. Implement FIFO write-enable (fifo_wren) when in S_RDATA state if FIFO is not full and FIFO read-enable (fifo_rden) in S_WDATA state if FIFO is not empty.

    2. FIFO Control Signal Adjustments:

    • Write Enable (fifo_wren): Enabled (1) when the state machine is in S_RDATA state and rvalid_i signal is high (data is available from read channel), and FIFO is not full.

    • Read Enable (fifo_rden): Set to 1 in S_WDATA state conditionally if FIFO is not empty.

    1. State Transaction Adjustments:
    • Transition from S_RDATA to S_WREQ state should also consider fifo_full or a specific fifo_threshold (if applicable), indicating FIFO buffer has enough data to start write operations.

    • Conditionally move to S_WREQ state from S_RDATA if FIFO is sufficiently filled (e.g., based on a threshold or if the fifo_full signal is high) or after reading the last data chunk if immediate writing is necessary even with low FIFO data.

    Here's a simplified conceptual example of modifications:

    // In the DMAC_ENGINE module:
    
    always_comb begin
        // Initial handling for state variables
        fifo_wren = 0;
        fifo_rden = 0;
        
        case (state)
            S_RDATA: begin
                rready = !fifo_full; // Only ready to read if FIFO not full
                if (rvalid_i && !fifo_full) begin
                    fifo_wren = 1; // Enable writing to FIFO when valid read data is present
                    if (rlast_i || (fifo_threshold && fifo_not_full)) begin
                        state_n = S_WREQ; // Transition to write request state based on conditions
                    end
                end
            end
            
            S_WDATA: begin
                if (!fifo_empty) begin
                    fifo_rden = 1; // Enable reading from FIFO if it's not empty
                    wvalid = 1;
                    if (wready_i && fifo_rden) begin
                        // Handle write data acknowledgment and FIFO read
                    end
                    if (wlast_i || (cnt == 0 && fifo_empty)) begin
                        state_n = S_IDLE; // Decide next state based on conditions
                    end
                end
            end
            
            // Other states handling
        endcase
    end
    
    // Logic to handle fifo_rden, fifo_wren based on state and FIFO status,
    // including data buffering strategies as per FIFO availability.
    

    Please Note: The example simplifies the logic handling for FIFO operations. You need to adjust the FIFO's full and empty signal checks, fifo_wren, and fifo_rden assignments according to your design requirements, ensuring data integrity throughout the DMA operation. This includes proper initialization, state transitions, and ensuring that FIFO read/write enable signals are correctly handled within each state of your state machine.

  7. User

    Modify the code to utilize FIFO using fifo_full, fifo_empty, fifo_wren, and fifo_rden Please fix the modifiable code in the file "DMAC/RTL/DMAC_ENGINE.sv" by modifying it.

    <<StartOfFile:DMAC/RTL/DMAC_ENGINE.sv>> module DMAC_ENGINE ( input wire clk, input wire rst_n, // _n means active low

    // configuration registers
    input wire [31:0] src_addr_i,
    input wire [31:0] dst_addr_i,
    input wire [15:0] byte_len_i,
    input wire start_i,
    output wire done_o,
    
    // AMBA AXI interface (AW channel)
    output wire [3:0] awid_o,
    output wire [31:0] awaddr_o,
    output wire [3:0] awlen_o,
    output wire [2:0] awsize_o,
    output wire [1:0] awburst_o,
    output wire awvalid_o,
    input wire awready_i,
    
    // AMBA AXI interface (W channel)
    output wire [3:0] wid_o,
    output wire [31:0] wdata_o,
    output wire [3:0] wstrb_o,
    output wire wlast_o,
    output wire wvalid_o,
    input wire wready_i,
    
    // AMBA AXI interface (B channel)
    input wire [3:0] bid_i,
    input wire [1:0] bresp_i,
    input wire bvalid_i,
    output wire bready_o,
    
    // AMBA AXI interface (AR channel)
    output wire [3:0] arid_o,
    output wire [31:0] araddr_o,
    output wire [3:0] arlen_o,
    output wire [2:0] arsize_o,
    output wire [1:0] arburst_o,
    output wire arvalid_o,
    input wire arready_i,
    
    // AMBA AXI interface (R channel)
    input wire [3:0] rid_i,
    input wire [31:0] rdata_i,
    input wire [1:0] rresp_i,
    input wire rlast_i,
    input wire rvalid_i,
    output wire rready_o
    

    );

    // mnemonics for state values
    localparam S_IDLE = 3'd0,
                                S_RREQ = 3'd1,
                                S_RDATA = 3'd2,
                                S_WREQ = 3'd3,
                                S_WDATA = 3'd4;
    
    reg [2:0] state, state_n;
    
    reg [31:0] src_addr, src_addr_n;
    reg [31:0] dst_addr, dst_addr_n;
    reg [15:0] cnt, cnt_n;
    reg [3:0] wcnt, wcnt_n;
    
    reg arvalid,
                                rready,
                                awvalid,
                                wvalid,
                                wlast,
                                done;
    
    wire fifo_full,
                                fifo_empty;
    reg fifo_wren,
                                fifo_rden;
    wire [31:0] fifo_rdata;
    
    
    // it's desirable to code registers in a simple way
    always_ff @(posedge clk)
        if (!rst_n) begin
            state <= S_IDLE;
    
            src_addr <= 32'd0;
            dst_addr <= 32'd0;
            cnt <= 16'd0;
    
            wcnt <= 4'd0;
        end
        else begin
            state <= state_n;
    
            src_addr <= src_addr_n;
            dst_addr <= dst_addr_n;
            cnt <= cnt_n;
    
            wcnt <= wcnt_n;
        end
    
    
    // this block programs output values and next register values
    // based on states.
    always_comb begin
        // START:Please modify the code correctly.
        // START:Please modify the code correctly.
        // START:Please modify the code correctly.
        state_n = state;
        src_addr_n = src_addr;
        dst_addr_n = dst_addr;
        cnt_n = cnt;
        wcnt_n = wcnt;
        arvalid = 0;
        awvalid = 0;
        wvalid = 0;
        rready = 0;
        fifo_wren = 0;
        fifo_rden = 0;
        done = 0;
        
        case (state)
            S_IDLE: begin
                done = 1;
                if (start_i && byte_len_i != 0) begin
                    src_addr_n = src_addr_i;
                    dst_addr_n = dst_addr_i;
                    cnt_n = byte_len_i;
                    state_n = S_RREQ;
                end
            end
            S_RREQ: begin
                arvalid = 1;
                if (arready_i) begin
                    src_addr_n = src_addr + 4; // Increment ARADDR by 4
                    cnt_n = cnt - 4; // Decrement the internal counter by 4
                    state_n = S_RDATA;
                end
            end
            S_RDATA: begin
                rready = !fifo_full;
                if (rvalid_i && !fifo_full) begin
                    fifo_wren = 1; // Push data to FIFO
                    if (rlast_i) begin
                        state_n = S_WREQ;
                    end
                end
            end
            S_WREQ: begin
                awvalid = 1;
                if (awready_i) begin
                    dst_addr_n = dst_addr + 4; // Increment AWADDR by 4
                    state_n = S_WDATA;
                end
            end
            S_WDATA: begin
                wvalid = !fifo_empty;
                if (wready_i && wvalid) begin
                    fifo_rden = 1; // Pop data from FIFO
                    if (wcnt == 0) begin
                        wlast = 1;
                        if (cnt == 0) begin
                            state_n = S_IDLE;
                            done = 1;
                        end else begin
                            state_n = S_RREQ; // Continue with next data chunk if counter != 0
                        end
                    end
                end
            end
        endcase
        // END:Please modify the code correctly.
        // END:Please modify the code correctly.
        // END:Please modify the code correctly.
        // ********************** 
    end
    
    DMAC_FIFO u_fifo
    (
        .clk (clk),
        .rst_n (rst_n),
    
        .full_o (fifo_full),
        .wren_i (fifo_wren),
        .wdata_i (rdata_i),
    
        .empty_o (fifo_empty),
        .rden_i (fifo_rden),
        .rdata_o (fifo_rdata)
    );
    
    // Output assigments
    assign done_o = done;
    
    assign awid_o = 4'd0;
    assign awaddr_o = dst_addr;
    assign awlen_o = (cnt >= 'd64) ? 4'hF: cnt[5:2]-4'h1;
    assign awsize_o = 3'b010; // 4 bytes per transfer
    assign awburst_o = 2'b01; // incremental
    assign awvalid_o = awvalid;
    
    assign wid_o = 4'd0;
    assign wdata_o = fifo_rdata;
    assign wstrb_o = 4'b1111; // all bytes within 4 byte are valid
    assign wlast_o = wlast;
    assign wvalid_o = wvalid;
    
    assign bready_o = 1'b1;
    
    assign arvalid_o = arvalid;
    assign araddr_o = src_addr;
    assign arid_o = 4'd0;
    assign arlen_o = (cnt >= 'd64) ? 4'hF: cnt[5:2]-4'h1;
    assign arsize_o = 3'b010; // 4 bytes per transfer
    assign arburst_o = 2'b01; // incremental
    assign arvalid_o = arvalid;
    
    assign rready_o = rready & !fifo_full;
    

    endmodule <<EndOfFile:DMAC/RTL/DMAC_ENGINE.sv>>

    { "signal": [ { "name": "clk", "wave": "p....|....|.......|....." }, { "name": "state", "wave": "2.3.4|....|..5.6..|..3.4", "data": ["IDLE", "RREQ", "RDATA", "WREQ", "WDATA", "RREQ"] }, { "name": "write to CMD", "wave": "010..|....|.......|.....", "data": ["1"] }, {}, [ "AR ch", { "name": "ARVALID(out)", "wave": "0.1.0|....|.......|.....", "data": ["SRC"] }, { "name": "ARADDR(out)", "wave": "x.3.x|....|.......|.....", "data": ["SRC"] }, { "name": "ARLEN(out)", "wave": "2....|....|.......|.....", "data": ["15"] }, { "name": "ARREADY(in)", "wave": "0..10|....|.......|....." }, ], [ "R ch", { "name": "RREADY(out)", "wave": "0...1|....|..0....|....." }, { "name": "RVALID(in)", "wave": "0....|.1..|..0....|....." }, { "name": "RLAST(in)", "wave": "0....|....|.10....|....." }, { "name": "RDATA(in)", "wave": "x....|.444|44x....|.....", "data": ["D0", "D1", "D2", "D14", "D15"] }, ], [ "AW ch", { "name": "AWVALID(out)", "wave": "0....|....|..1.0..|....." }, { "name": "AWADDR(out)", "wave": "x....|....|..5.x..|.....", "data": ["DST"] }, { "name": "AWLEN(out)", "wave": "2....|....|.......|.....", "data": ["15"] }, { "name": "AWREADY(in)", "wave": "0....|....|...10..|....." }, ], [ "W ch", { "name": "WVALID(out)", "wave": "0....|....|....1..|..0.." }, { "name": "WDATA(out)", "wave": "x....|....|....444|44x..", "data": ["D0", "D1", "D2", "D14", "D15"] }, { "name": "WLAST(out)", "wave": "0....|....|.......|.10.." }, { "name": "WREADY(in)", "wave": "0....|....|....1..|..0.." } ] ], "head" : { "tick" : "0" }, "foot" : { "tick" : "0" } } 그림 3. DMA operation with burst transfers. At a time, a request reads/writes 16 cycles of data.

    Please verify if the following table is correct using the code provided below.

    +-------+-------------------------------------------------------------------------------------+------------+-----------------------------------------------------------+-----------------------------------------+ | State | Major outputs | Next State | Next state transition condition | Notes | | +---------+--------+---------------------------------------+-------------------+------+ | | | | | ARVALID | RREADY | AWVALID | WVALID | done | | | | +-------+---------+--------+---------------------------------------+-------------------+------+------------+-----------------------------------------------------------+-----------------------------------------+ | IDLE | 0 | 0 | 0 | 0 | 1 | RREQ | (DMA_CMD.start is written as 1) and (DMA_LEN.byte_len!=0) | On moving out, | | | | | | | | | | - Copy DMA_SRC to SRC_ADDR. | | | | | | | | | | - Copy DMA_DST to DST_ADDR | | | | | | | | | | - Copy DMA_LEN to the internal counter | +-------+---------+--------+---------------------------------------+-------------------+------+------------+-----------------------------------------------------------+-----------------------------------------+ | RREQ | 1 | 0 | 0 | 0 | 0 | RDATA | ARREADY=1 | On moving out, | | | | | | | | | | - Increment ARADDR by 4 | | | | | | | | | | | | | | | | | | | | ARLEN = (cnt>=64) ? 'hF : cnt[5:2]-4'h1 | +-------+---------+--------+---------------------------------------+-------------------+------+------------+-----------------------------------------------------------+-----------------------------------------+ | RDATA | 0 | 1 | 0 | 0 | 0 | WREQ | (RVALID=1) & (RLAST) | Push data to FIFO | | | | | | | +------------+-----------------------------------------------------------+-----------------------------------------+ | | | | | | | RDATA | (RVALID) & (!RLAST) | Push data to FIFO | +-------+---------+--------+---------------------------------------+-------------------+------+------------+-----------------------------------------------------------+-----------------------------------------+ | WREQ | 0 | 0 | 1 | 0 | 0 | WDATA | AWREADY=1 | On moving out, | | | | | AWLEN=(cnt>=64) ? 'hF : cnt[5:2]-4'h1 | | | | | - Increment AWADDR by 4 | | | | | | | | | | - Decrement the internal counter by 4 | +-------+---------+--------+---------------------------------------+-------------------+------+------------+-----------------------------------------------------------+-----------------------------------------+ | WDATA | 0 | 0 | 0 | 1 | 0 | RREQ | (WREADY=1) (!WLAST) & (counter!=0) | Pop data from FIFO | | | | | | WLAST=(wcnt=='d0) | | | | Decrement wcnt | | | | | | | +------------+-----------------------------------------------------------+-----------------------------------------+ | | | | | | | IDLE | (WREADY=1) (WLAST) & (counter==0) | Pop data from FIFO | +-------+---------+--------+---------------------------------------+-------------------+------+------------+-----------------------------------------------------------+-----------------------------------------+

    <<StartOfFile:DMAC/RTL/DMAC_FIFO.sv>> module DMAC_FIFO #( parameter DEPTH_LG2 = 4, parameter DATA_WIDTH = 32 ) ( input wire clk, input wire rst_n,

    output wire full_o,
    input wire wren_i,
    input wire [DATA_WIDTH-1:0] wdata_i,
    
    output wire empty_o,
    input wire rden_i,
    output wire [DATA_WIDTH-1:0] rdata_o
    

    );

    localparam FIFO_DEPTH = (1<<DEPTH_LG2);
    
    reg [DATA_WIDTH-1:0] data[FIFO_DEPTH];
    
    reg full, full_n,
                                        empty, empty_n;
    reg [DEPTH_LG2:0] wrptr, wrptr_n,
                                        rdptr, rdptr_n;
    
    // reset entries to all 0s
    always_ff @(posedge clk)
        if (!rst_n) begin
            full <= 1'b0;
            empty <= 1'b1; // empty after as reset
    
            wrptr <= {(DEPTH_LG2+1){1'b0}};
            rdptr <= {(DEPTH_LG2+1){1'b0}};
    
            for (int i=0; i<FIFO_DEPTH; i++) begin
                data[i] <= {DATA_WIDTH{1'b0}};
            end
        end
        else begin
            full <= full_n;
            empty <= empty_n;
    
            wrptr <= wrptr_n;
            rdptr <= rdptr_n;
    
            if (wren_i) begin
                data[wrptr[DEPTH_LG2-1:0]] <= wdata_i;
            end
        end
    
    always_comb begin
        wrptr_n = wrptr;
        rdptr_n = rdptr;
    
        if (wren_i) begin
            wrptr_n = wrptr + 'd1;
        end
    
        if (rden_i) begin
            rdptr_n = rdptr + 'd1;
        end
    
        empty_n = (wrptr_n == rdptr_n);
        full_n = (wrptr_n[DEPTH_LG2]!=rdptr_n[DEPTH_LG2])
                                     &(wrptr_n[DEPTH_LG2-1:0]==rdptr_n[DEPTH_LG2-1:0]);
    
    end
    
    // synthesis translate_off
    always @(posedge clk) begin
        if (full_o & wren_i) begin
            \$display("FIFO overflow");
            @(posedge clk);
            \$finish;
        end
    end
    
    always @(posedge clk) begin
        if (empty_o & rden_i) begin
            \$display("FIFO underflow");
            @(posedge clk);
            \$finish;
        end
    end
    // synthesis translate_on
    
    assign full_o = full;
    assign empty_o = empty;
    assign rdata_o = data[rdptr[DEPTH_LG2-1:0]];
    

    endmodule <<EndOfFile:DMAC/RTL/DMAC_FIFO.sv>>

    <<StartOfFile:DMAC/SIM/TB/DMAC_TOP_TB.sv>> define IP_VER 32'h000 define SRC_ADDR 32'h100 define DST_ADDR 32'h104 define LEN_ADDR 32'h108 define STAT_ADDR 32'h110 define START_ADDR 32'h10c

    `define TIMEOUT_CYCLE 999999 module DMAC_TOP_TB ();

    reg clk;
    reg rst_n;
    
    // clock generation
    initial begin
        clk = 1'b0;
    
        forever #10 clk = !clk;
    end
    
    // reset generation
    initial begin
        rst_n = 1'b0; // active at time 0
    
        repeat (3) @(posedge clk); // after 3 cycles,
        rst_n = 1'b1; // release the reset
    end
    
    // enable waveform dump
    initial begin
        \$dumpvars(0, u_DUT);
        \$dumpfile("dump.vcd");
    end
    

    // timeout initial begin #`TIMEOUT_CYCLE $display("Timeout!"); $finish; end

    APB apb_if (.clk(clk));
    
    AXI_AW_CH aw_ch (.clk(clk));
    AXI_W_CH w_ch (.clk(clk));
    AXI_B_CH b_ch (.clk(clk));
    AXI_AR_CH ar_ch (.clk(clk));
    AXI_R_CH r_ch (.clk(clk));
    
    task test_init();
        int data;
        apb_if.init();
    
        @(posedge rst_n); // wait for a release of the reset
        repeat (10) @(posedge clk); // wait another 10 cycles
    
        apb_if.read(`IP_VER, data);
        \$display("---------------------------------------------------");
        \$display("IP version: %x", data);
        \$display("---------------------------------------------------");
    
        \$display("---------------------------------------------------");
        \$display("Reset value test");
        \$display("---------------------------------------------------");
        apb_if.read(`SRC_ADDR, data);
        if (data===0)
            \$display("DMA_SRC(pass): %x", data);
        else begin
            \$display("DMA_SRC(fail): %x", data);
            @(posedge clk);
            \$finish;
        end
        apb_if.read(`DST_ADDR, data);
        if (data===0)
            \$display("DMA_DST(pass): %x", data);
        else begin
            \$display("DMA_DST(fail): %x", data);
            @(posedge clk);
            \$finish;
        end
        apb_if.read(`LEN_ADDR, data);
        if (data===0)
            \$display("DMA_LEN(pass): %x", data);
        else begin
            \$display("DMA_LEN(fail): %x", data);
            @(posedge clk);
            \$finish;
        end
        apb_if.read(`STAT_ADDR, data);
        if (data===1)
            \$display("DMA_STATUS(pass): %x", data);
        else begin
            \$display("DMA_STATUS(fail): %x", data);
            @(posedge clk);
            \$finish;
        end
    endtask
    
    task test_dma(input int src, input int dst, input int len);
        int data;
        int word;
        realtime elapsed_time;
    
