error: stray '\342' in program Serial.println(“ESP-NOW initialization failed”); in the…
- User
error: stray '\342' in program Serial.println(“ESP-NOW initialization failed”); in the code below #include <esp_now.h>
// MAC address of the secondary ESP32 uint8_t secondaryMacAddress[] = { 0x00, 0x00, 0x00, 0x00, 0x00, 0x00 };
// Variables for SPI communication // Modify as per your specific hardware setup const int spiClk = 14; // SPI clock pin const int spiMiso = 12; // SPI MISO pin const int spiMosi = 13; // SPI MOSI pin const int spiCs = 15; // SPI CS pin
void onDataRecv(const uint8_t* mac, const uint8_t* data, int len) { if (len > 0) { // Send the received data over SPI to the screen for (int i = 0; i < len; i++) { // Replace the following line with your own SPI code to send data to the screen // spiTransfer(data[i]); } } }
void setup() { // Set up SPI pins and communication pinMode(spiClk, OUTPUT); pinMode(spiMiso, OUTPUT); pinMode(spiMosi, OUTPUT); pinMode(spiCs, OUTPUT);
// Initialize SPI as Slave SPI.begin(spiClk, spiMiso, spiMosi, spiCs); SPI.setHwCs(true);
// Initialize ESP-NOW if (esp_now_init() != 0) { Serial.println(“ESP-NOW initialization failed”); while (true) { delay(1000); } }
// Register callback for receiving data esp_now_register_recv_cb(onDataRecv);
// Add the secondary ESP32 as a peer esp_now_peer_info_t peer; memcpy(peer.peer_addr, secondaryMacAddress, 6); peer.channel = 0; peer.encrypt = false; if (esp_now_add_peer(&peer) != ESP_OK) { Serial.println(“Failed to add peer”); while (true) { delay(1000); } } }
void loop() { // Check for incoming SPI data // Modify the following code to read SPI data as per your hardware setup uint8_t receivedData = 0; if (SPI.available()) { receivedData = SPI.transfer(0x00); }
// Send the received SPI data over ESP-NOW to the secondary ESP32 esp_now_send(secondaryMacAddress, &receivedData, sizeof(receivedData));
delay(10); // Adjust delay as per your requirements }
- Assistant
The error "stray '\342' in program" occurs because you are using curly quotes (“ ”) instead of straight quotes (" ") around the string "ESP-NOW initialization failed".
To fix the error, replace the curly quotes with straight quotes in both instances in your code. Here's the corrected code:
error: stray '\342' in program Serial.println("ESP-NOW initialization failed"); in the code below #include <esp_now.h> // MAC address of the secondary ESP32 uint8_t secondaryMacAddress[] = { 0x00, 0x00, 0x00, 0x00, 0x00, 0x00 }; // Variables for SPI communication // Modify as per your specific hardware setup const int spiClk = 14; // SPI clock pin const int spiMiso = 12; // SPI MISO pin const int spiMosi = 13; // SPI MOSI pin const int spiCs = 15; // SPI CS pin void onDataRecv(const uint8_t* mac, const uint8_t* data, int len) { if (len > 0) { // Send the received data over SPI to the screen for (int i = 0; i < len; i++) { // Replace the following line with your own SPI code to send data to the screen // spiTransfer(data[i]); } } } void setup() { // Set up SPI pins and communication pinMode(spiClk, OUTPUT); pinMode(spiMiso, OUTPUT); pinMode(spiMosi, OUTPUT); pinMode(spiCs, OUTPUT); // Initialize SPI as Slave SPI.begin(spiClk, spiMiso, spiMosi, spiCs); SPI.setHwCs(true); // Initialize ESP-NOW if (esp_now_init() != 0) { Serial.println("ESP-NOW initialization failed"); while (true) { delay(1000); } } // Register callback for receiving