        \$display("---------------------------------------------------");
        \$display("Load data to memory");
        \$display("---------------------------------------------------");
        for (int i=src; i<(src+len); i=i+4) begin
            word = \$random; 
            u_mem.write_word(i, word);
        end
    
        \$display("---------------------------------------------------");
        \$display("Configuration test");
        \$display("---------------------------------------------------");
        apb_if.write(`SRC_ADDR, src);
        apb_if.read(`SRC_ADDR, data);
        if (data===src)
            \$display("DMA_SRC(pass): %x", data);
        else begin
            \$display("DMA_SRC(fail): %x", data);
            @(posedge clk);
            \$finish;
        end
        apb_if.write(`DST_ADDR, dst);
        apb_if.read(`DST_ADDR, data);
        if (data===dst)
            \$display("DMA_DST(pass): %x", data);
        else begin
            \$display("DMA_DST(fail): %x", data);
            @(posedge clk);
            \$finish;
        end
        apb_if.write(`LEN_ADDR, len);
        apb_if.read(`LEN_ADDR, data);
        if (data===len)
            \$display("DMA_LEN(pass): %x", data);
        else begin
            \$display("DMA_LEN(fail): %x", data);
            @(posedge clk);
            \$finish;
        end
    
        \$display("---------------------------------------------------");
        \$display("DMA start");
        \$display("---------------------------------------------------");
        apb_if.write(`START_ADDR, 32'h1);
        elapsed_time = \$realtime;
    
        \$display("---------------------------------------------------");
        \$display("Wait for a DMA completion");
        \$display("---------------------------------------------------");
        data = 0;
        while (data!=1) begin
            apb_if.read(`STAT_ADDR, data);
            repeat (100) @(posedge clk);
        end
        @(posedge clk);
        elapsed_time = \$realtime - elapsed_time;
        \$timeformat(-9, 0, " ns", 10);
        \$display("Elapsed time for DMA: %t", elapsed_time);
    
        \$display("---------------------------------------------------");
        \$display("DMA completed");
        \$display("---------------------------------------------------");
    
        repeat (len) @(posedge clk); // to make sure data is written
    
        \$display("---------------------------------------------------");
        \$display("verify data");
        \$display("---------------------------------------------------");
        for (int i=0; i<len; i=i+4) begin
            logic [31:0] src_word;
            logic [31:0] dst_word;
            src_word = u_mem.read_word(src+i);
            dst_word = u_mem.read_word(dst+i);
            if (src_word!==dst_word) begin
                \$display("Mismatch! (src:%x @%x, dst:%x @%x", src_word, src+i, dst_word, dst+i);
            end
        end
    endtask
    
    int src,
                    dst,
                    len;
    
    // main
    initial begin
        test_init();
    
        src = 'h0000_1000;
        dst = 'h0000_2000;
        len = 'h0100;
        \$display("===================================================");
        \$display("= 1st trial"); 
        \$display("= Copying %x bytes from %x to %x", len, src, dst);
        \$display("===================================================");
        test_dma(src, dst, len);
    
        src = 'h1234_1234;
        dst = 'hABCD_ABCC;
        len = 'h0F00;
        \$display("===================================================");
        \$display("= 2nd trial (long transfer)");
        \$display("= Copying %x bytes from %x to %x", len, src, dst);
        \$display("===================================================");
        test_dma(src, dst, len);
    
        src = 'h4278_0000;
        dst = 'h4278_1000;
        len = 'h0F10;
        \$display("===================================================");
        \$display("= 3rd trial (long transfer-2)");
        \$display("= Copying %x bytes from %x to %x", len, src, dst);
        \$display("===================================================");
        test_dma(src, dst, len);
        \$finish;
    end
    
    
    AXI_SLAVE u_mem (
        .clk (clk),
        .rst_n (rst_n),
    
        .aw_ch (aw_ch),
        .w_ch (w_ch),
        .b_ch (b_ch),
        .ar_ch (ar_ch),
        .r_ch (r_ch)
    );
    
    DMAC_TOP u_DUT (
        .clk (clk),
        .rst_n (rst_n),
    
        // APB interface
        .psel_i (apb_if.psel),
        .penable_i (apb_if.penable),
        .paddr_i (apb_if.paddr[11:0]),
        .pwrite_i (apb_if.pwrite),
        .pwdata_i (apb_if.pwdata),
        .pready_o (apb_if.pready),
        .prdata_o (apb_if.prdata),
        .pslverr_o (apb_if.pslverr),
    
        // AXI AW channel
        .awid_o (aw_ch.awid),
        .awaddr_o (aw_ch.awaddr),
        .awlen_o (aw_ch.awlen),
        .awsize_o (aw_ch.awsize),
        .awburst_o (aw_ch.awburst),
        .awvalid_o (aw_ch.awvalid),
        .awready_i (aw_ch.awready),
    
        // AXI W channel
        .wid_o (w_ch.wid),
        .wdata_o (w_ch.wdata),
        .wstrb_o (w_ch.wstrb),
        .wlast_o (w_ch.wlast),
        .wvalid_o (w_ch.wvalid),
        .wready_i (w_ch.wready),
    
        // AXI B channel
        .bid_i (b_ch.bid),
        .bresp_i (b_ch.bresp),
        .bvalid_i (b_ch.bvalid),
        .bready_o (b_ch.bready),
    
        // AXI AR channel
        .arid_o (ar_ch.arid),
        .araddr_o (ar_ch.araddr),
        .arlen_o (ar_ch.arlen),
        .arsize_o (ar_ch.arsize),
        .arburst_o (ar_ch.arburst),
        .arvalid_o (ar_ch.arvalid),
        .arready_i (ar_ch.arready),
    
        // AXI R channel
        .rid_i (r_ch.rid),
        .rdata_i (r_ch.rdata),
        .rresp_i (r_ch.rresp),
        .rlast_i (r_ch.rlast),
        .rvalid_i (r_ch.rvalid),
        .rready_o (r_ch.rready)
    );
    

    endmodule <<EndOfFile:DMAC/SIM/TB/DMAC_TOP_TB.sv>>

    <StartOfFile:DMAC/RTL/DMAC_CFG.sv>> module DMAC_CFG ( input wire clk, input wire rst_n, // _n means active low

    // AMBA APB interface
    input wire psel_i,
    input wire penable_i,
    input wire [11:0] paddr_i,
    input wire pwrite_i,
    input wire [31:0] pwdata_i,
    output reg pready_o,
    output reg [31:0] prdata_o,
    output reg pslverr_o,
    
    // configuration registers
    output reg [31:0] src_addr_o,
    output reg [31:0] dst_addr_o,
    output reg [15:0] byte_len_o,
    output wire start_o,
    input wire done_i
    

    );

    // Configuration register to read/write
    reg [31:0] src_addr;
    reg [31:0] dst_addr;
    reg [15:0] byte_len;
    
    //----------------------------------------------------------
    // Write
    //----------------------------------------------------------
    // an APB write occurs when PSEL & PENABLE & PWRITE
    // clk : __--__--__--__--__--__--__--__--__--__--
    // psel : ___--------_____________________________
    // penable : _______----_____________________________
    // pwrite : ___--------_____________________________
    // wren : _______----_____________________________
    //
    // DMA start command must be asserted when APB writes 1 to the DMA_CMD
    // register
    // clk : __--__--__--__--__--__--__--__--__--__--
    // psel : ___--------_____________________________
    // penable : _______----_____________________________
    // pwrite : ___--------_____________________________
    // paddr : |DMA_CMD|
    // pwdata : | 1 |
    // start : _______----_____________________________
    
    wire wren = psel_i & penable_i & pwrite_i;
    
    always @(posedge clk) begin
        if (!rst_n) begin
            src_addr <= 32'd0;
            dst_addr <= 32'd0;
            byte_len <= 16'd0;
        end
        else if (wren) begin
            case (paddr_i)
                'h100: src_addr <= pwdata_i[31:0];
                'h104: dst_addr <= pwdata_i[31:0];
                'h108: byte_len <= pwdata_i[15:0];
            endcase
        end
    end
    wire start = wren & (paddr_i=='h10C) & pwdata_i[0];
    
    //----------------------------------------------------------
    // READ
    //----------------------------------------------------------
    // an APB read occurs when PSEL & PENABLE & !PWRITE
    // To make read data a direct output from register,
    // this code shall buffer the muxed read data into a register
    // in the SETUP cycle (PSEL & !PENABLE)
    // clk : __--__--__--__--__--__--__--__--__--__--
    // psel : ___--------_____________________________
    // penable : _______----_____________________________
    // pwrite : ________________________________________
    // reg update : ___----_________________________________
    // prdata : |DATA
    
    reg [31:0] rdata;
    
    always @(posedge clk) begin
        if (!rst_n) begin
            rdata <= 32'd0;
        end
        else if (psel_i & !penable_i & !pwrite_i) begin // in the setup cycle in the APB state diagram
            case (paddr_i)
                'h0: rdata <= 32'h0001_2024;
                'h100: rdata <= src_addr;
                'h104: rdata <= dst_addr;
                'h108: rdata <= {16'd0, byte_len};
                'h110: rdata <= {31'd0, done_i};
                default: rdata <= 32'd0;
            endcase
        end
    end
    
    // output assignments
    assign pready_o = 1'b1;
    assign prdata_o = rdata;
    assign pslverr_o = 1'b0;
    
    assign src_addr_o = src_addr;
    assign dst_addr_o = dst_addr;
    assign byte_len_o = byte_len;
    assign start_o = start;
    

    endmodule <<EndOfFile:DMAC/RTL/DMAC_CFG.sv>>

    <<StartOfFile:DMAC/RTL/DMAC_TOP.sv>> module DMAC_TOP ( input wire clk, input wire rst_n, // _n means active low

    // AMBA APB interface
    input wire psel_i,
    input wire penable_i,
    input wire [11:0] paddr_i,
    input wire pwrite_i,
    input wire [31:0] pwdata_i,
    output reg pready_o,
    output reg [31:0] prdata_o,
    output reg pslverr_o,
    
    // AMBA AXI interface (AW channel)
    output wire [3:0] awid_o,
    output wire [31:0] awaddr_o,
    output wire [3:0] awlen_o,
    output wire [2:0] awsize_o,
    output wire [1:0] awburst_o,
    output wire awvalid_o,
    input wire awready_i,
    
    // AMBA AXI interface (AW channel)
    output wire [3:0] wid_o,
    output wire [31:0] wdata_o,
    output wire [3:0] wstrb_o,
    output wire wlast_o,
    output wire wvalid_o,
    input wire wready_i,
    
    // AMBA AXI interface (B channel)
    input wire [3:0] bid_i,
    input wire [1:0] bresp_i,
    input wire bvalid_i,
    output wire bready_o,
    
    // AMBA AXI interface (AR channel)
    output wire [3:0] arid_o,
    output wire [31:0] araddr_o,
    output wire [3:0] arlen_o,
    output wire [2:0] arsize_o,
    output wire [1:0] arburst_o,
    output wire arvalid_o,
    input wire arready_i,
    
    // AMBA AXI interface (R channel)
    input wire [3:0] rid_i,
    input wire [31:0] rdata_i,
    input wire [1:0] rresp_i,
    input wire rlast_i,
    input wire rvalid_i,
    output wire rready_o
    

    );

    wire [31:0] src_addr;
    wire [31:0] dst_addr;
    wire [15:0] byte_len;
    wire start;
    wire done;
    
    DMAC_CFG u_cfg(
        .clk (clk),
        .rst_n (rst_n),
    
        // AMBA APB interface
        .psel_i (psel_i),
        .penable_i (penable_i),
        .paddr_i (paddr_i),
        .pwrite_i (pwrite_i),
        .pwdata_i (pwdata_i),
        .pready_o (pready_o),
        .prdata_o (prdata_o),
        .pslverr_o (pslverr_o),
    
        .src_addr_o (src_addr),
        .dst_addr_o (dst_addr),
        .byte_len_o (byte_len),
        .start_o (start),
        .done_i (done)
    );
    
    DMAC_ENGINE u_engine(
        .clk (clk),
        .rst_n (rst_n),
    
        // configuration registers
        .src_addr_i (src_addr),
        .dst_addr_i (dst_addr),
        .byte_len_i (byte_len),
        .start_i (start),
        .done_o (done),
    
        // AMBA AXI interface (AW channel)
        .awid_o (awid_o),
        .awaddr_o (awaddr_o),
        .awlen_o (awlen_o),
        .awsize_o (awsize_o),
        .awburst_o (awburst_o),
        .awvalid_o (awvalid_o),
        .awready_i (awready_i),
    
        // AMBA AXI interface (W channel)
        .wid_o (wid_o),
        .wdata_o (wdata_o),
        .wstrb_o (wstrb_o),
        .wlast_o (wlast_o),
        .wvalid_o (wvalid_o),
        .wready_i (wready_i),
    
        // AMBA AXI interface (B channel)
        .bid_i (bid_i),
        .bresp_i (bresp_i),
        .bvalid_i (bvalid_i),
        .bready_o (bready_o),
    
        // AMBA AXI interface (AR channel)
        .arid_o (arid_o),
        .araddr_o (araddr_o),
        .arlen_o (arlen_o),
        .arsize_o (arsize_o),
        .arburst_o (arburst_o),
        .arvalid_o (arvalid_o),
        .arready_i (arready_i),
    
        // AMBA AXI interface (R channel)
        .rid_i (rid_i),
        .rdata_i (rdata_i),
        .rresp_i (rresp_i),
        .rlast_i (rlast_i),
        .rvalid_i (rvalid_i),
        .rready_o (rready_o)
    );
    

    endmodule <<EndOfFile:DMAC/RTL/DMAC_TOP.sv>>

    <<StartOfFile:DMAC/SIM/TB/AXI_INTF.sv>> `include "../TB/AXI_TYPEDEF.svh"

    interface AXI_AW_CH #( parameter ADDR_WIDTH = AXI_ADDR_WIDTH, parameter ID_WIDTH = AXI_ID_WIDTH ) ( input clk ); logic awvalid; logic awready; logic [ID_WIDTH-1:0] awid; logic [ADDR_WIDTH-1:0] awaddr; logic [3:0] awlen; logic [2:0] awsize; logic [1:0] awburst;

    endinterface

    interface AXI_W_CH #( parameter DATA_WIDTH = AXI_DATA_WIDTH, parameter ID_WIDTH = AXI_ID_WIDTH ) ( input clk ); logic wvalid; logic wready; logic [ID_WIDTH-1:0] wid; logic [DATA_WIDTH-1:0] wdata; logic [DATA_WIDTH/8-1:0] wstrb; logic wlast;

    endinterface

    interface AXI_B_CH #( parameter ID_WIDTH = `AXI_ID_WIDTH ) ( input clk ); logic bvalid; logic bready; logic [ID_WIDTH-1:0] bid; logic [1:0] bresp;

    endinterface

    interface AXI_AR_CH #( parameter ADDR_WIDTH = AXI_ADDR_WIDTH, parameter ID_WIDTH = AXI_ID_WIDTH ) ( input clk ); logic arvalid; logic arready; logic [ID_WIDTH-1:0] arid; logic [ADDR_WIDTH-1:0] araddr; logic [3:0] arlen; logic [2:0] arsize; logic [1:0] arburst;

    endinterface

    interface AXI_R_CH #( parameter DATA_WIDTH = AXI_DATA_WIDTH, parameter ID_WIDTH = AXI_ID_WIDTH ) ( input clk ); logic rvalid; logic rready; logic [ID_WIDTH-1:0] rid; logic [DATA_WIDTH-1:0] rdata; logic [1:0] rresp; logic rlast;

    endinterface

    interface APB ( input clk ); logic psel; logic penable; logic [31:0] paddr; logic pwrite; logic [31:0] pwdata; logic pready; logic [31:0] prdata; logic pslverr;

    modport master (
        input clk,
        input pready, prdata, pslverr,
        output psel, penable, paddr, pwrite, pwdata
    );
    
    task init();
        psel = 1'b0;
        penable = 1'b0;
        paddr = 32'd0;
        pwrite = 1'b0;
        pwdata = 32'd0;
    endtask
    
    task write(input int addr,
               input int data);
        #1
        psel = 1'b1;
        penable = 1'b0;
        paddr = addr;
        pwrite = 1'b1;
        pwdata = data;
        @(posedge clk);
        #1
        penable = 1'b1;
        @(posedge clk);
    
        while (pready==1'b0) begin
            @(posedge clk);
        end
    
        psel = 1'b0;
        penable = 1'b0;
        paddr = 'hX;
        pwrite = 1'bx;
        pwdata = 'hX;
    endtask
    
    task read(input int addr,
              output int data);
        #1
        psel = 1'b1;
        penable = 1'b0;
        paddr = addr;
        pwrite = 1'b0;
        pwdata = 'hX;
        @(posedge clk);
        #1
        penable = 1'b1;
        @(posedge clk);
    
        while (pready==1'b0) begin
            @(posedge clk);
        end
        data = prdata;
    
        psel = 1'b0;
        penable = 1'b0;
        paddr = 'hX;
        pwrite = 1'bx;
        pwdata = 'hX;
    endtask
    

    endinterface <<EndOfFile:DMAC/SIM/TB/AXI_INTF.sv>>

    <<StartOfFile:DMAC/SIM/TB/AXI_SLAVE.sv>> `include "../TB/AXI_TYPEDEF.svh"

    module AXI_SLAVE #( parameter ADDR_WIDTH = 16, parameter DATA_WIDTH = AXI_DATA_WIDTH, parameter ID_WIDTH = AXI_ID_WIDTH, parameter AWREADY_DELAY = 1, parameter ARREADY_DELAY = 1, parameter AR2R_DELAY = 50 ) ( input wire clk, input wire rst_n, // _n means active low

    AXI_AW_CH aw_ch,
    AXI_W_CH w_ch,
    AXI_B_CH b_ch,
    AXI_AR_CH ar_ch,
    AXI_R_CH r_ch
    

    );

    localparam DATA_DEPTH = 1<<ADDR_WIDTH;
    
    logic [7:0] mem[DATA_DEPTH];
    
    function void write_byte(int addr, input bit [7:0] wdata);
        mem[addr] = wdata;
    endfunction
    
    function void write_word(int addr, input bit [31:0] wdata);
        for (int i=0; i<4; i++) begin
            write_byte(addr+i, wdata[8*i +: 8]); // [i*8+7:i*8]
        end
    endfunction
    
    function bit [7:0] read_byte(int addr);
        read_byte = mem[addr];
    endfunction
    
    function bit [31:0] read_word(int addr);
        for (int i=0; i<4; i++) begin
            read_word[8*i +: 8] = read_byte(addr+i);// [i*8+7:i*8]
        end
    endfunction
    
    //----------------------------------------------------------
    // write channels (AW, W, B)
    //----------------------------------------------------------
    localparam logic [1:0] S_W_IDLE = 0,
                                S_W_AWREADY = 1,
                                S_W_BURST = 2,
                                S_W_RESP = 3;
    
    logic [1:0] wstate, wstate_n;
    logic [7:0] wcnt, wcnt_n;
    
    logic [ADDR_WIDTH-1:0] waddr, waddr_n;
    logic [ID_WIDTH-1:0] wid, wid_n;
    logic [3:0] wlen, wlen_n;
    
    always_ff @(posedge clk)
        if (!rst_n) begin
            wstate <= S_W_IDLE;
    
            wcnt <= 8'd0;
            waddr <= {ADDR_WIDTH{1'b0}};
            wid <= {ID_WIDTH{1'b0}};
            wlen <= 4'd0;
        end
        else begin
            wstate <= wstate_n;
    
            wcnt <= wcnt_n;
            waddr <= waddr_n;
            wid <= wid_n;
            wlen <= wlen_n;
        end
    
    always @(*) begin
        wstate_n = wstate;
    
        wcnt_n = wcnt;
        waddr_n = waddr;
        wid_n = wid;
        wlen_n = wlen;
    
        aw_ch.awready = 1'b0;
        w_ch.wready = 1'b0;
        b_ch.bvalid = 1'b0;
    
        case (wstate)
            S_W_IDLE: begin
                if (aw_ch.awvalid) begin
                    if (AWREADY_DELAY == 0) begin
                        waddr_n = aw_ch.awaddr;
                        wid_n = aw_ch.awid;
                        wlen_n = aw_ch.awlen;
                        aw_ch.awready = 1'b1;
                        wstate_n = S_W_BURST;
                    end
                    else begin
                        wcnt_n = AWREADY_DELAY-1;
                        wstate_n = S_W_AWREADY;
                    end
                end
            end
            S_W_AWREADY: begin
                if (wcnt==0) begin
                    waddr_n = aw_ch.awaddr;
                    wid_n = aw_ch.awid;
                    wlen_n = aw_ch.awlen;
                    aw_ch.awready = 1'b1;
                    wstate_n = S_W_BURST;
                end
                else begin
                    wcnt_n = wcnt - 8'd1;
                end
            end
            S_W_BURST: begin
                w_ch.wready = 1'b1;
                if (w_ch.wvalid) begin
                    for (int i=0; i<DATA_WIDTH/8; i++) begin
                        write_byte(waddr + i, w_ch.wdata[i*8 +: 8]); // [i*8+7:i*8]
                    end
                    waddr_n = waddr + (DATA_WIDTH/8);
                    if (wlen==4'd0) begin
                        wstate_n = S_W_RESP;
                    end
                    else begin
                        wlen_n = wlen - 4'd1;
                    end
                end
            end
            S_W_RESP: begin
                b_ch.bvalid = 1'b1;
                if (b_ch.bready) begin
                    wstate_n = S_W_IDLE;
                end
            end
        endcase
    end
    
    //----------------------------------------------------------
    // read channel (AR, R)
    //----------------------------------------------------------
    localparam logic [1:0] S_R_IDLE = 0,
                                S_R_ARREADY = 1,
                                S_R_DELAY = 2,
                                S_R_BURST = 3;
    
    logic [1:0] rstate, rstate_n;
    logic [7:0] rcnt, rcnt_n;
    
    logic [ADDR_WIDTH-1:0] raddr, raddr_n;
    logic [ID_WIDTH-1:0] rid, rid_n;
    logic [3:0] rlen, rlen_n;
    
    always_ff @(posedge clk)
        if (!rst_n) begin
            rstate <= S_R_IDLE;
    
            rcnt <= 8'd0;
            raddr <= {ADDR_WIDTH{1'b0}};
            rid <= {ID_WIDTH{1'b0}};
            rlen <= 4'd0;
        end
        else begin
            rstate <= rstate_n;
    
            rcnt <= rcnt_n;
            raddr <= raddr_n;
            rid <= rid_n;
            rlen <= rlen_n;
        end
    
    always_comb begin
        rstate_n = rstate;
    
        rcnt_n = rcnt;
        raddr_n = raddr;
        rid_n = rid;
        rlen_n = rlen;
    
        ar_ch.arready = 1'b0;
        r_ch.rvalid = 1'b0;
        r_ch.rlast = 1'b0;
    
        case (rstate)
            S_R_IDLE: begin
                if (ar_ch.arvalid) begin
                    if (ARREADY_DELAY == 0) begin
                        raddr_n = ar_ch.araddr;
                        rid_n = ar_ch.arid;
                        rlen_n = ar_ch.arlen;
                        ar_ch.arready = 1'b1;
    
                        rcnt_n = AR2R_DELAY - 1;
                        rstate_n = S_R_DELAY;
                    end
                    else begin
                        rcnt_n = ARREADY_DELAY-1;
                        rstate_n = S_R_ARREADY;
                    end
                end
            end
            S_R_ARREADY: begin
                if (rcnt==0) begin
                    raddr_n = ar_ch.araddr;
                    rid_n = ar_ch.arid;
                    rlen_n = ar_ch.arlen;
                    ar_ch.arready = 1'b1;
    
                    rcnt_n = AR2R_DELAY - 1;
                    rstate_n = S_R_DELAY;
                end
                else begin
                    rcnt_n = rcnt - 8'd1;
                end
            end
            S_R_DELAY: begin
                if (rcnt==0) begin
                    rstate_n = S_R_BURST;
                end
                else begin
                    rcnt_n = rcnt - 8'd1;
                end
            end
            S_R_BURST: begin
                r_ch.rvalid = 1'b1;
                r_ch.rlast = (rlen==4'd0);
                for (int i=0; i<DATA_WIDTH/8; i++) begin
                    r_ch.rdata[i*8 +: 8] = read_byte(raddr + i); // [i*8+7:i*8]
                end
                if (r_ch.rready) begin
                    raddr_n = raddr + (DATA_WIDTH/8);
                    if (rlen==4'd0) begin
                        rstate_n = S_R_IDLE;
                    end
                    else begin
                        rlen_n = rlen - 4'd1;
                    end
                end
            end
        endcase
    end
    
    // output assignments
    assign b_ch.bid = wid;
    assign b_ch.bresp = 2'd0;
    assign r_ch.rid = rid;
    assign r_ch.rresp = 2'd0;
    

    endmodule <<EndOfFile:DMAC/SIM/TB/AXI_SLAVE.sv>>

    <<StartOfFile:DMAC/SIM/TB/AXI_TYPEDEF.svh>> ifndef __AXI_TYPEDEF_SVH__ define AXI_TYPEDEF_SVH

    define AXI_ADDR_WIDTH 32 define AXI_DATA_WIDTH 32 `define AXI_ID_WIDTH 4

    `endif /* AXI_TYPEDEF_SVH */ <<EndOfFile:DMAC/SIM/TB/AXI_TYPEDEF.svh>>

    Please verify if the following table is correct using the code provided below.

    +-------+-------------------------------------------------------------------------------------+------------+-----------------------------------------------------------+-----------------------------------------+ | State | Major outputs | Next State | Next state transition condition | Notes | | +---------+--------+---------------------------------------+-------------------+------+ | | | | | ARVALID | RREADY | AWVALID | WVALID | done | | | | +-------+---------+--------+---------------------------------------+-------------------+------+------------+-----------------------------------------------------------+-----------------------------------------+ | IDLE | 0 | 0 | 0 | 0 | 1 | RREQ | (DMA_CMD.start is written as 1) and (DMA_LEN.byte_len!=0) | On moving out, | | | | | | | | | | - Copy DMA_SRC to SRC_ADDR. | | | | | | | | | | - Copy DMA_DST to DST_ADDR | | | | | | | | | | - Copy DMA_LEN to the internal counter | +-------+---------+--------+---------------------------------------+-------------------+------+------------+-----------------------------------------------------------+-----------------------------------------+ | RREQ | 1 | 0 | 0 | 0 | 0 | RDATA | ARREADY=1 | On moving out, | | | | | | | | | | - Increment ARADDR by 4 | | | | | | | | | | | | | | | | | | | | ARLEN = (cnt>=64) ? 'hF : cnt[5:2]-4'h1 | +-------+---------+--------+---------------------------------------+-------------------+------+------------+-----------------------------------------------------------+-----------------------------------------+ | RDATA | 0 | 1 | 0 | 0 | 0 | WREQ | (RVALID=1) & (RLAST) | Push data to FIFO | | | | | | | +------------+-----------------------------------------------------------+-----------------------------------------+ | | | | | | | RDATA | (RVALID) & (!RLAST) | Push data to FIFO | +-------+---------+--------+---------------------------------------+-------------------+------+------------+-----------------------------------------------------------+-----------------------------------------+ | WREQ | 0 | 0 | 1 | 0 | 0 | WDATA | AWREADY=1 | On moving out, | | | | | AWLEN=(cnt>=64) ? 'hF : cnt[5:2]-4'h1 | | | | | - Increment AWADDR by 4 | | | | | | | | | | - Decrement the internal counter by 4 | +-------+---------+--------+---------------------------------------+-------------------+------+------------+-----------------------------------------------------------+-----------------------------------------+ | WDATA | 0 | 0 | 0 | 1 | 0 | RREQ | (WREADY=1) (!WLAST) & (counter!=0) | Pop data from FIFO | | | | | | WLAST=(wcnt=='d0) | | | | Decrement wcnt | | | | | | | +------------+-----------------------------------------------------------+-----------------------------------------+ | | | | | | | IDLE | (WREADY=1) (WLAST) & (counter==0) | Pop data from FIFO | +-------+---------+--------+---------------------------------------+-------------------+------+------------+-----------------------------------------------------------+-----------------------------------------+

    Direct Memory Access (DMA) Controller Design Document V1.0

    1 Overview This document specifies the design and implementation of a Direct Memory Access Controller (DMAC) as a part of System-on-a-Chip (SoC). The main purpose of this DMAC design is to integrate into SoC for exchange a large volume of data between memory and peripherals at high speed. The proposed DMAC works on ARM’s Advanced Microcontroller Bus Architecture (AMBA) specification. The DMAC provides an AMBA APB interface to configure the IP, and an AMBA AXI interface to transfer data.

    2 Architecture Specification 2.1 General Description Some applications require transferring a volume of data between memory and peripherals without any modification on data. In software, it is commonly served by executing the memcpy library function in C, C++ or other languages. In C, the function has the following interface and copies len bytes from the object pointed by src to the object pointed by dst: void* memcpy(void* dst, const void* src, size_t len). While a pure software-based implementation of memcpy transfers data using CPU instructions, DMA does not use expensive CPU cycles but uses a hardware engine (DMAC) for the transfer. This can significantly speed up data transfers and allows using CPU for other jobs. 2.2 Usage Constraints Below describe constraints in utilizing DMAC v1. -The src and dst addresses are physical addresses. -The src and dst addresses must be a multiple of 4. -The len must be a multiple of 4. -The maximum len is 0xFFFF -Source and destination ranges must not overlap. 2.3 Programming Model Software can use the following sequence to transfer data using DMAC. -1.Write the source address to DMA_SRC register -2.Write the destination address to DMA_DST register -3.Write length to DMA_LEN register -4.Write 1 to bit[0] of DMA_CMD register -5.Wait until DMA_STATUS register has bit[0] as 1.

    2.4 Register Map In order to control DMAC, software can configure the following registers. +--------+------------+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+---+---+---+---+---+---+---+---+---+-------+ | Offset | Reg Name | 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | +--------+------------+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+---+---+---+---+---+---+---+---+---+-------+ | 0x00 | DMA_VER | version | +--------+------------+---------------------------------------------------------------------------------------------------------------------------------------------------------+ | 0x04~0xFC | Reserved | +--------+------------+---------------------------------------------------------------------------------------------------------------------------------------------------------+ | 0x100 | DMA_SRC | start_addr | +--------+------------+---------------------------------------------------------------------------------------------------------------------------------------------------------+ | 0x104 | DMA_DST | start_addr | +--------+------------+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+-------------------------------------------------------------------------+ | 0x108 | DMA_LEN | | | | | | | | | | | | | | | | | byte_len | +--------+------------+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+---+---+---+---+---+---+---+---+---+-------+ | 0x10C | DMA_CMD | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | start | +--------+------------+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+---+---+---+---+---+---+---+---+---+-------+ | 0x110 | DMA_STATUS | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | done | +--------+------------+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+---+---+---+---+---+---+---+---+---+-------+

    2.4.1 DMA VERSION

    Field nameBit rangeR/WReset valueDesciption
    version[31:0]R0x0001_2024The version of this DMA controller. The upper 16 bits represent the major version. The lower 16 bits represent the released year of the version. This document describes behaviors of major version 1.

    2.4.2 DMA_SRC

    Field nameBit rangeR/WReset valueDesciption
    start_addr[31:0]R/W0x0000_0000start address of the source range.

    2.4.3 DMA_DST

    Field nameBit rangeR/WReset valueDesciption
    start_addr[31:0]R/W0x0000_0000start address of the destination range.

    2.4.4 DMA_LEN

    Field nameBit rangeR/WReset valueDesciption
    byte_len[15:0]R/W0x0000Number of bytes to be transferred from the source to the destination.

    2.4.5 DMA_CMD Field

    Field nameBit rangeR/WReset valueDesciption
    start[0]WN/AWriting 1 to this field will initiate a DMA transfer based on DMA_SRC, DMA_DST, and DMA_LEN registers. Software must not write 1 when there’s an on-going transfer. Writing 0 to this field does not affect operation

    2.4.6 DMA_STATUS

    Field nameBit rangeR/WReset valueDesciption
    done[0]R1This field is 1 when there’s no on-going DMA transfer. Software must wait this field to be 1 for a completion of a transfer. Software must not initiate a DMA transfer when this field is 0.

    3 Micro-architecture v1.1 Specification This section describes microarchitecture of a simple DMAC. It reads data from memory, buffers the data, and write the data into memory. It repeats this procedure until it completes transferring the specified number of bytes. For simplicity, it read/writes one-cycle data (4 bytes) at a time (in other words, burst-1 transfers). For simplicity, this microarchitecture does not consider write responses from the AXI interface. Later versions will support burst transfers and write responses.

    3.1 External Interface DMAC v1.1 has the following external interfaces to communicate with other hardware IPs. -AMBA APB interface for configuration -AMBA AXI interface for data transfer

    The image you’ve uploaded is a diagram showing the on-chip interconnect of a computer system. Here’s a detailed description: The diagram illustrates how the CPU core, memory, and DMAC (Direct Memory Access Controller) are connected through an on-chip interconnect. The connections also include specific interfaces like Config interface (APB) and Data interface (AXI). “CPU core” is a box on the left side connected to the central “On-chip interconnect” cloud shape with a bidirectional arrow. Below the “CPU core,” there’s another box labeled “Memory,” also connected to the “On-chip interconnect” with a bidirectional arrow. On the right side, there’s a box labeled “DMAC” connected to both “Config interface (APB)” and “Data interface (AXI)” which are in turn connected to the central “On-chip interconnect” with bidirectional arrows. The arrows indicate that data can flow in both directions between these components.

    3.2 Block Diagram DMAC v1.1 has the following blocks inside.

    The diagram is divided into three main blocks labeled “DMAC_TOP,” “DMAC_CFG,” and “DMAC_ENGINE.” “clk” and “rst” are inputs to the “DMAC_TOP” block. An arrow labeled “APB” connects the “DMAC_TOP” block to the “DMAC_CFG” block. Another arrow labeled “AXI” connects both the “DMAC_TOP” and “DMAC_CFG” blocks to the “DMAC_ENGINE” block. Inside the “DMAC_ENGINE” block, there are four internal components labeled as follows: SRC_ADDR DST_ADDR CNT DATA BUF There’s also a small circular graph with nodes labeled 0 to 3 inside this block. This diagram is likely used to illustrate the flow of data or control signals between these components in a Direct Memory Access Controller configuration. Please let me know if you need more information!

    3.3 Configuration Register (lab2) This block receives read/write requests from the APB and configures the registers describes in Section 2.4.

    3.4 Finite State Machine (lab3) DMA engine utilizes the following state machine to control operations.

    The diagram contains five blue circles representing different states: IDLE, RREQ, RDATA, WREQ, and WDATA. Arrows connect these circles indicating the flow from one state to another. Each arrow has text annotations that describe the conditions for transitioning from one state to another. For example, transitioning from IDLE to RREQ requires writing 1 to DMA_CMD & LEN!=0, and copying DMA_SRC/DST/LEN. There are also annotations on the state circles themselves, such as “done=1” on IDLE and “AWVALID=1” on WDATA.

    +-------+--------------------------------------------+------------+-----------------------------------------------------------+----------------------------------------+ | State | Major outputs | Next State | Next state transition condition | Notes | | +---------+--------+---------+--------+------+ | | | | | ARVALID | RREADY | AWVALID | WVALID | done | | | | +-------+---------+--------+---------+--------+------+------------+-----------------------------------------------------------+----------------------------------------+ | IDLE | 0 | 0 | 0 | 0 | 1 | RREQ | (DMA_CMD.start is written as 1) and (DMA_LEN.byte_len!=0) | On moving out, | | | | | | | | | | - Copy DMA_SRC to SRC_ADDR. | | | | | | | | | | - Copy DMA_DST to DST_ADDR | | | | | | | | | | - Copy DMA_LEN to the internal counter | +-------+---------+--------+---------+--------+------+------------+-----------------------------------------------------------+----------------------------------------+ | RREQ | 1 | 0 | 0 | 0 | 0 | RDATA | ARREADY=1 | On moving out, | | | | | | | | | | - Increment ARADDR by 4 | +-------+---------+--------+---------+--------+------+------------+-----------------------------------------------------------+----------------------------------------+ | RDATA | 0 | 1 | 0 | 0 | 0 | WREQ | RVALID=1 | On moving out, | | | | | | | | | | - Buffer RDATA into the data buffer | +-------+---------+--------+---------+--------+------+------------+-----------------------------------------------------------+----------------------------------------+ | WREQ | 0 | 0 | 1 | 0 | 0 | WDATA | AWREADY=1 | On moving out, | | | | | | | | | | - Increment AWADDR by 4 | | | | | | | | | | - Decrement the internal counter by 4 | +-------+---------+--------+---------+--------+------+------------+-----------------------------------------------------------+----------------------------------------+ | WDATA | 0 | 0 | 0 | 1 | 0 | RREQ | (WREADY=1) & (counter!=0) | | | | | | | | +------------+-----------------------------------------------------------+----------------------------------------+ | | | | | | | IDLE | (WREADY=1) & (counter==0) | | +-------+---------+--------+---------+--------+------+------------+-----------------------------------------------------------+----------------------------------------+

    { "signal": [ { "name": "clk", "wave": "p....|.........." }, { "name": "state", "wave": "2.3.4|..5.6.2...", "data": ["IDLE", "RREQ", "RDATA", "WREQ", "WDATA", "IDLE"] }, { "name": "write to CMD", "wave": "010..|..........", "data": ["1"] }, {}, [ "AR ch", { "name": "ARVALID(out)", "wave": "0.1.0|..........", "data": ["SRC"] }, { "name": "ARADDR(out)", "wave": "x.3.x|..........", "data": ["SRC"] }, { "name": "ARLEN(out)", "wave": "2....|..........", "data": ["0"] }, { "name": "ARREADY(in)", "wave": "0..10|.........." }, ], [ "R ch", { "name": "RREADY(out)", "wave": "0...1|..0......." }, { "name": "RVALID(in)", "wave": "0....|.10......." }, { "name": "RDATA(in)", "wave": "x....|.4x.......", "data": ["DATA"] }, ], [ "AW ch", { "name": "AWVALID(out)", "wave": "0....|..1.0....." }, { "name": "AWADDR(out)", "wave": "x....|..5.x.....", "data": ["DST"] }, { "name": "AWLEN(out)", "wave": "2....|..........", "data": ["0"] }, { "name": "AWREADY(in)", "wave": "0....|...10....." }, ], [ "W ch", { "name": "WVALID(out)", "wave": "0....|....1.0..." }, { "name": "WDATA(out)", "wave": "x....|....4.x...", "data": ["DATA"] }, { "name": "WREADY(in)", "wave": "0....|.....10..." } ] ], "head" : { "tick" : "0" }, "foot" : { "tick" : "0" } } 그림 1. DMA operation with microarchitecture v1.1

    4 Micro-architecture v1.2 Specification (lab4) A problem with microarchitecture v1.1 is that it reads/writes data one-by-one. As memory read takes some time, DMAC v1.1 will suffer from poor performance with a long memory read latency (그림 2). We will improve the microarchitecture to transfer a burst of data to minimize performance degradation.