data esp_now_register_recv_cb(onDataRecv); // Add the secondary ESP32 as a peer esp_now_peer_info_t peer; memcpy(peer.peer_addr, secondaryMacAddress, 6); peer.channel = 0; peer.encrypt = false; if (esp_now_add_peer(&peer) != ESP_OK) { Serial.println("Failed to add peer"); while (true) { delay(1000); } } } void loop() { // Check for incoming SPI data // Modify the following code to read SPI data as per your hardware setup uint8_t receivedData = 0; if (SPI.available()) { receivedData = SPI.transfer(0x00); } // Send the received SPI data over ESP-NOW to the secondary ESP32 esp_now_send(secondaryMacAddress, &receivedData, sizeof(receivedData)); delay(10); // Adjust delay as per your requirements } - User
use #include <ESP32SPISlave.h> to write me arduino code, i need to read out spi data from a RP2040 microcontroller that sends data to SPI screen. I want to read that SPI data and retransmit this with ESP NOW to a ESP32 Slave that can sho that data on another spi screen
- Assistant
Sure! Here's an example Arduino code that uses the
ESP32SPISlavelibrary to read SPI data from an RP2040 microcontroller and retransmit it using ESP-NOW to an ESP32 Slave that can show the data on another SPI screen:#include <ESP32SPISlave.h> #include <esp_now.h> // MAC address of the secondary ESP32 uint8_t secondaryMacAddress[] = { 0x00, 0x00, 0x00, 0x00, 0x00, 0x00 }; // Variables for SPI communication // Modify as per your specific hardware setup const int spiClk = 14; // SPI clock pin const int spiMiso = 12; // SPI MISO pin const int spiMosi = 13; // SPI MOSI pin const int spiCs = 15; // SPI CS pin ESP32SPISlave spiSlave; void onDataRecv(const uint8_t* mac, const uint8_t* data, int len) { if (len > 0) { // Send the received data over SPI to the screen for (int i = 0; i < len; i++) { spiSlave.write(data[i]); } } } void setup() { // Set up SPI pins and communication pinMode(spiClk, OUTPUT); pinMode(spiMiso, OUTPUT); pinMode(spiMosi, OUTPUT); pinMode(spiCs, OUTPUT); // Initialize SPI as Slave spiSlave.setSCK(spiClk); spiSlave.setMISO(spiMiso); spiSlave.setMOSI(spiMosi); spiSlave.setSS(spiCs); spiSlave.setHwCs(true); spiSlave.begin(); // Initialize ESP-NOW if (esp_now_init() != 0) { Serial.println("ESP-NOW initialization failed"); while (true) { delay(1000); } } // Register callback for receiving data esp_now_register_recv_cb(onDataRecv); // Add the secondary ESP32 as a peer esp_now_peer_info_t peer; memcpy(peer.peer_addr, secondaryMacAddress, 6); peer.channel = 0; peer.encrypt = false; if (esp_now_add_peer(&peer) != ESP_OK) { Serial.println("Failed to add peer"); while (true) { delay(1000); } } } void loop() { // Check for incoming SPI data while (spiSlave.available()) { uint8_t receivedData = spiSlave.read(); // Send the received SPI data over ESP-NOW to the secondary ESP32 esp_now_send(secondaryMacAddress, &receivedData, sizeof(receivedData)); } delay(10); // Adjust delay as per your requirements }Make sure to install the
ESP32SPISlavelibrary in your Arduino IDE before uploading the code to your ESP32 device.Remember to adjust the SPI pins (
spiClk,spiMiso,spiMosi,spiCs) and the secondary ESP32's MAC address (secondaryMacAddress) according to your specific hardware setup. Additionally, replace the placeholder code inside theonDataRecvfunction with your own code to transmit the received data to the desired SPI screen.Let me know if you have any further questions!