    { "signal": [ { "name": "clk", "wave": "p....|.................." }, { "name": "state", "wave": "2.3.4|..5.6.3.4|..5.6.3.", "data": ["IDLE", "RREQ", "RDATA", "WREQ", "WDATA", "RREQ", "RDATA", "WREQ", "WDATA", "RREQ"] }, { "name": "write to CMD", "wave": "010..|.........|........", "data": ["1"] }, {}, [ "AR ch", { "name": "ARVALID(out)", "wave": "0.1.0|......1.0|......1.", "data": ["SRC"] }, { "name": "ARADDR(out)", "wave": "x.3.x|......3.x|......3.", "data": ["SRC", "SRC+4", "SRC+8"] }, { "name": "ARLEN(out)", "wave": "2....|.........|........", "data": ["0"] }, { "name": "ARREADY(in)", "wave": "0..10|.......10|.......1" }, ], [ "R ch", { "name": "RREADY(out)", "wave": "0...1|..0.....1|..0....." }, { "name": "RVALID(in)", "wave": "0....|.10......|.10....." }, { "name": "RDATA(in)", "wave": "x....|.4x......|.4x.....", "data": ["DATA", "DATA"] }, ], [ "AW ch", { "name": "AWVALID(out)", "wave": "0....|..1.0....|..1.0..." }, { "name": "AWADDR(out)", "wave": "x....|..5.x....|..5.x...", "data": ["DST", "DST+4"] }, { "name": "AWLEN(out)", "wave": "2....|.........|........", "data": ["0"] }, { "name": "AWREADY(in)", "wave": "0....|...10....|...10..." }, ], [ "W ch", { "name": "WVALID(out)", "wave": "0....|....1.0..|....1.0." }, { "name": "WDATA(out)", "wave": "x....|....4.x..|....4.x.", "data": ["DATA", "DATA"] }, { "name": "WREADY(in)", "wave": "0....|.....10..|.....10." } ] ], "head" : { "tick" : "0" }, "foot" : { "tick" : "0" } } 그림 2. DMA operation with microarchitecture 1.1. At a time, it transfers single burst of data In Microarchitecture version 2, DMAC transfers up to 16 cycles of data with a single access. This can significantly reduce execution time by transferring data in bursts (그림 3).

  8. Assistant

    The modifications to your DMAC_ENGINE.sv file, specified around integrating FIFO control with fifo_full, fifo_empty, fifo_wren, and fifo_rden, can be incorporated as follows. The crucial steps involve checking FIFO status before data operations to manage data flow efficiently.

    Suggestions for Modifications:

    1. During Reading Data into FIFO (S_RDATA State):

      • Only attempt to read data from the AXI read channel when the FIFO is not full.
      • Signal fifo_wren should be asserted when valid data is being read (rvalid_i is high) and the FIFO is not full.
    2. Before Writing Data from FIFO to Destination (S_WDATA State):

      • Writing data out to the destination should only be attempted when the FIFO is not empty.
      • Signal fifo_rden should be asserted when ready to write (wready_i is high) and the FIFO is not empty.

    Here's an adapted snippet focusing on crucial FIFO integration parts (Note: Simplified for brevity):

    always_comb begin
        // Defaults
        fifo_wren = 0;
        fifo_rden = 0;
        arvalid = 0;
        awvalid = 0;
        wvalid = 0;
        rready = 0;
        
        case (state)
            S_IDLE: begin
                done = start_i ? 0 : 1;
                if (start_i && byte_len_i != 0) begin
                    // Initialization for transfer
                    state_n = S_RREQ;
                    // Further initialization logic...
                end
            end
            S_RREQ: begin
                if (!fifo_full) begin
                    arvalid = 1; // Request to read when FIFO not full
                    // Transition to RDATA upon readiness...
                end
            end
            S_RDATA: begin
                rready = !fifo_full; // Only ready to receive data if FIFO not full
                if (rvalid_i && !fifo_full) begin
                    fifo_wren = 1; // Enable writing to FIFO
                    // Handle transition to next state...
                end
            end
            S_WREQ: begin
                if (!fifo_empty) begin
                    awvalid = 1; // Ready to request write operation
                    // Transition to WDATA upon readiness...
                end
            end
            S_WDATA: begin
                if (!fifo_empty && wready_i) begin
                    fifo_rden = 1; // Pop data from FIFO
                    wvalid = 1; // Indicating valid write data
                    // Finalize transfer or loop back for more reads...
                end
            end
            // Additional state logic...
        endcase
    end
    

    Key Integration Aspects:

    • FIFO Read and Write Enable Signals: Managed according to FIFO status and data channel readiness (rvalid_i, wready_i).
    • Handling Full FIFO during Reads and Empty FIFO during Writes: Prevents data loss and underflow, respectively.

    Remember, this adaptation simplifies handling and doesn't cover all aspects, like initializing counters or handling the last data chunk (wlast). You'll need to integrate it within your existing logic, ensuring alignment with your state machine's current design and ensuring correct transitions between states based on FIFO status and data availability/requirements.

  9. User

    "데이터가 미스매치가 발생하는데 원인을 알 수 있는가?"를 영어로 출력해주세요.

  10. Assistant

    "Is it possible to identify the cause of the data mismatch?"

  11. User

    Is it possible to identify the cause of the data mismatch?

    <<StartOfFile:DMAC/RTL/DMAC_ENGINE.sv>> module DMAC_ENGINE ( input wire clk, input wire rst_n, // _n means active low

    // configuration registers
    input wire [31:0] src_addr_i,
    input wire [31:0] dst_addr_i,
    input wire [15:0] byte_len_i,
    input wire start_i,
    output wire done_o,
    
    // AMBA AXI interface (AW channel)
    output wire [3:0] awid_o,
    output wire [31:0] awaddr_o,
    output wire [3:0] awlen_o,
    output wire [2:0] awsize_o,
    output wire [1:0] awburst_o,
    output wire awvalid_o,
    input wire awready_i,
    
    // AMBA AXI interface (W channel)
    output wire [3:0] wid_o,
    output wire [31:0] wdata_o,
    output wire [3:0] wstrb_o,
    output wire wlast_o,
    output wire wvalid_o,
    input wire wready_i,
    
    // AMBA AXI interface (B channel)
    input wire [3:0] bid_i,
    input wire [1:0] bresp_i,
    input wire bvalid_i,
    output wire bready_o,
    
    // AMBA AXI interface (AR channel)
    output wire [3:0] arid_o,
    output wire [31:0] araddr_o,
    output wire [3:0] arlen_o,
    output wire [2:0] arsize_o,
    output wire [1:0] arburst_o,
    output wire arvalid_o,
    input wire arready_i,
    
    // AMBA AXI interface (R channel)
    input wire [3:0] rid_i,
    input wire [31:0] rdata_i,
    input wire [1:0] rresp_i,
    input wire rlast_i,
    input wire rvalid_i,
    output wire rready_o
    

    );

    // mnemonics for state values
    localparam S_IDLE = 3'd0,
                                S_RREQ = 3'd1,
                                S_RDATA = 3'd2,
                                S_WREQ = 3'd3,
                                S_WDATA = 3'd4;
    
    reg [2:0] state, state_n;
    
    reg [31:0] src_addr, src_addr_n;
    reg [31:0] dst_addr, dst_addr_n;
    reg [15:0] cnt, cnt_n;
    reg [3:0] wcnt, wcnt_n;
    
    reg arvalid,
                                rready,
                                awvalid,
                                wvalid,
                                wlast,
                                done;
    
    wire fifo_full,
                                fifo_empty;
    reg fifo_wren,
                                fifo_rden;
    wire [31:0] fifo_rdata;
    
    
    // it's desirable to code registers in a simple way
    always_ff @(posedge clk)
        if (!rst_n) begin
            state <= S_IDLE;
    
            src_addr <= 32'd0;
            dst_addr <= 32'd0;
            cnt <= 16'd0;
    
            wcnt <= 4'd0;
        end
        else begin
            state <= state_n;
    
            src_addr <= src_addr_n;
            dst_addr <= dst_addr_n;
            cnt <= cnt_n;
    
            wcnt <= wcnt_n;
        end
    
    
    // this block programs output values and next register values
    // based on states.
    always_comb begin
        // START:Please modify the code correctly.
        // START:Please modify the code correctly.
        // START:Please modify the code correctly.
        // Defaults
        fifo_wren = 0;
        fifo_rden = 0;
        arvalid = 0;
        awvalid = 0;
        wvalid = 0;
        rready = 0;
        
        case (state)
            S_IDLE: begin
                done = start_i ? 0 : 1;
                if (start_i && byte_len_i != 0) begin
                    // Initialization for transfer
                    state_n = S_RREQ;
                    // Further initialization logic…
                end
            end
            S_RREQ: begin
                if (!fifo_full) begin
                    arvalid = 1; // Request to read when FIFO not full
                    // Transition to RDATA upon readiness…
                end
            end
            S_RDATA: begin
                rready = !fifo_full; // Only ready to receive data if FIFO not full
                if (rvalid_i && !fifo_full) begin
                    fifo_wren = 1; // Enable writing to FIFO
                    // Handle transition to next state…
                end
            end
            S_WREQ: begin
                if (!fifo_empty) begin
                    awvalid = 1; // Ready to request write operation
                    // Transition to WDATA upon readiness…
                end
            end
            S_WDATA: begin
                if (!fifo_empty && wready_i) begin
                    fifo_rden = 1; // Pop data from FIFO
                    wvalid = 1; // Indicating valid write data
                    // Finalize transfer or loop back for more reads…
                end
            end
            // Additional state logic…
        endcase
        // END:Please modify the code correctly.
        // END:Please modify the code correctly.
        // END:Please modify the code correctly.
        // ********************** 
    end
    
    DMAC_FIFO u_fifo
    (
        .clk (clk),
        .rst_n (rst_n),
    
        .full_o (fifo_full),
        .wren_i (fifo_wren),
        .wdata_i (rdata_i),
    
        .empty_o (fifo_empty),
        .rden_i (fifo_rden),
        .rdata_o (fifo_rdata)
    );
    
    // Output assigments
    assign done_o = done;
    
    assign awid_o = 4'd0;
    assign awaddr_o = dst_addr;
    assign awlen_o = (cnt >= 'd64) ? 4'hF: cnt[5:2]-4'h1;
    assign awsize_o = 3'b010; // 4 bytes per transfer
    assign awburst_o = 2'b01; // incremental
    assign awvalid_o = awvalid;
    
    assign wid_o = 4'd0;
    assign wdata_o = fifo_rdata;
    assign wstrb_o = 4'b1111; // all bytes within 4 byte are valid
    assign wlast_o = wlast;
    assign wvalid_o = wvalid;
    
    assign bready_o = 1'b1;
    
    assign arvalid_o = arvalid;
    assign araddr_o = src_addr;
    assign arid_o = 4'd0;
    assign arlen_o = (cnt >= 'd64) ? 4'hF: cnt[5:2]-4'h1;
    assign arsize_o = 3'b010; // 4 bytes per transfer
    assign arburst_o = 2'b01; // incremental
    assign arvalid_o = arvalid;
    
    assign rready_o = rready & !fifo_full;
    

    endmodule <<EndOfFile:DMAC/RTL/DMAC_ENGINE.sv>>

    { "signal": [ { "name": "clk", "wave": "p....|....|.......|....." }, { "name": "state", "wave": "2.3.4|....|..5.6..|..3.4", "data": ["IDLE", "RREQ", "RDATA", "WREQ", "WDATA", "RREQ"] }, { "name": "write to CMD", "wave": "010..|....|.......|.....", "data": ["1"] }, {}, [ "AR ch", { "name": "ARVALID(out)", "wave": "0.1.0|....|.......|.....", "data": ["SRC"] }, { "name": "ARADDR(out)", "wave": "x.3.x|....|.......|.....", "data": ["SRC"] }, { "name": "ARLEN(out)", "wave": "2....|....|.......|.....", "data": ["15"] }, { "name": "ARREADY(in)", "wave": "0..10|....|.......|....." }, ], [ "R ch", { "name": "RREADY(out)", "wave": "0...1|....|..0....|....." }, { "name": "RVALID(in)", "wave": "0....|.1..|..0....|....." }, { "name": "RLAST(in)", "wave": "0....|....|.10....|....." }, { "name": "RDATA(in)", "wave": "x....|.444|44x....|.....", "data": ["D0", "D1", "D2", "D14", "D15"] }, ], [ "AW ch", { "name": "AWVALID(out)", "wave": "0....|....|..1.0..|....." }, { "name": "AWADDR(out)", "wave": "x....|....|..5.x..|.....", "data": ["DST"] }, { "name": "AWLEN(out)", "wave": "2....|....|.......|.....", "data": ["15"] }, { "name": "AWREADY(in)", "wave": "0....|....|...10..|....." }, ], [ "W ch", { "name": "WVALID(out)", "wave": "0....|....|....1..|..0.." }, { "name": "WDATA(out)", "wave": "x....|....|....444|44x..", "data": ["D0", "D1", "D2", "D14", "D15"] }, { "name": "WLAST(out)", "wave": "0....|....|.......|.10.." }, { "name": "WREADY(in)", "wave": "0....|....|....1..|..0.." } ] ], "head" : { "tick" : "0" }, "foot" : { "tick" : "0" } } 그림 3. DMA operation with burst transfers. At a time, a request reads/writes 16 cycles of data.

    Please verify if the following table is correct using the code provided below.

    +-------+-------------------------------------------------------------------------------------+------------+-----------------------------------------------------------+-----------------------------------------+ | State | Major outputs | Next State | Next state transition condition | Notes | | +---------+--------+---------------------------------------+-------------------+------+ | | | | | ARVALID | RREADY | AWVALID | WVALID | done | | | | +-------+---------+--------+---------------------------------------+-------------------+------+------------+-----------------------------------------------------------+-----------------------------------------+ | IDLE | 0 | 0 | 0 | 0 | 1 | RREQ | (DMA_CMD.start is written as 1) and (DMA_LEN.byte_len!=0) | On moving out, | | | | | | | | | | - Copy DMA_SRC to SRC_ADDR. | | | | | | | | | | - Copy DMA_DST to DST_ADDR | | | | | | | | | | - Copy DMA_LEN to the internal counter | +-------+---------+--------+---------------------------------------+-------------------+------+------------+-----------------------------------------------------------+-----------------------------------------+ | RREQ | 1 | 0 | 0 | 0 | 0 | RDATA | ARREADY=1 | On moving out, | | | | | | | | | | - Increment ARADDR by 4 | | | | | | | | | | | | | | | | | | | | ARLEN = (cnt>=64) ? 'hF : cnt[5:2]-4'h1 | +-------+---------+--------+---------------------------------------+-------------------+------+------------+-----------------------------------------------------------+-----------------------------------------+ | RDATA | 0 | 1 | 0 | 0 | 0 | WREQ | (RVALID=1) & (RLAST) | Push data to FIFO | | | | | | | +------------+-----------------------------------------------------------+-----------------------------------------+ | | | | | | | RDATA | (RVALID) & (!RLAST) | Push data to FIFO | +-------+---------+--------+---------------------------------------+-------------------+------+------------+-----------------------------------------------------------+-----------------------------------------+ | WREQ | 0 | 0 | 1 | 0 | 0 | WDATA | AWREADY=1 | On moving out, | | | | | AWLEN=(cnt>=64) ? 'hF : cnt[5:2]-4'h1 | | | | | - Increment AWADDR by 4 | | | | | | | | | | - Decrement the internal counter by 4 | +-------+---------+--------+---------------------------------------+-------------------+------+------------+-----------------------------------------------------------+-----------------------------------------+ | WDATA | 0 | 0 | 0 | 1 | 0 | RREQ | (WREADY=1) (!WLAST) & (counter!=0) | Pop data from FIFO | | | | | | WLAST=(wcnt=='d0) | | | | Decrement wcnt | | | | | | | +------------+-----------------------------------------------------------+-----------------------------------------+ | | | | | | | IDLE | (WREADY=1) (WLAST) & (counter==0) | Pop data from FIFO | +-------+---------+--------+---------------------------------------+-------------------+------+------------+-----------------------------------------------------------+-----------------------------------------+

    <<StartOfFile:DMAC/RTL/DMAC_FIFO.sv>> module DMAC_FIFO #( parameter DEPTH_LG2 = 4, parameter DATA_WIDTH = 32 ) ( input wire clk, input wire rst_n,

    output wire full_o,
    input wire wren_i,
    input wire [DATA_WIDTH-1:0] wdata_i,
    
    output wire empty_o,
    input wire rden_i,
    output wire [DATA_WIDTH-1:0] rdata_o
    

    );

    localparam FIFO_DEPTH = (1<<DEPTH_LG2);
    
    reg [DATA_WIDTH-1:0] data[FIFO_DEPTH];
    
    reg full, full_n,
                                        empty, empty_n;
    reg [DEPTH_LG2:0] wrptr, wrptr_n,
                                        rdptr, rdptr_n;
    
    // reset entries to all 0s
    always_ff @(posedge clk)
        if (!rst_n) begin
            full <= 1'b0;
            empty <= 1'b1; // empty after as reset
    
            wrptr <= {(DEPTH_LG2+1){1'b0}};
            rdptr <= {(DEPTH_LG2+1){1'b0}};
    
            for (int i=0; i<FIFO_DEPTH; i++) begin
                data[i] <= {DATA_WIDTH{1'b0}};
            end
        end
        else begin
            full <= full_n;
            empty <= empty_n;
    
            wrptr <= wrptr_n;
            rdptr <= rdptr_n;
    
            if (wren_i) begin
                data[wrptr[DEPTH_LG2-1:0]] <= wdata_i;
            end
        end
    
    always_comb begin
        wrptr_n = wrptr;
        rdptr_n = rdptr;
    
        if (wren_i) begin
            wrptr_n = wrptr + 'd1;
        end
    
        if (rden_i) begin
            rdptr_n = rdptr + 'd1;
        end
    
        empty_n = (wrptr_n == rdptr_n);
        full_n = (wrptr_n[DEPTH_LG2]!=rdptr_n[DEPTH_LG2])
                                     &(wrptr_n[DEPTH_LG2-1:0]==rdptr_n[DEPTH_LG2-1:0]);
    
    end
    
    // synthesis translate_off
    always @(posedge clk) begin
        if (full_o & wren_i) begin
            \$display("FIFO overflow");
            @(posedge clk);
            \$finish;
        end
    end
    
    always @(posedge clk) begin
        if (empty_o & rden_i) begin
            \$display("FIFO underflow");
            @(posedge clk);
            \$finish;
        end
    end
    // synthesis translate_on
    
    assign full_o = full;
    assign empty_o = empty;
    assign rdata_o = data[rdptr[DEPTH_LG2-1:0]];
    

    endmodule <<EndOfFile:DMAC/RTL/DMAC_FIFO.sv>>

    <<StartOfFile:DMAC/SIM/TB/DMAC_TOP_TB.sv>> define IP_VER 32'h000 define SRC_ADDR 32'h100 define DST_ADDR 32'h104 define LEN_ADDR 32'h108 define STAT_ADDR 32'h110 define START_ADDR 32'h10c

    `define TIMEOUT_CYCLE 999999 module DMAC_TOP_TB ();

    reg clk;
    reg rst_n;
    
    // clock generation
    initial begin
        clk = 1'b0;
    
        forever #10 clk = !clk;
    end
    
    // reset generation
    initial begin
        rst_n = 1'b0; // active at time 0
    
        repeat (3) @(posedge clk); // after 3 cycles,
        rst_n = 1'b1; // release the reset
    end
    
    // enable waveform dump
    initial begin
        \$dumpvars(0, u_DUT);
        \$dumpfile("dump.vcd");
    end
    

    // timeout initial begin #`TIMEOUT_CYCLE $display("Timeout!"); $finish; end

    APB apb_if (.clk(clk));
    
    AXI_AW_CH aw_ch (.clk(clk));
    AXI_W_CH w_ch (.clk(clk));
    AXI_B_CH b_ch (.clk(clk));
    AXI_AR_CH ar_ch (.clk(clk));
    AXI_R_CH r_ch (.clk(clk));
    
    task test_init();
        int data;
        apb_if.init();
    
        @(posedge rst_n); // wait for a release of the reset
        repeat (10) @(posedge clk); // wait another 10 cycles
    
        apb_if.read(`IP_VER, data);
        \$display("---------------------------------------------------");
        \$display("IP version: %x", data);
        \$display("---------------------------------------------------");
    
        \$display("---------------------------------------------------");
        \$display("Reset value test");
        \$display("---------------------------------------------------");
        apb_if.read(`SRC_ADDR, data);
        if (data===0)
            \$display("DMA_SRC(pass): %x", data);
        else begin
            \$display("DMA_SRC(fail): %x", data);
            @(posedge clk);
            \$finish;
        end
        apb_if.read(`DST_ADDR, data);
        if (data===0)
            \$display("DMA_DST(pass): %x", data);
        else begin
            \$display("DMA_DST(fail): %x", data);
            @(posedge clk);
            \$finish;
        end
        apb_if.read(`LEN_ADDR, data);
        if (data===0)
            \$display("DMA_LEN(pass): %x", data);
        else begin
            \$display("DMA_LEN(fail): %x", data);
            @(posedge clk);
            \$finish;
        end
        apb_if.read(`STAT_ADDR, data);
        if (data===1)
            \$display("DMA_STATUS(pass): %x", data);
        else begin
            \$display("DMA_STATUS(fail): %x", data);
            @(posedge clk);
            \$finish;
        end
    endtask
    
    task test_dma(input int src, input int dst, input int len);
        int data;
        int word;
        realtime elapsed_time;
    
        \$display("---------------------------------------------------");
        \$display("Load data to memory");
        \$display("---------------------------------------------------");
        for (int i=src; i<(src+len); i=i+4) begin
            word = \$random; 
            u_mem.write_word(i, word);
        end
    
        \$display("---------------------------------------------------");
        \$display("Configuration test");
        \$display("---------------------------------------------------");
        apb_if.write(`SRC_ADDR, src);
        apb_if.read(`SRC_ADDR, data);
        if (data===src)
            \$display("DMA_SRC(pass): %x", data);
        else begin
            \$display("DMA_SRC(fail): %x", data);
            @(posedge clk);
            \$finish;
        end
        apb_if.write(`DST_ADDR, dst);
        apb_if.read(`DST_ADDR, data);
        if (data===dst)
            \$display("DMA_DST(pass): %x", data);
        else begin
            \$display("DMA_DST(fail): %x", data);
            @(posedge clk);
            \$finish;
        end
        apb_if.write(`LEN_ADDR, len);
        apb_if.read(`LEN_ADDR, data);
        if (data===len)
            \$display("DMA_LEN(pass): %x", data);
        else begin
            \$display("DMA_LEN(fail): %x", data);
            @(posedge clk);
            \$finish;
        end
    
        \$display("---------------------------------------------------");
        \$display("DMA start");
        \$display("---------------------------------------------------");
        apb_if.write(`START_ADDR, 32'h1);
        elapsed_time = \$realtime;
    
        \$display("---------------------------------------------------");
        \$display("Wait for a DMA completion");
        \$display("---------------------------------------------------");
        data = 0;
        while (data!=1) begin
            apb_if.read(`STAT_ADDR, data);
            repeat (100) @(posedge clk);
        end
        @(posedge clk);
        elapsed_time = \$realtime - elapsed_time;
        \$timeformat(-9, 0, " ns", 10);
        \$display("Elapsed time for DMA: %t", elapsed_time);
    
        \$display("---------------------------------------------------");
        \$display("DMA completed");
        \$display("---------------------------------------------------");
    
        repeat (len) @(posedge clk); // to make sure data is written
    
        \$display("---------------------------------------------------");
        \$display("verify data");
        \$display("---------------------------------------------------");
        for (int i=0; i<len; i=i+4) begin
            logic [31:0] src_word;
            logic [31:0] dst_word;
            src_word = u_mem.read_word(src+i);
            dst_word = u_mem.read_word(dst+i);
            if (src_word!==dst_word) begin
                \$display("Mismatch! (src:%x @%x, dst:%x @%x", src_word, src+i, dst_word, dst+i);
            end
        end
    endtask
    
    int src,
                    dst,
                    len;
    
    // main
    initial begin
        test_init();
    
        src = 'h0000_1000;
        dst = 'h0000_2000;
        len = 'h0100;
        \$display("===================================================");
        \$display("= 1st trial"); 
        \$display("= Copying %x bytes from %x to %x", len, src, dst);
        \$display("===================================================");
        test_dma(src, dst, len);
    
        src = 'h1234_1234;
        dst = 'hABCD_ABCC;
        len = 'h0F00;
        \$display("===================================================");
        \$display("= 2nd trial (long transfer)");
        \$display("= Copying %x bytes from %x to %x", len, src, dst);
        \$display("===================================================");
        test_dma(src, dst, len);
    
        src = 'h4278_0000;
        dst = 'h4278_1000;
        len = 'h0F10;
        \$display("===================================================");
        \$display("= 3rd trial (long transfer-2)");
        \$display("= Copying %x bytes from %x to %x", len, src, dst);
        \$display("===================================================");
        test_dma(src, dst, len);
        \$finish;
    end
    
    
    AXI_SLAVE u_mem (
        .clk (clk),
        .rst_n (rst_n),
    
        .aw_ch (aw_ch),
        .w_ch (w_ch),
        .b_ch (b_ch),
        .ar_ch (ar_ch),
        .r_ch (r_ch)
    );
    
    DMAC_TOP u_DUT (
        .clk (clk),
        .rst_n (rst_n),
    
        // APB interface
        .psel_i (apb_if.psel),
        .penable_i (apb_if.penable),
        .paddr_i (apb_if.paddr[11:0]),
        .pwrite_i (apb_if.pwrite),
        .pwdata_i (apb_if.pwdata),
        .pready_o (apb_if.pready),
        .prdata_o (apb_if.prdata),
        .pslverr_o (apb_if.pslverr),
    
        // AXI AW channel
        .awid_o (aw_ch.awid),
        .awaddr_o (aw_ch.awaddr),
        .awlen_o (aw_ch.awlen),
        .awsize_o (aw_ch.awsize),
        .awburst_o (aw_ch.awburst),
        .awvalid_o (aw_ch.awvalid),
        .awready_i (aw_ch.awready),
    
        // AXI W channel
        .wid_o (w_ch.wid),
        .wdata_o (w_ch.wdata),
        .wstrb_o (w_ch.wstrb),
        .wlast_o (w_ch.wlast),
        .wvalid_o (w_ch.wvalid),
        .wready_i (w_ch.wready),
    
        // AXI B channel
        .bid_i (b_ch.bid),
        .bresp_i (b_ch.bresp),
        .bvalid_i (b_ch.bvalid),
        .bready_o (b_ch.bready),
    
        // AXI AR channel
        .arid_o (ar_ch.arid),
        .araddr_o (ar_ch.araddr),
        .arlen_o (ar_ch.arlen),
        .arsize_o (ar_ch.arsize),
        .arburst_o (ar_ch.arburst),
        .arvalid_o (ar_ch.arvalid),
        .arready_i (ar_ch.arready),
    
        // AXI R channel
        .rid_i (r_ch.rid),
        .rdata_i (r_ch.rdata),
        .rresp_i (r_ch.rresp),
        .rlast_i (r_ch.rlast),
        .rvalid_i (r_ch.rvalid),
        .rready_o (r_ch.rready)
    );
    

    endmodule <<EndOfFile:DMAC/SIM/TB/DMAC_TOP_TB.sv>>

    <StartOfFile:DMAC/RTL/DMAC_CFG.sv>> module DMAC_CFG ( input wire clk, input wire rst_n, // _n means active low

    // AMBA APB interface
    input wire psel_i,
    input wire penable_i,
    input wire [11:0] paddr_i,
    input wire pwrite_i,
    input wire [31:0] pwdata_i,
    output reg pready_o,
    output reg [31:0] prdata_o,
    output reg pslverr_o,
    
    // configuration registers
    output reg [31:0] src_addr_o,
    output reg [31:0] dst_addr_o,
    output reg [15:0] byte_len_o,
    output wire start_o,
    input wire done_i
    

    );

    // Configuration register to read/write
    reg [31:0] src_addr;
    reg [31:0] dst_addr;
    reg [15:0] byte_len;
    
    //----------------------------------------------------------
    // Write
    //----------------------------------------------------------
    // an APB write occurs when PSEL & PENABLE & PWRITE
    // clk : __--__--__--__--__--__--__--__--__--__--
    // psel : ___--------_____________________________
    // penable : _______----_____________________________
    // pwrite : ___--------_____________________________
    // wren : _______----_____________________________
    //
    // DMA start command must be asserted when APB writes 1 to the DMA_CMD
    // register
    // clk : __--__--__--__--__--__--__--__--__--__--
    // psel : ___--------_____________________________
    // penable : _______----_____________________________
    // pwrite : ___--------_____________________________
    // paddr : |DMA_CMD|
    // pwdata : | 1 |
    // start : _______----_____________________________
    
    wire wren = psel_i & penable_i & pwrite_i;
    
    always @(posedge clk) begin
        if (!rst_n) begin
            src_addr <= 32'd0;
            dst_addr <= 32'd0;
            byte_len <= 16'd0;
        end
        else if (wren) begin
            case (paddr_i)
                'h100: src_addr <= pwdata_i[31:0];
                'h104: dst_addr <= pwdata_i[31:0];
                'h108: byte_len <= pwdata_i[15:0];
            endcase
        end
    end
    wire start = wren & (paddr_i=='h10C) & pwdata_i[0];
    
    //----------------------------------------------------------
    // READ
    //----------------------------------------------------------
    // an APB read occurs when PSEL & PENABLE & !PWRITE
    // To make read data a direct output from register,
    // this code shall buffer the muxed read data into a register
    // in the SETUP cycle (PSEL & !PENABLE)
    // clk : __--__--__--__--__--__--__--__--__--__--
    // psel : ___--------_____________________________
    // penable : _______----_____________________________
    // pwrite : ________________________________________
    // reg update : ___----_________________________________
    // prdata : |DATA
    
    reg [31:0] rdata;
    
    always @(posedge clk) begin
        if (!rst_n) begin
            rdata <= 32'd0;
        end
        else if (psel_i & !penable_i & !pwrite_i) begin // in the setup cycle in the APB state diagram
            case (paddr_i)
                'h0: rdata <= 32'h0001_2024;
                'h100: rdata <= src_addr;
                'h104: rdata <= dst_addr;
                'h108: rdata <= {16'd0, byte_len};
                'h110: rdata <= {31'd0, done_i};
                default: rdata <= 32'd0;
            endcase
        end
    end
    
    // output assignments
    assign pready_o = 1'b1;
    assign prdata_o = rdata;
    assign pslverr_o = 1'b0;
    
    assign src_addr_o = src_addr;
    assign dst_addr_o = dst_addr;
    assign byte_len_o = byte_len;
    assign start_o = start;
    

    endmodule <<EndOfFile:DMAC/RTL/DMAC_CFG.sv>>

    <<StartOfFile:DMAC/RTL/DMAC_TOP.sv>> module DMAC_TOP ( input wire clk, input wire rst_n, // _n means active low

    // AMBA APB interface
    input wire psel_i,
    input wire penable_i,
    input wire [11:0] paddr_i,
    input wire pwrite_i,
    input wire [31:0] pwdata_i,
    output reg pready_o,
    output reg [31:0] prdata_o,
    output reg pslverr_o,
    
    // AMBA AXI interface (AW channel)
    output wire [3:0] awid_o,
    output wire [31:0] awaddr_o,
    output wire [3:0] awlen_o,
    output wire [2:0] awsize_o,
    output wire [1:0] awburst_o,
    output wire awvalid_o,
    input wire awready_i,
    
    // AMBA AXI interface (AW channel)
    output wire [3:0] wid_o,
    output wire [31:0] wdata_o,
    output wire [3:0] wstrb_o,
    output wire wlast_o,
    output wire wvalid_o,
    input wire wready_i,
    
    // AMBA AXI interface (B channel)
    input wire [3:0] bid_i,
    input wire [1:0] bresp_i,
    input wire bvalid_i,
    output wire bready_o,
    
    // AMBA AXI interface (AR channel)
    output wire [3:0] arid_o,
    output wire [31:0] araddr_o,
    output wire [3:0] arlen_o,
    output wire [2:0] arsize_o,
    output wire [1:0] arburst_o,
    output wire arvalid_o,
    input wire arready_i,
    
    // AMBA AXI interface (R channel)
    input wire [3:0] rid_i,
    input wire [31:0] rdata_i,
    input wire [1:0] rresp_i,
    input wire rlast_i,
    input wire rvalid_i,
    output wire rready_o
    

    );

    wire [31:0] src_addr;
    wire [31:0] dst_addr;
    wire [15:0] byte_len;
    wire start;
    wire done;
    
    DMAC_CFG u_cfg(
        .clk (clk),
        .rst_n (rst_n),
    
        // AMBA APB interface
        .psel_i (psel_i),
        .penable_i (penable_i),
        .paddr_i (paddr_i),
        .pwrite_i (pwrite_i),
        .pwdata_i (pwdata_i),
        .pready_o (pready_o),
        .prdata_o (prdata_o),
        .pslverr_o (pslverr_o),
    
        .src_addr_o (src_addr),
        .dst_addr_o (dst_addr),
        .byte_len_o (byte_len),
        .start_o (start),
        .done_i (done)
    );
    
    DMAC_ENGINE u_engine(
        .clk (clk),
        .rst_n (rst_n),
    
        // configuration registers
        .src_addr_i (src_addr),
        .dst_addr_i (dst_addr),
        .byte_len_i (byte_len),
        .start_i (start),
        .done_o (done),
    
        // AMBA AXI interface (AW channel)
        .awid_o (awid_o),
        .awaddr_o (awaddr_o),
        .awlen_o (awlen_o),
        .awsize_o (awsize_o),
        .awburst_o (awburst_o),
        .awvalid_o (awvalid_o),
        .awready_i (awready_i),
    
        // AMBA AXI interface (W channel)
        .wid_o (wid_o),
        .wdata_o (wdata_o),
        .wstrb_o (wstrb_o),
        .wlast_o (wlast_o),
        .wvalid_o (wvalid_o),
        .wready_i (wready_i),
    
        // AMBA AXI interface (B channel)
        .bid_i (bid_i),
        .bresp_i (bresp_i),
        .bvalid_i (bvalid_i),
        .bready_o (bready_o),
    
        // AMBA AXI interface (AR channel)
        .arid_o (arid_o),
        .araddr_o (araddr_o),
        .arlen_o (arlen_o),
        .arsize_o (arsize_o),
        .arburst_o (arburst_o),
        .arvalid_o (arvalid_o),
        .arready_i (arready_i),
    
        // AMBA AXI interface (R channel)
        .rid_i (rid_i),
        .rdata_i (rdata_i),
        .rresp_i (rresp_i),
        .rlast_i (rlast_i),
        .rvalid_i (rvalid_i),
        .rready_o (rready_o)
    );
    

    endmodule <<EndOfFile:DMAC/RTL/DMAC_TOP.sv>>

    <<StartOfFile:DMAC/SIM/TB/AXI_INTF.sv>> `include "../TB/AXI_TYPEDEF.svh"

    interface AXI_AW_CH #( parameter ADDR_WIDTH = AXI_ADDR_WIDTH, parameter ID_WIDTH = AXI_ID_WIDTH ) ( input clk ); logic awvalid; logic awready; logic [ID_WIDTH-1:0] awid; logic [ADDR_WIDTH-1:0] awaddr; logic [3:0] awlen; logic [2:0] awsize; logic [1:0] awburst;

    endinterface

    interface AXI_W_CH #( parameter DATA_WIDTH = AXI_DATA_WIDTH, parameter ID_WIDTH = AXI_ID_WIDTH ) ( input clk ); logic wvalid; logic wready; logic [ID_WIDTH-1:0] wid; logic [DATA_WIDTH-1:0] wdata; logic [DATA_WIDTH/8-1:0] wstrb; logic wlast;

    endinterface

    interface AXI_B_CH #( parameter ID_WIDTH = `AXI_ID_WIDTH ) ( input clk ); logic bvalid; logic bready; logic [ID_WIDTH-1:0] bid; logic [1:0] bresp;

    endinterface

    interface AXI_AR_CH #( parameter ADDR_WIDTH = AXI_ADDR_WIDTH, parameter ID_WIDTH = AXI_ID_WIDTH ) ( input clk ); logic arvalid; logic arready; logic [ID_WIDTH-1:0] arid; logic [ADDR_WIDTH-1:0] araddr; logic [3:0] arlen; logic [2:0] arsize; logic [1:0] arburst;

    endinterface

    interface AXI_R_CH #( parameter DATA_WIDTH = AXI_DATA_WIDTH, parameter ID_WIDTH = AXI_ID_WIDTH ) ( input clk ); logic rvalid; logic rready; logic [ID_WIDTH-1:0] rid; logic [DATA_WIDTH-1:0] rdata; logic [1:0] rresp; logic rlast;

    endinterface

    interface APB ( input clk ); logic psel; logic penable; logic [31:0] paddr; logic pwrite; logic [31:0] pwdata; logic pready; logic [31:0] prdata; logic pslverr;

    modport master (
        input clk,
        input pready, prdata, pslverr,
        output psel, penable, paddr, pwrite, pwdata
    );
    
    task init();
        psel = 1'b0;
        penable = 1'b0;
        paddr = 32'd0;
        pwrite = 1'b0;
        pwdata = 32'd0;
    endtask
    
    task write(input int addr,
               input int data);
        #1
        psel = 1'b1;
        penable = 1'b0;
        paddr = addr;
        pwrite = 1'b1;
        pwdata = data;
        @(posedge clk);
        #1
        penable = 1'b1;
        @(posedge clk);
    
        while (pready==1'b0) begin
            @(posedge clk);
        end
    
        psel = 1'b0;
        penable = 1'b0;
        paddr = 'hX;
        pwrite = 1'bx;
        pwdata = 'hX;
    endtask
    
    task read(input int addr,
              output int data);
        #1
        psel = 1'b1;
        penable = 1'b0;
        paddr = addr;
        pwrite = 1'b0;
        pwdata = 'hX;
        @(posedge clk);
        #1
        penable = 1'b1;
        @(posedge clk);
    
        while (pready==1'b0) begin
            @(posedge clk);
        end
        data = prdata;
    
        psel = 1'b0;
        penable = 1'b0;
        paddr = 'hX;
        pwrite = 1'bx;
        pwdata = 'hX;
    endtask
    

    endinterface <<EndOfFile:DMAC/SIM/TB/AXI_INTF.sv>>

    <<StartOfFile:DMAC/SIM/TB/AXI_SLAVE.sv>> `include "../TB/AXI_TYPEDEF.svh"

    module AXI_SLAVE #( parameter ADDR_WIDTH = 16, parameter DATA_WIDTH = AXI_DATA_WIDTH, parameter ID_WIDTH = AXI_ID_WIDTH, parameter AWREADY_DELAY = 1, parameter ARREADY_DELAY = 1, parameter AR2R_DELAY = 50 ) ( input wire clk, input wire rst_n, // _n means active low

    AXI_AW_CH aw_ch,
    AXI_W_CH w_ch,
    AXI_B_CH b_ch,
    AXI_AR_CH ar_ch,
    AXI_R_CH r_ch
    

    );

    localparam DATA_DEPTH = 1<<ADDR_WIDTH;
    
    logic [7:0] mem[DATA_DEPTH];
    
    function void write_byte(int addr, input bit [7:0] wdata);
        mem[addr] = wdata;
    endfunction
    
    function void write_word(int addr, input bit [31:0] wdata);
        for (int i=0; i<4; i++) begin
            write_byte(addr+i, wdata[8*i +: 8]); // [i*8+7:i*8]
        end
    endfunction
    
    function bit [7:0] read_byte(int addr);
        read_byte = mem[addr];
    endfunction
    
    function bit [31:0] read_word(int addr);
        for (int i=0; i<4; i++) begin
            read_word[8*i +: 8] = read_byte(addr+i);// [i*8+7:i*8]
        end
    endfunction
    
    //----------------------------------------------------------
    // write channels (AW, W, B)
    //----------------------------------------------------------
    localparam logic [1:0] S_W_IDLE = 0,
                                S_W_AWREADY = 1,
                                S_W_BURST = 2,
                                S_W_RESP = 3;
    
    logic [1:0] wstate, wstate_n;
    logic [7:0] wcnt, wcnt_n;
    
    logic [ADDR_WIDTH-1:0] waddr, waddr_n;
    logic [ID_WIDTH-1:0] wid, wid_n;
    logic [3:0] wlen, wlen_n;
    
    always_ff @(posedge clk)
        if (!rst_n) begin
            wstate <= S_W_IDLE;
    
            wcnt <= 8'd0;
            waddr <= {ADDR_WIDTH{1'b0}};
            wid <= {ID_WIDTH{1'b0}};
            wlen <= 4'd0;
        end
        else begin
            wstate <= wstate_n;
    
            wcnt <= wcnt_n;
            waddr <= waddr_n;
            wid <= wid_n;
            wlen <= wlen_n;
        end
    
    always @(*) begin
        wstate_n = wstate;
    
        wcnt_n = wcnt;
        waddr_n = waddr;
        wid_n = wid;
        wlen_n = wlen;
    
        aw_ch.awready = 1'b0;
        w_ch.wready = 1'b0;
        b_ch.bvalid = 1'b0;
    
        case (wstate)
            S_W_IDLE: begin
                if (aw_ch.awvalid) begin
                    if (AWREADY_DELAY == 0) begin
                        waddr_n = aw_ch.awaddr;
                        wid_n = aw_ch.awid;
                        wlen_n = aw_ch.awlen;
                        aw_ch.awready = 1'b1;
                        wstate_n = S_W_BURST;
                    end
                    else begin
                        wcnt_n = AWREADY_DELAY-1;
                        wstate_n = S_W_AWREADY;
                    end
                end
            end
            S_W_AWREADY: begin
                if (wcnt==0) begin
                    waddr_n = aw_ch.awaddr;
                    wid_n = aw_ch.awid;
                    wlen_n = aw_ch.awlen;
                    aw_ch.awready = 1'b1;
                    wstate_n = S_W_BURST;
                end
                else begin
                    wcnt_n = wcnt - 8'd1;
                end
            end
            S_W_BURST: begin
                w_ch.wready = 1'b1;
                if (w_ch.wvalid) begin
                    for (int i=0; i<DATA_WIDTH/8; i++) begin
                        write_byte(waddr + i, w_ch.wdata[i*8 +: 8]); // [i*8+7:i*8]
                    end
                    waddr_n = waddr + (DATA_WIDTH/8);
                    if (wlen==4'd0) begin
                        wstate_n = S_W_RESP;
                    end
                    else begin
                        wlen_n = wlen - 4'd1;
                    end
                end
            end
            S_W_RESP: begin
                b_ch.bvalid = 1'b1;
                if (b_ch.bready) begin
                    wstate_n = S_W_IDLE;
                end
            end
        endcase
    end
    
    //----------------------------------------------------------
    // read channel (AR, R)
    //----------------------------------------------------------
    localparam logic [1:0] S_R_IDLE = 0,
                                S_R_ARREADY = 1,
                                S_R_DELAY = 2,
                                S_R_BURST = 3;
    
    logic [1:0] rstate, rstate_n;
    logic [7:0] rcnt, rcnt_n;
    
    logic [ADDR_WIDTH-1:0] raddr, raddr_n;
    logic [ID_WIDTH-1:0] rid, rid_n;
    logic [3:0] rlen, rlen_n;
    
    always_ff @(posedge clk)
        if (!rst_n) begin
            rstate <= S_R_IDLE;
    
            rcnt <= 8'd0;
            raddr <= {ADDR_WIDTH{1'b0}};
            rid <= {ID_WIDTH{1'b0}};
            rlen <= 4'd0;
        end
        else begin
            rstate <= rstate_n;
    
            rcnt <= rcnt_n;
            raddr <= raddr_n;
            rid <= rid_n;
            rlen <= rlen_n;
        end
    
    always_comb begin
        rstate_n = rstate;
    
        rcnt_n = rcnt;
        raddr_n = raddr;
        rid_n = rid;
        rlen_n = rlen;
    
        ar_ch.arready = 1'b0;
        r_ch.rvalid = 1'b0;
        r_ch.rlast = 1'b0;
    
        case (rstate)
            S_R_IDLE: begin
                if (ar_ch.arvalid) begin
                    if (ARREADY_DELAY == 0) begin
                        raddr_n = ar_ch.araddr;
                        rid_n = ar_ch.arid;
                        rlen_n = ar_ch.arlen;
                        ar_ch.arready = 1'b1;
    
                        rcnt_n = AR2R_DELAY - 1;
                        rstate_n = S_R_DELAY;
                    end
                    else begin
                        rcnt_n = ARREADY_DELAY-1;
                        rstate_n = S_R_ARREADY;
                    end
                end
            end
            S_R_ARREADY: begin
                if (rcnt==0) begin
                    raddr_n = ar_ch.araddr;
                    rid_n = ar_ch.arid;
                    rlen_n = ar_ch.arlen;
                    ar_ch.arready = 1'b1;
    
                    rcnt_n = AR2R_DELAY - 1;
                    rstate_n = S_R_DELAY;
                end
                else begin
                    rcnt_n = rcnt - 8'd1;
                end
            end
            S_R_DELAY: begin
                if (rcnt==0) begin
                    rstate_n = S_R_BURST;
                end
                else begin
                    rcnt_n = rcnt - 8'd1;
                end
            end
            S_R_BURST: begin
                r_ch.rvalid = 1'b1;
                r_ch.rlast = (rlen==4'd0);
                for (int i=0; i<DATA_WIDTH/8; i++) begin
                    r_ch.rdata[i*8 +: 8] = read_byte(raddr + i); // [i*8+7:i*8]
                end
                if (r_ch.rready) begin
                    raddr_n = raddr + (DATA_WIDTH/8);
                    if (rlen==4'd0) begin
                        rstate_n = S_R_IDLE;
                    end
                    else begin
                        rlen_n = rlen - 4'd1;
                    end
                end
            end
        endcase
    end
    
    // output assignments
    assign b_ch.bid = wid;
    assign b_ch.bresp = 2'd0;
    assign r_ch.rid = rid;
    assign r_ch.rresp = 2'd0;
    

    endmodule <<EndOfFile:DMAC/SIM/TB/AXI_SLAVE.sv>>

    <<StartOfFile:DMAC/SIM/TB/AXI_TYPEDEF.svh>> ifndef __AXI_TYPEDEF_SVH__ define AXI_TYPEDEF_SVH

    define AXI_ADDR_WIDTH 32 define AXI_DATA_WIDTH 32 `define AXI_ID_WIDTH 4

    `endif /* AXI_TYPEDEF_SVH */ <<EndOfFile:DMAC/SIM/TB/AXI_TYPEDEF.svh>>

  12. Assistant

    Identifying the cause of a data mismatch in a DMA (Direct Memory Access) engine implementation, such as the one described here, typically involves troubleshooting and analyzing several key aspects of the design and operation. Here are several steps and considerations to help determine the cause of the mismatch:

    1. Check Configuration Parameters: Verify if the source (src_addr_i) and destination (dst_addr_i) addresses, as well as the byte length (byte_len_i), are correctly configured. Ensure these parameters match the intended data transfer details.

    2. Inspect State Transitions: Review the state machine transitions to ensure they accurately reflect the intended behavior. Make sure the transitions between IDLE, RREQ, RDATA, WREQ, and WDATA states occur under the correct conditions.

    3. FIFO Status Handling: Since the design incorporates a FIFO for buffering data, check the logic related to fifo_full and fifo_empty signals. Incorrect handling of these conditions can lead to data loss or stale data being transferred. Ensure that reads from the source pause when fifo_full is asserted and that writes to the destination wait for fifo_empty to be deasserted.

    4. AXI Interface Compliance: Verify that the AXI interface interactions comply with the AXI protocol specifications, particularly regarding handshake signals like awready, wready, arready, rvalid, and the correct setup of awlen, wlast, and other transfer control signals.

    5. Data Handling in FIFO: Ensure the logic for writing to (fifo_wren) and reading from (fifo_rden) the FIFO correctly handles data, paying close attention to potential off-by-one errors or conditions where the FIFO could be read or written erroneously.

    6. Timing and Synchronization: Look for potential timing issues or synchronization problems between the clock domains if any exist (especially concerning the clk signal).

    7. Simulation and Testing: Utilize simulation to trace and visually inspect the operation of the DMA engine, paying special attention to the data being written into and read out of the FIFO. Testbenches should be designed to cover various corner cases and boundary conditions.

    8. Hardware Debugging: If running on actual hardware, leverage integrated debugging tools, such as signal tapping, to observe real-time behavior of the DMA engine and pinpoint where data might be getting altered or lost.

    Data mismatches can stem from numerous sources, including configuration errors, logical bugs in the state machine, improper AXI interface usage, or even issues related to hardware implementation and signal integrity. A methodical approach to debugging, starting with simple test cases and gradually moving to more complex scenarios, can help isolate the problem.

  13. User

    Is it possible to identify the cause of the data mismatch?

    <<StartOfFile:DMAC/RTL/DMAC_ENGINE.sv>> module DMAC_ENGINE ( input wire clk, input wire rst_n, // _n means active low

    // configuration registers
    input wire [31:0] src_addr_i,
    input wire [31:0] dst_addr_i,
    input wire [15:0] byte_len_i,
    input wire start_i,
    output wire done_o,
    
    // AMBA AXI interface (AW channel)
    output wire [3:0] awid_o,
    output wire [31:0] awaddr_o,
    output wire [3:0] awlen_o,
    output wire [2:0] awsize_o,
    output wire [1:0] awburst_o,
    output wire awvalid_o,
    input wire awready_i,
    
    // AMBA AXI interface (W channel)
    output wire [3:0] wid_o,
    output wire [31:0] wdata_o,
    output wire [3:0] wstrb_o,
    output wire wlast_o,
    output wire wvalid_o,
    input wire wready_i,
    
    // AMBA AXI interface (B channel)
    input wire [3:0] bid_i,
    input wire [1:0] bresp_i,
    input wire bvalid_i,
    output wire bready_o,
    
    // AMBA AXI interface (AR channel)
    output wire [3:0] arid_o,
    output wire [31:0] araddr_o,
    output wire [3:0] arlen_o,
    output wire [2:0] arsize_o,
    output wire [1:0] arburst_o,
    output wire arvalid_o,
    input wire arready_i,
    
    // AMBA AXI interface (R channel)
    input wire [3:0] rid_i,
    input wire [31:0] rdata_i,
    input wire [1:0] rresp_i,
    input wire rlast_i,
    input wire rvalid_i,
    output wire rready_o
    

    );

    // mnemonics for state values
    localparam S_IDLE = 3'd0,
                                S_RREQ = 3'd1,
                                S_RDATA = 3'd2,
                                S_WREQ = 3'd3,
                                S_WDATA = 3'd4;
    
    reg [2:0] state, state_n;
    
    reg [31:0] src_addr, src_addr_n;
    reg [31:0] dst_addr, dst_addr_n;
    reg [15:0] cnt, cnt_n;
    reg [3:0] wcnt, wcnt_n;
    
    reg arvalid,
                                rready,
                                awvalid,
                                wvalid,
                                wlast,
                                done;
    
    wire fifo_full,
                                fifo_empty;
    reg fifo_wren,
                                fifo_rden;
    wire [31:0] fifo_rdata;
    
    
    // it's desirable to code registers in a simple way
    always_ff @(posedge clk)
        if (!rst_n) begin
            state <= S_IDLE;
    
            src_addr <= 32'd0;
            dst_addr <= 32'd0;
            cnt <= 16'd0;
    
            wcnt <= 4'd0;
        end
        else begin
            state <= state_n;
    
            src_addr <= src_addr_n;
            dst_addr <= dst_addr_n;
            cnt <= cnt_n;
    
            wcnt <= wcnt_n;
        end
    
    
    // this block programs output values and next register values
    // based on states.
    always_comb begin
        // START:Please modify the code correctly.
        // START:Please modify the code correctly.
        // START:Please modify the code correctly.
        fifo_wren = 0;
        fifo_rden = 0;
        arvalid = 0;
        awvalid = 0;
        wvalid = 0;
        rready = 0;
        
        case (state)
            S_IDLE: begin
                done = 1'b1;
                if (start_i && byte_len_i != 0) begin
                    state_n = S_RREQ;
                end
            end
            S_RREQ: begin
                arvalid = 1'b1;
                if (arready_i) begin
                    state_n = S_RDATA;
                    src_addr_n = src_addr + 'd4;
                    //src_addr_n = src_addr + arlen_o;
                end
            end
            S_RDATA: begin
                rready = !fifo_full;
                if (rvalid_i && !fifo_full) begin
                    fifo_wren = 1;
                    // src_addr_n = src_addr + arlen_o;
                    if (rlast_i) begin
                        state_n = S_WREQ;
                    end
                    else begin
                        state_n = S_RDATA;
                    end
                end
            end
            S_WREQ: begin
                awvalid = 1;
                if (awready_i) begin
                    state_n = S_WDATA;
                    dst_addr_n = dst_addr + 'd4;
                    cnt_n = cnt - arlen_o;
                end
                if (!fifo_empty) begin
                    dst_addr_n = dst_addr + arlen_o;
                end
            end
            S_WDATA: begin
                wvalid = 1;
                if (!fifo_empty && wready_i) begin
                    fifo_rden = 1;
                    // dst_addr_n = dst_addr + arlen_o;
                    if (wlast_o) begin
                        state_n = S_IDLE;
                    end
                    else begin
                        state_n = S_WDATA;
                    end
                end
            end
        endcase
    
        // END:Please modify the code correctly.
        // END:Please modify the code correctly.
        // END:Please modify the code correctly.
        // ********************** 
    end
    
    DMAC_FIFO u_fifo
    (
        .clk (clk),
        .rst_n (rst_n),
    
        .full_o (fifo_full),
        .wren_i (fifo_wren),
        .wdata_i (rdata_i),
    
        .empty_o (fifo_empty),
        .rden_i (fifo_rden),
        .rdata_o (fifo_rdata)
    );
    
    // Output assigments
    assign done_o = done;
    
    assign awid_o = 4'd0;
    assign awaddr_o = dst_addr;
    assign awlen_o = (cnt >= 'd64) ? 4'hF: cnt[5:2]-4'h1;
    assign awsize_o = 3'b010; // 4 bytes per transfer
    assign awburst_o = 2'b01; // incremental
    assign awvalid_o = awvalid;
    
    assign wid_o = 4'd0;
    assign wdata_o = fifo_rdata;
    assign wstrb_o = 4'b1111; // all bytes within 4 byte are valid
    assign wlast_o = wlast;
    assign wvalid_o = wvalid;
    
    assign bready_o = 1'b1;
    
    assign arvalid_o = arvalid;
    assign araddr_o = src_addr;
    assign arid_o = 4'd0;
    assign arlen_o = (cnt >= 'd64) ? 4'hF: cnt[5:2]-4'h1;
    assign arsize_o = 3'b010; // 4 bytes per transfer
    assign arburst_o = 2'b01; // incremental
    assign arvalid_o = arvalid;
    
    assign rready_o = rready & !fifo_full;
    

    endmodule <<EndOfFile:DMAC/RTL/DMAC_ENGINE.sv>>

    { "signal": [ { "name": "clk", "wave": "p....|....|.......|....." }, { "name": "state", "wave": "2.3.4|....|..5.6..|..3.4", "data": ["IDLE", "RREQ", "RDATA", "WREQ", "WDATA", "RREQ"] }, { "name": "write to CMD", "wave": "010..|....|.......|.....", "data": ["1"] }, {}, [ "AR ch", { "name": "ARVALID(out)", "wave": "0.1.0|....|.......|.....", "data": ["SRC"] }, { "name": "ARADDR(out)", "wave": "x.3.x|....|.......|.....", "data": ["SRC"] }, { "name": "ARLEN(out)", "wave": "2....|....|.......|.....", "data": ["15"] }, { "name": "ARREADY(in)", "wave": "0..10|....|.......|....." }, ], [ "R ch", { "name": "RREADY(out)", "wave": "0...1|....|..0....|....." }, { "name": "RVALID(in)", "wave": "0....|.1..|..0....|....." }, { "name": "RLAST(in)", "wave": "0....|....|.10....|....." }, { "name": "RDATA(in)", "wave": "x....|.444|44x....|.....", "data": ["D0", "D1", "D2", "D14", "D15"] }, ], [ "AW ch", { "name": "AWVALID(out)", "wave": "0....|....|..1.0..|....." }, { "name": "AWADDR(out)", "wave": "x....|....|..5.x..|.....", "data": ["DST"] }, { "name": "AWLEN(out)", "wave": "2....|....|.......|.....", "data": ["15"] }, { "name": "AWREADY(in)", "wave": "0....|....|...10..|....." }, ], [ "W ch", { "name": "WVALID(out)", "wave": "0....|....|....1..|..0.." }, { "name": "WDATA(out)", "wave": "x....|....|....444|44x..", "data": ["D0", "D1", "D2", "D14", "D15"] }, { "name": "WLAST(out)", "wave": "0....|....|.......|.10.." }, { "name": "WREADY(in)", "wave": "0....|....|....1..|..0.." } ] ], "head" : { "tick" : "0" }, "foot" : { "tick" : "0" } } 그림 3. DMA operation with burst transfers. At a time, a request reads/writes 16 cycles of data.

    Please verify if the following table is correct using the code provided below.

    +-------+-------------------------------------------------------------------------------------+------------+-----------------------------------------------------------+-----------------------------------------+ | State | Major outputs | Next State | Next state transition condition | Notes | | +---------+--------+---------------------------------------+-------------------+------+ | | | | | ARVALID | RREADY | AWVALID | WVALID | done | | | | +-------+---------+--------+---------------------------------------+-------------------+------+------------+-----------------------------------------------------------+-----------------------------------------+ | IDLE | 0 | 0 | 0 | 0 | 1 | RREQ | (DMA_CMD.start is written as 1) and (DMA_LEN.byte_len!=0) | On moving out, | | | | | | | | | | - Copy DMA_SRC to SRC_ADDR. | | | | | | | | | | - Copy DMA_DST to DST_ADDR | | | | | | | | | | - Copy DMA_LEN to the internal counter | +-------+---------+--------+---------------------------------------+-------------------+------+------------+-----------------------------------------------------------+-----------------------------------------+ | RREQ | 1 | 0 | 0 | 0 | 0 | RDATA | ARREADY=1 | On moving out, | | | | | | | | | | - Increment ARADDR by 4 | | | | | | | | | | | | | | | | | | | | ARLEN = (cnt>=64) ? 'hF : cnt[5:2]-4'h1 | +-------+---------+--------+---------------------------------------+-------------------+------+------------+-----------------------------------------------------------+-----------------------------------------+ | RDATA | 0 | 1 | 0 | 0 | 0 | WREQ | (RVALID=1) & (RLAST) | Push data to FIFO | | | | | | | +------------+-----------------------------------------------------------+-----------------------------------------+ | | | | | | | RDATA | (RVALID) & (!RLAST) | Push data to FIFO | +-------+---------+--------+---------------------------------------+-------------------+------+------------+-----------------------------------------------------------+-----------------------------------------+ | WREQ | 0 | 0 | 1 | 0 | 0 | WDATA | AWREADY=1 | On moving out, | | | | | AWLEN=(cnt>=64) ? 'hF : cnt[5:2]-4'h1 | | | | | - Increment AWADDR by 4 | | | | | | | | | | - Decrement the internal counter by 4 | +-------+---------+--------+---------------------------------------+-------------------+------+------------+-----------------------------------------------------------+-----------------------------------------+ | WDATA | 0 | 0 | 0 | 1 | 0 | RREQ | (WREADY=1) (!WLAST) & (counter!=0) | Pop data from FIFO | | | | | | WLAST=(wcnt=='d0) | | | | Decrement wcnt | | | | | | | +------------+-----------------------------------------------------------+-----------------------------------------+ | | | | | | | IDLE | (WREADY=1) (WLAST) & (counter==0) | Pop data from FIFO | +-------+---------+--------+---------------------------------------+-------------------+------+------------+-----------------------------------------------------------+-----------------------------------------+

    <<StartOfFile:DMAC/RTL/DMAC_FIFO.sv>> module DMAC_FIFO #( parameter DEPTH_LG2 = 4, parameter DATA_WIDTH = 32 ) ( input wire clk, input wire rst_n,

    output wire full_o,
    input wire wren_i,
    input wire [DATA_WIDTH-1:0] wdata_i,
    
    output wire empty_o,
    input wire rden_i,
    output wire [DATA_WIDTH-1:0] rdata_o
    

    );

    localparam FIFO_DEPTH = (1<<DEPTH_LG2);
    
    reg [DATA_WIDTH-1:0] data[FIFO_DEPTH];
    
    reg full, full_n,
                                        empty, empty_n;
    reg [DEPTH_LG2:0] wrptr, wrptr_n,
                                        rdptr, rdptr_n;
    
    // reset entries to all 0s
    always_ff @(posedge clk)
        if (!rst_n) begin
            full <= 1'b0;
            empty <= 1'b1; // empty after as reset
    
            wrptr <= {(DEPTH_LG2+1){1'b0}};
            rdptr <= {(DEPTH_LG2+1){1'b0}};
    
            for (int i=0; i<FIFO_DEPTH; i++) begin
                data[i] <= {DATA_WIDTH{1'b0}};
            end
        end
        else begin
            full <= full_n;
            empty <= empty_n;
    
            wrptr <= wrptr_n;
            rdptr <= rdptr_n;
    
            if (wren_i) begin
                data[wrptr[DEPTH_LG2-1:0]] <= wdata_i;
            end
        end
    
    always_comb begin
        wrptr_n = wrptr;
        rdptr_n = rdptr;
    
        if (wren_i) begin
            wrptr_n = wrptr + 'd1;
        end
    
        if (rden_i) begin
            rdptr_n = rdptr + 'd1;
        end
    
        empty_n = (wrptr_n == rdptr_n);
        full_n = (wrptr_n[DEPTH_LG2]!=rdptr_n[DEPTH_LG2])
                                     &(wrptr_n[DEPTH_LG2-1:0]==rdptr_n[DEPTH_LG2-1:0]);
    
    end
    
    // synthesis translate_off
    always @(posedge clk) begin
        if (full_o & wren_i) begin
            \$display("FIFO overflow");
            @(posedge clk);
            \$finish;
        end
    end
    
    always @(posedge clk) begin
        if (empty_o & rden_i) begin
            \$display("FIFO underflow");
            @(posedge clk);
            \$finish;
        end
    end
    // synthesis translate_on
    
    assign full_o = full;
    assign empty_o = empty;
    assign rdata_o = data[rdptr[DEPTH_LG2-1:0]];
    

    endmodule <<EndOfFile:DMAC/RTL/DMAC_FIFO.sv>>

    <<StartOfFile:DMAC/SIM/TB/DMAC_TOP_TB.sv>> define IP_VER 32'h000 define SRC_ADDR 32'h100 define DST_ADDR 32'h104 define LEN_ADDR 32'h108 define STAT_ADDR 32'h110 define START_ADDR 32'h10c

    `define TIMEOUT_CYCLE 999999 module DMAC_TOP_TB ();

    reg clk;
    reg rst_n;
    
    // clock generation
    initial begin
        clk = 1'b0;
    
        forever #10 clk = !clk;
    end
    
    // reset generation
    initial begin
        rst_n = 1'b0; // active at time 0
    
        repeat (3) @(posedge clk); // after 3 cycles,
        rst_n = 1'b1; // release the reset
    end
    
    // enable waveform dump
    initial begin
        \$dumpvars(0, u_DUT);
        \$dumpfile("dump.vcd");
    end
    

    // timeout initial begin #`TIMEOUT_CYCLE $display("Timeout!"); $finish; end

    APB apb_if (.clk(clk));
    
    AXI_AW_CH aw_ch (.clk(clk));
    AXI_W_CH w_ch (.clk(clk));
    AXI_B_CH b_ch (.clk(clk));
    AXI_AR_CH ar_ch (.clk(clk));
    AXI_R_CH r_ch (.clk(clk));
    
    task test_init();
        int data;
        apb_if.init();
    
        @(posedge rst_n); // wait for a release of the reset
        repeat (10) @(posedge clk); // wait another 10 cycles
    
        apb_if.read(`IP_VER, data);
        \$display("---------------------------------------------------");
        \$display("IP version: %x", data);
        \$display("---------------------------------------------------");
    
        \$display("---------------------------------------------------");
        \$display("Reset value test");
        \$display("---------------------------------------------------");
        apb_if.read(`SRC_ADDR, data);
        if (data===0)
            \$display("DMA_SRC(pass): %x", data);
        else begin
            \$display("DMA_SRC(fail): %x", data);
            @(posedge clk);
            \$finish;
        end
        apb_if.read(`DST_ADDR, data);
        if (data===0)
            \$display("DMA_DST(pass): %x", data);
        else begin
            \$display("DMA_DST(fail): %x", data);
            @(posedge clk);
            \$finish;
        end
        apb_if.read(`LEN_ADDR, data);
        if (data===0)
            \$display("DMA_LEN(pass): %x", data);
        else begin
            \$display("DMA_LEN(fail): %x", data);
            @(posedge clk);
            \$finish;
        end
        apb_if.read(`STAT_ADDR, data);
        if (data===1)
            \$display("DMA_STATUS(pass): %x", data);
        else begin
            \$display("DMA_STATUS(fail): %x", data);
            @(posedge clk);
            \$finish;
        end
    endtask
    
    task test_dma(input int src, input int dst, input int len);
        int data;
        int word;
        realtime elapsed_time;
    
        \$display("---------------------------------------------------");
        \$display("Load data to memory");
        \$display("---------------------------------------------------");
        for (int i=src; i<(src+len); i=i+4) begin
            word = \$random; 
            u_mem.write_word(i, word);
        end
    
        \$display("---------------------------------------------------");
        \$display("Configuration test");
        \$display("---------------------------------------------------");
        apb_if.write(`SRC_ADDR, src);
        apb_if.read(`SRC_ADDR, data);
        if (data===src)
            \$display("DMA_SRC(pass): %x", data);
        else begin
            \$display("DMA_SRC(fail): %x", data);
            @(posedge clk);
            \$finish;
        end
        apb_if.write(`DST_ADDR, dst);
        apb_if.read(`DST_ADDR, data);
        if (data===dst)
            \$display("DMA_DST(pass): %x", data);
        else begin
            \$display("DMA_DST(fail): %x", data);
            @(posedge clk);
            \$finish;
        end
        apb_if.write(`LEN_ADDR, len);
        apb_if.read(`LEN_ADDR, data);
        if (data===len)
            \$display("DMA_LEN(pass): %x", data);
        else begin
            \$display("DMA_LEN(fail): %x", data);
            @(posedge clk);
            \$finish;
        end
    
        \$display("---------------------------------------------------");
        \$display("DMA start");
        \$display("---------------------------------------------------");
        apb_if.write(`START_ADDR, 32'h1);
        elapsed_time = \$realtime;
    
        \$display("---------------------------------------------------");
        \$display("Wait for a DMA completion");
        \$display("---------------------------------------------------");
        data = 0;
        while (data!=1) begin
            apb_if.read(`STAT_ADDR, data);
            repeat (100) @(posedge clk);
        end
        @(posedge clk);
        elapsed_time = \$realtime - elapsed_time;
        \$timeformat(-9, 0, " ns", 10);
        \$display("Elapsed time for DMA: %t", elapsed_time);
    
        \$display("---------------------------------------------------");
        \$display("DMA completed");
        \$display("---------------------------------------------------");
    
        repeat (len) @(posedge clk); // to make sure data is written
    
        \$display("---------------------------------------------------");
        \$display("verify data");
        \$display("---------------------------------------------------");
        for (int i=0; i<len; i=i+4) begin
            logic [31:0] src_word;
            logic [31:0] dst_word;
            src_word = u_mem.read_word(src+i);
            dst_word = u_mem.read_word(dst+i);
            if (src_word!==dst_word) begin
                \$display("Mismatch! (src:%x @%x, dst:%x @%x", src_word, src+i, dst_word, dst+i);
            end
        end
    endtask
    
    int src,
                    dst,
                    len;
    
    // main
    initial begin
        test_init();
    
        src = 'h0000_1000;
        dst = 'h0000_2000;
        len = 'h0100;
        \$display("===================================================");
        \$display("= 1st trial"); 
        \$display("= Copying %x bytes from %x to %x", len, src, dst);
        \$display("===================================================");
        test_dma(src, dst, len);
    
        src = 'h1234_1234;
        dst = 'hABCD_ABCC;
        len = 'h0F00;
        \$display("===================================================");
        \$display("= 2nd trial (long transfer)");
        \$display("= Copying %x bytes from %x to %x", len, src, dst);
        \$display("===================================================");
        test_dma(src, dst, len);
    
        src = 'h4278_0000;
        dst = 'h4278_1000;
        len = 'h0F10;
        \$display("===================================================");
        \$display("= 3rd trial (long transfer-2)");
        \$display("= Copying %x bytes from %x to %x", len, src, dst);
        \$display("===================================================");
        test_dma(src, dst, len);
        \$finish;
    end
    
    
    AXI_SLAVE u_mem (
        .clk (clk),
        .rst_n (rst_n),
    
        .aw_ch (aw_ch),
        .w_ch (w_ch),
        .b_ch (b_ch),
        .ar_ch (ar_ch),
        .r_ch (r_ch)
    );
    
    DMAC_TOP u_DUT (
        .clk (clk),
        .rst_n (rst_n),
    
        // APB interface
        .psel_i (apb_if.psel),
        .penable_i (apb_if.penable),
        .paddr_i (apb_if.paddr[11:0]),
        .pwrite_i (apb_if.pwrite),
        .pwdata_i (apb_if.pwdata),
        .pready_o (apb_if.pready),
        .prdata_o (apb_if.prdata),
        .pslverr_o (apb_if.pslverr),
    
        // AXI AW channel
        .awid_o (aw_ch.awid),
        .awaddr_o (aw_ch.awaddr),
        .awlen_o (aw_ch.awlen),
        .awsize_o (aw_ch.awsize),
        .awburst_o (aw_ch.awburst),
        .awvalid_o (aw_ch.awvalid),
        .awready_i (aw_ch.awready),
    
        // AXI W channel
        .wid_o (w_ch.wid),
        .wdata_o (w_ch.wdata),
        .wstrb_o (w_ch.wstrb),
        .wlast_o (w_ch.wlast),
        .wvalid_o (w_ch.wvalid),
        .wready_i (w_ch.wready),
    
        // AXI B channel
        .bid_i (b_ch.bid),
        .bresp_i (b_ch.bresp),
        .bvalid_i (b_ch.bvalid),
        .bready_o (b_ch.bready),
    
        // AXI AR channel
        .arid_o (ar_ch.arid),
        .araddr_o (ar_ch.araddr),
        .arlen_o (ar_ch.arlen),
        .arsize_o (ar_ch.arsize),
        .arburst_o (ar_ch.arburst),
        .arvalid_o (ar_ch.arvalid),
        .arready_i (ar_ch.arready),
    
        // AXI R channel
        .rid_i (r_ch.rid),
        .rdata_i (r_ch.rdata),
        .rresp_i (r_ch.rresp),
        .rlast_i (r_ch.rlast),
        .rvalid_i (r_ch.rvalid),
        .rready_o (r_ch.rready)
    );
    

    endmodule <<EndOfFile:DMAC/SIM/TB/DMAC_TOP_TB.sv>>

    <StartOfFile:DMAC/RTL/DMAC_CFG.sv>> module DMAC_CFG ( input wire clk, input wire rst_n, // _n means active low

    // AMBA APB interface
    input wire psel_i,
    input wire penable_i,
    input wire [11:0] paddr_i,
    input wire pwrite_i,
    input wire [31:0] pwdata_i,
    output reg pready_o,
    output reg [31:0] prdata_o,
    output reg pslverr_o,
    
    // configuration registers
    output reg [31:0] src_addr_o,
    output reg [31:0] dst_addr_o,
    output reg [15:0] byte_len_o,
    output wire start_o,
    input wire done_i
    

    );

    // Configuration register to read/write
    reg [31:0] src_addr;
    reg [31:0] dst_addr;
    reg [15:0] byte_len;
    
    //----------------------------------------------------------
    // Write
    //----------------------------------------------------------
    // an APB write occurs when PSEL & PENABLE & PWRITE
    // clk : __--__--__--__--__--__--__--__--__--__--
    // psel : ___--------_____________________________
    // penable : _______----_____________________________
    // pwrite : ___--------_____________________________
    // wren : _______----_____________________________
    //
    // DMA start command must be asserted when APB writes 1 to the DMA_CMD
    // register
    // clk : __--__--__--__--__--__--__--__--__--__--
    // psel : ___--------_____________________________
    // penable : _______----_____________________________
    // pwrite : ___--------_____________________________
    // paddr : |DMA_CMD|
    // pwdata : | 1 |
    // start : _______----_____________________________
    
    wire wren = psel_i & penable_i & pwrite_i;
    
    always @(posedge clk) begin
        if (!rst_n) begin
            src_addr <= 32'd0;
            dst_addr <= 32'd0;
            byte_len <= 16'd0;
        end
        else if (wren) begin
            case (paddr_i)
                'h100: src_addr <= pwdata_i[31:0];
                'h104: dst_addr <= pwdata_i[31:0];
                'h108: byte_len <= pwdata_i[15:0];
            endcase
        end
    end
    wire start = wren & (paddr_i=='h10C) & pwdata_i[0];
    
    //----------------------------------------------------------
    // READ
    //----------------------------------------------------------
    // an APB read occurs when PSEL & PENABLE & !PWRITE
    // To make read data a direct output from register,
    // this code shall buffer the muxed read data into a register
    // in the SETUP cycle (PSEL & !PENABLE)
    // clk : __--__--__--__--__--__--__--__--__--__--
    // psel : ___--------_____________________________
    // penable : _______----_____________________________
    // pwrite : ________________________________________
    // reg update : ___----_________________________________
    // prdata : |DATA
    
    reg [31:0] rdata;
    
    always @(posedge clk) begin
        if (!rst_n) begin
            rdata <= 32'd0;
        end
        else if (psel_i & !penable_i & !pwrite_i) begin // in the setup cycle in the APB state diagram
            case (paddr_i)
                'h0: rdata <= 32'h0001_2024;
                'h100: rdata <= src_addr;
                'h104: rdata <= dst_addr;
                'h108: rdata <= {16'd0, byte_len};
                'h110: rdata <= {31'd0, done_i};
                default: rdata <= 32'd0;
            endcase
        end
    end
    
    // output assignments
    assign pready_o = 1'b1;
    assign prdata_o = rdata;
    assign pslverr_o = 1'b0;
    
    assign src_addr_o = src_addr;
    assign dst_addr_o = dst_addr;
    assign byte_len_o = byte_len;
    assign start_o = start;
    

    endmodule <<EndOfFile:DMAC/RTL/DMAC_CFG.sv>>

    <<StartOfFile:DMAC/RTL/DMAC_TOP.sv>> module DMAC_TOP ( input wire clk, input wire rst_n, // _n means active low

    // AMBA APB interface
    input wire psel_i,
    input wire penable_i,
    input wire [11:0] paddr_i,
    input wire pwrite_i,
    input wire [31:0] pwdata_i,
    output reg pready_o,
    output reg [31:0] prdata_o,
    output reg pslverr_o,
    
    // AMBA AXI interface (AW channel)
    output wire [3:0] awid_o,
    output wire [31:0] awaddr_o,
    output wire [3:0] awlen_o,
    output wire [2:0] awsize_o,
    output wire [1:0] awburst_o,
    output wire awvalid_o,
    input wire awready_i,
    
    // AMBA AXI interface (AW channel)
    output wire [3:0] wid_o,
    output wire [31:0] wdata_o,
    output wire [3:0] wstrb_o,
    output wire wlast_o,
    output wire wvalid_o,
    input wire wready_i,
    
    // AMBA AXI interface (B channel)
    input wire [3:0] bid_i,
    input wire [1:0] bresp_i,
    input wire bvalid_i,
    output wire bready_o,
    
    // AMBA AXI interface (AR channel)
    output wire [3:0] arid_o,
    output wire [31:0] araddr_o,
    output wire [3:0] arlen_o,
    output wire [2:0] arsize_o,
    output wire [1:0] arburst_o,
    output wire arvalid_o,
    input wire arready_i,
    
    // AMBA AXI interface (R channel)
    input wire [3:0] rid_i,
    input wire [31:0] rdata_i,
    input wire [1:0] rresp_i,
    input wire rlast_i,
    input wire rvalid_i,
    output wire rready_o
    

    );

    wire [31:0] src_addr;
    wire [31:0] dst_addr;
    wire [15:0] byte_len;
    wire start;
    wire done;
    
    DMAC_CFG u_cfg(
        .clk (clk),
        .rst_n (rst_n),
    
        // AMBA APB interface
        .psel_i (psel_i),
        .penable_i (penable_i),
        .paddr_i (paddr_i),
        .pwrite_i (pwrite_i),
        .pwdata_i (pwdata_i),
        .pready_o (pready_o),
        .prdata_o (prdata_o),
        .pslverr_o (pslverr_o),
    
        .src_addr_o (src_addr),
        .dst_addr_o (dst_addr),
        .byte_len_o (byte_len),
        .start_o (start),
        .done_i (done)
    );
    
    DMAC_ENGINE u_engine(
        .clk (clk),
        .rst_n (rst_n),
    
        // configuration registers
        .src_addr_i (src_addr),
        .dst_addr_i (dst_addr),
        .byte_len_i (byte_len),
        .start_i (start),
        .done_o (done),
    
        // AMBA AXI interface (AW channel)
        .awid_o (awid_o),
        .awaddr_o (awaddr_o),
        .awlen_o (awlen_o),
        .awsize_o (awsize_o),
        .awburst_o (awburst_o),
        .awvalid_o (awvalid_o),
        .awready_i (awready_i),
    
        // AMBA AXI interface (W channel)
        .wid_o (wid_o),
        .wdata_o (wdata_o),
        .wstrb_o (wstrb_o),
        .wlast_o (wlast_o),
        .wvalid_o (wvalid_o),
        .wready_i (wready_i),
    
        // AMBA AXI interface (B channel)
        .bid_i (bid_i),
        .bresp_i (bresp_i),
        .bvalid_i (bvalid_i),
        .bready_o (bready_o),
    
        // AMBA AXI interface (AR channel)
        .arid_o (arid_o),
        .araddr_o (araddr_o),
        .arlen_o (arlen_o),
        .arsize_o (arsize_o),
        .arburst_o (arburst_o),
        .arvalid_o (arvalid_o),
        .arready_i (arready_i),
    
        // AMBA AXI interface (R channel)
        .rid_i (rid_i),
        .rdata_i (rdata_i),
        .rresp_i (rresp_i),
        .rlast_i (rlast_i),
        .rvalid_i (rvalid_i),
        .rready_o (rready_o)
    );
    

    endmodule <<EndOfFile:DMAC/RTL/DMAC_TOP.sv>>

    <<StartOfFile:DMAC/SIM/TB/AXI_INTF.sv>> `include "../TB/AXI_TYPEDEF.svh"

    interface AXI_AW_CH #( parameter ADDR_WIDTH = AXI_ADDR_WIDTH, parameter ID_WIDTH = AXI_ID_WIDTH ) ( input clk ); logic awvalid; logic awready; logic [ID_WIDTH-1:0] awid; logic [ADDR_WIDTH-1:0] awaddr; logic [3:0] awlen; logic [2:0] awsize; logic [1:0] awburst;

    endinterface

    interface AXI_W_CH #( parameter DATA_WIDTH = AXI_DATA_WIDTH, parameter ID_WIDTH = AXI_ID_WIDTH ) ( input clk ); logic wvalid; logic wready; logic [ID_WIDTH-1:0] wid; logic [DATA_WIDTH-1:0] wdata; logic [DATA_WIDTH/8-1:0] wstrb; logic wlast;

    endinterface

    interface AXI_B_CH #( parameter ID_WIDTH = `AXI_ID_WIDTH ) ( input clk ); logic bvalid; logic bready; logic [ID_WIDTH-1:0] bid; logic [1:0] bresp;

    endinterface

    interface AXI_AR_CH #( parameter ADDR_WIDTH = AXI_ADDR_WIDTH, parameter ID_WIDTH = AXI_ID_WIDTH ) ( input clk ); logic arvalid; logic arready; logic [ID_WIDTH-1:0] arid; logic [ADDR_WIDTH-1:0] araddr; logic [3:0] arlen; logic [2:0] arsize; logic [1:0] arburst;

    endinterface

    interface AXI_R_CH #( parameter DATA_WIDTH = AXI_DATA_WIDTH, parameter ID_WIDTH = AXI_ID_WIDTH ) ( input clk ); logic rvalid; logic rready; logic [ID_WIDTH-1:0] rid; logic [DATA_WIDTH-1:0] rdata; logic [1:0] rresp; logic rlast;

    endinterface

    interface APB ( input clk ); logic psel; logic penable; logic [31:0] paddr; logic pwrite; logic [31:0] pwdata; logic pready; logic [31:0] prdata; logic pslverr;

    modport master (
        input clk,
        input pready, prdata, pslverr,
        output psel, penable, paddr, pwrite, pwdata
    );
    
    task init();
        psel = 1'b0;
        penable = 1'b0;
        paddr = 32'd0;
        pwrite = 1'b0;
        pwdata = 32'd0;
    endtask
    
    task write(input int addr,
               input int data);
        #1
        psel = 1'b1;
        penable = 1'b0;
        paddr = addr;
        pwrite = 1'b1;
        pwdata = data;
        @(posedge clk);
        #1
        penable = 1'b1;
        @(posedge clk);
    
        while (pready==1'b0) begin
            @(posedge clk);
        end
    
        psel = 1'b0;
        penable = 1'b0;
        paddr = 'hX;
        pwrite = 1'bx;
        pwdata = 'hX;
    endtask
    
    task read(input int addr,
              output int data);
        #1
        psel = 1'b1;
        penable = 1'b0;
        paddr = addr;
        pwrite = 1'b0;
        pwdata = 'hX;
        @(posedge clk);
        #1
        penable = 1'b1;
        @(posedge clk);
    
        while (pready==1'b0) begin
            @(posedge clk);
        end
        data = prdata;
    
        psel = 1'b0;
        penable = 1'b0;
        paddr = 'hX;
        pwrite = 1'bx;
        pwdata = 'hX;
    endtask
    

    endinterface <<EndOfFile:DMAC/SIM/TB/AXI_INTF.sv>>

    <<StartOfFile:DMAC/SIM/TB/AXI_SLAVE.sv>> `include "../TB/AXI_TYPEDEF.svh"

    module AXI_SLAVE #( parameter ADDR_WIDTH = 16, parameter DATA_WIDTH = AXI_DATA_WIDTH, parameter ID_WIDTH = AXI_ID_WIDTH, parameter AWREADY_DELAY = 1, parameter ARREADY_DELAY = 1, parameter AR2R_DELAY = 50 ) ( input wire clk, input wire rst_n, // _n means active low

    AXI_AW_CH aw_ch,
    AXI_W_CH w_ch,
    AXI_B_CH b_ch,
    AXI_AR_CH ar_ch,
    AXI_R_CH r_ch
    

    );

    localparam DATA_DEPTH = 1<<ADDR_WIDTH;
    
    logic [7:0] mem[DATA_DEPTH];
    
    function void write_byte(int addr, input bit [7:0] wdata);
        mem[addr] = wdata;
    endfunction
    
    function void write_word(int addr, input bit [31:0] wdata);
        for (int i=0; i<4; i++) begin
            write_byte(addr+i, wdata[8*i +: 8]); // [i*8+7:i*8]
        end
    endfunction
    
    function bit [7:0] read_byte(int addr);
        read_byte = mem[addr];
    endfunction
    
    function bit [31:0] read_word(int addr);
        for (int i=0; i<4; i++) begin
            read_word[8*i +: 8] = read_byte(addr+i);// [i*8+7:i*8]
        end
    endfunction
    
    //----------------------------------------------------------
    // write channels (AW, W, B)
    //----------------------------------------------------------
    localparam logic [1:0] S_W_IDLE = 0,
                                S_W_AWREADY = 1,
                                S_W_BURST = 2,
                                S_W_RESP = 3;
    
    logic [1:0] wstate, wstate_n;
    logic [7:0] wcnt, wcnt_n;
    
    logic [ADDR_WIDTH-1:0] waddr, waddr_n;
    logic [ID_WIDTH-1:0] wid, wid_n;
    logic [3:0] wlen, wlen_n;
    
    always_ff @(posedge clk)
        if (!rst_n) begin
            wstate <= S_W_IDLE;
    
            wcnt <= 8'd0;
            waddr <= {ADDR_WIDTH{1'b0}};
            wid <= {ID_WIDTH{1'b0}};
            wlen <= 4'd0;
        end
        else begin
            wstate <= wstate_n;
    
            wcnt <= wcnt_n;
            waddr <= waddr_n;
            wid <= wid_n;
            wlen <= wlen_n;
        end
    
    always @(*) begin
        wstate_n = wstate;
    
        wcnt_n = wcnt;
        waddr_n = waddr;
        wid_n = wid;
        wlen_n = wlen;
    
        aw_ch.awready = 1'b0;
        w_ch.wready = 1'b0;
        b_ch.bvalid = 1'b0;
    
        case (wstate)
            S_W_IDLE: begin
                if (aw_ch.awvalid) begin
                    if (AWREADY_DELAY == 0) begin
                        waddr_n = aw_ch.awaddr;
                        wid_n = aw_ch.awid;
                        wlen_n = aw_ch.awlen;
                        aw_ch.awready = 1'b1;
                        wstate_n = S_W_BURST;
                    end
                    else begin
                        wcnt_n = AWREADY_DELAY-1;
                        wstate_n = S_W_AWREADY;
                    end
                end
            end
            S_W_AWREADY: begin
                if (wcnt==0) begin
                    waddr_n = aw_ch.awaddr;
                    wid_n = aw_ch.awid;
                    wlen_n = aw_ch.awlen;
                    aw_ch.awready = 1'b1;
                    wstate_n = S_W_BURST;
                end
                else begin
                    wcnt_n = wcnt - 8'd1;
                end
            end
            S_W_BURST: begin
                w_ch.wready = 1'b1;
                if (w_ch.wvalid) begin
                    for (int i=0; i<DATA_WIDTH/8; i++) begin
                        write_byte(waddr + i, w_ch.wdata[i*8 +: 8]); // [i*8+7:i*8]
                    end
                    waddr_n = waddr + (DATA_WIDTH/8);
                    if (wlen==4'd0) begin
                        wstate_n = S_W_RESP;
                    end
                    else begin
                        wlen_n = wlen - 4'd1;
                    end
                end
            end
            S_W_RESP: begin
                b_ch.bvalid = 1'b1;
                if (b_ch.bready) begin
                    wstate_n = S_W_IDLE;
                end
            end
        endcase
    end
    
    //----------------------------------------------------------
    // read channel (AR, R)
    //----------------------------------------------------------
    localparam logic [1:0] S_R_IDLE = 0,
                                S_R_ARREADY = 1,
                                S_R_DELAY = 2,
                                S_R_BURST = 3;
    
    logic [1:0] rstate, rstate_n;
    logic [7:0] rcnt, rcnt_n;
    
    logic [ADDR_WIDTH-1:0] raddr, raddr_n;
    logic [ID_WIDTH-1:0] rid, rid_n;
    logic [3:0] rlen, rlen_n;
    
    always_ff @(posedge clk)
        if (!rst_n) begin
            rstate <= S_R_IDLE;
    
            rcnt <= 8'd0;
            raddr <= {ADDR_WIDTH{1'b0}};
            rid <= {ID_WIDTH{1'b0}};
            rlen <= 4'd0;
        end
        else begin
            rstate <= rstate_n;
    
            rcnt <= rcnt_n;
            raddr <= raddr_n;
            rid <= rid_n;
            rlen <= rlen_n;
        end
    
    always_comb begin
        rstate_n = rstate;
    
        rcnt_n = rcnt;
        raddr_n = raddr;
        rid_n = rid;
        rlen_n = rlen;
    
        ar_ch.arready = 1'b0;
        r_ch.rvalid = 1'b0;
        r_ch.rlast = 1'b0;
    
        case (rstate)
            S_R_IDLE: begin
                if (ar_ch.arvalid) begin
                    if (ARREADY_DELAY == 0) begin
                        raddr_n = ar_ch.araddr;
                        rid_n = ar_ch.arid;
                        rlen_n = ar_ch.arlen;
                        ar_ch.arready = 1'b1;
    
                        rcnt_n = AR2R_DELAY - 1;
                        rstate_n = S_R_DELAY;
                    end
                    else begin
                        rcnt_n = ARREADY_DELAY-1;
                        rstate_n = S_R_ARREADY;
                    end
                end
            end
            S_R_ARREADY: begin
                if (rcnt==0) begin
                    raddr_n = ar_ch.araddr;
                    rid_n = ar_ch.arid;
                    rlen_n = ar_ch.arlen;
                    ar_ch.arready = 1'b1;
    
                    rcnt_n = AR2R_DELAY - 1;
                    rstate_n = S_R_DELAY;
                end
                else begin
                    rcnt_n = rcnt - 8'd1;
                end
            end
            S_R_DELAY: begin
                if (rcnt==0) begin
                    rstate_n = S_R_BURST;
                end
                else begin
                    rcnt_n = rcnt - 8'd1;
                end
            end
            S_R_BURST: begin
                r_ch.rvalid = 1'b1;
                r_ch.rlast = (rlen==4'd0);
                for (int i=0; i<DATA_WIDTH/8; i++) begin
                    r_ch.rdata[i*8 +: 8] = read_byte(raddr + i); // [i*8+7:i*8]
                end
                if (r_ch.rready) begin
                    raddr_n = raddr + (DATA_WIDTH/8);
                    if (rlen==4'd0) begin
                        rstate_n = S_R_IDLE;
                    end
                    else begin
                        rlen_n = rlen - 4'd1;
                    end
                end
            end
        endcase
    end
    
    // output assignments
    assign b_ch.bid = wid;
    assign b_ch.bresp = 2'd0;
    assign r_ch.rid = rid;
    assign r_ch.rresp = 2'd0;
    

    endmodule <<EndOfFile:DMAC/SIM/TB/AXI_SLAVE.sv>>

    <<StartOfFile:DMAC/SIM/TB/AXI_TYPEDEF.svh>> ifndef __AXI_TYPEDEF_SVH__ define AXI_TYPEDEF_SVH

    define AXI_ADDR_WIDTH 32 define AXI_DATA_WIDTH 32 `define AXI_ID_WIDTH 4

    `endif /* AXI_TYPEDEF_SVH */ <<EndOfFile:DMAC/SIM/TB/AXI_TYPEDEF.svh>>

  14. Assistant

    Identifying the cause of the data mismatch requires a thorough investigation of the DMAC_ENGINE module and related components. Here are several areas to investigate:

    1. Correct Addressing and Byte Length Configurations:

      • Ensure the source (src_addr_i) and destination (dst_addr_i) addresses, as well as the byte length (byte_len_i), are correctly set up.
      • Check that the addresses are aligned if the protocol or memory requires it.
    2. State Machine Transitions:

      • Review the state machine transitions between S_IDLE, S_RREQ, S_RDATA, S_WREQ, and S_WDATA states.
      • Verify that the transitions happen as expected and under the right conditions, especially from data read (S_RDATA) to data write (S_WDATA) states.
    3. FIFO Buffer Management:

      • Inspect the FIFO control logic, specifically how fifo_full and fifo_empty signals are handled.
      • Ensure that fifo_wren is asserted only when there is valid data to write to the FIFO and when the FIFO is not full.
      • Similarly, check that fifo_rden is asserted to read data from the FIFO only when the FIFO is not empty.
      • Validate proper incrementing and wrapping of read and write pointers.
    4. AXI Interface Transactions:

      • Check that AXI transactions follow the protocol correctly. This includes proper assertions of arvalid, awvalid, wvalid, and managing the rready and wready signals appropriately.
      • Ensure that wlast is correctly asserted at the end of a write transaction and that rlast is handled properly.
    5. Data Integrity During Transfer:

      • Ensure data read into the FIFO is correctly passed to the FIFO write logic. Data corruption can happen if there are timing issues or incorrect handling of the AXI data and control signals.
      • Verify that the correct data width is used and that no bits are inadvertently altered or dropped during transfers.
    6. Testing and Simulation:

      • Extensively simulate the DMAC operation, paying close attention to how data enters and leaves the FIFO and the AXI interface transactions.
      • Use assertions to catch any unexpected behavior or illegal states within the DMAC.
    7. Hardware Debugging:

      • If testing on actual hardware, use debugging tools available in your FPGA or ASIC environment, such as ILA (Integrated Logic Analyzer), to capture real-time traces of signals.
    8. Software Configurations:

      • Double-check the software or firmware that sets up the DMA transfers to ensure that it correctly configures all necessary registers and that there is no discrepancy between expected and programmed behavior.

    Finding the root cause of data mismatches often requires iterative debugging and can involve both the hardware design and the software driving the DMA operations.