- User
replace “ and ” with "
- Assistant
Certainly! Here's the modified code with the curly quotes replaced with straight quotes:
#include <ESP32SPISlave.h> #include <esp_now.h> // MAC address of the secondary ESP32 uint8_t secondaryMacAddress[] = { 0x00, 0x00, 0x00, 0x00, 0x00, 0x00 }; // Variables for SPI communication // Modify as per your specific hardware setup const int spiClk = 14; // SPI clock pin const int spiMiso = 12; // SPI MISO pin const int spiMosi = 13; // SPI MOSI pin const int spiCs = 15; // SPI CS pin ESP32SPISlave spiSlave; void onDataRecv(const uint8_t* mac, const uint8_t* data, int len) { if (len > 0) { // Send the received data over SPI to the screen for (int i = 0; i < len; i++) { spiSlave.write(data[i]); } } } void setup() { // Set up SPI pins and communication pinMode(spiClk, OUTPUT); pinMode(spiMiso, OUTPUT); pinMode(spiMosi, OUTPUT); pinMode(spiCs, OUTPUT); // Initialize SPI as Slave spiSlave.setSCK(spiClk); spiSlave.setMISO(spiMiso); spiSlave.setMOSI(spiMosi); spiSlave.setSS(spiCs); spiSlave.setHwCs(true); spiSlave.begin(); // Initialize ESP-NOW if (esp_now_init() != 0) { Serial.println("ESP-NOW initialization failed"); while (true) { delay(1000); } } // Register callback for receiving data esp_now_register_recv_cb(onDataRecv); // Add the secondary ESP32 as a peer esp_now_peer_info_t peer; memcpy(peer.peer_addr, secondaryMacAddress, 6); peer.channel = 0; peer.encrypt = false; if (esp_now_add_peer(&peer) != ESP_OK) { Serial.println("Failed to add peer"); while (true) { delay(1000); } } } void loop() { // Check for incoming SPI data while (spiSlave.available()) { uint8_t receivedData = spiSlave.read(); // Send the received SPI data over ESP-NOW to the secondary ESP32 esp_now_send(secondaryMacAddress, &receivedData, sizeof(receivedData)); } delay(10); // Adjust delay as per your requirements }Make sure to install the
ESP32SPISlavelibrary in your Arduino IDE before uploading the code to your ESP32 device.Remember to adjust the SPI pins (
spiClk,spiMiso,spiMosi,spiCs) and the secondary ESP32's MAC address (secondaryMacAddress) according to your specific hardware setup. Additionally, replace the placeholder code inside theonDataRecvfunction with your own code to transmit the received data to the desired SPI screen.Let me know if you have any further questions!
- User
use following code to to write me arduino code, i need to read out spi data from a RP2040 microcontroller that sends data to SPI screen. I want to read that SPI data and retransmit this with ESP NOW to a ESP32 Slave that can sho that data on another spi screen : #include <ESP32SPISlave.h>
ESP32SPISlave slave;
static constexpr uint32_t BUFFER_SIZE {32}; uint8_t spi_slave_tx_buf[BUFFER_SIZE]; uint8_t spi_slave_rx_buf[BUFFER_SIZE];
void setup() { Serial.begin(115200); delay(2000);
// begin() after setting // HSPI = CS: 15, CLK: 14, MOSI: 13, MISO: 12 -> default // VSPI = CS: 5, CLK: 18, MOSI: 23, MISO: 19 slave.setDataMode(SPI_MODE0); slave.begin(); // slave.begin(VSPI); // you can use VSPI like this // clear buffers memset(spi_slave_tx_buf, 0, BUFFER_SIZE); memset(spi_slave_rx_buf, 0, BUFFER_SIZE);}
void loop() { // if there is no transaction in queue, add transaction if (slave.remained() == 0) { slave.queue(spi_slave_rx_buf, spi_slave_tx_buf, BUFFER_SIZE); }
// if transaction has completed from master, // available() returns size of results of transaction, // and buffer is automatically updated while (slave.available()) { // show received data for (size_t i = 0; i < slave.size(); ++i) { printf("%d ", spi_slave_rx_buf[i]); } printf("\n"); // copy received bytes to tx buffer memcpy(spi_slave_tx_buf, spi_slave_rx_buf, BUFFER_SIZE); String str = (char*)spi_slave_rx_buf; Serial.println(str); slave.pop(); }}
- Assistant
Certainly! Here's the modified code that reads SPI data from an RP2040 microcontroller using the
ESP32SPISlavelibrary and retransmits it using ESP-NOW to an ESP32 Slave that displays the data on another SPI screen:#include <ESP32SPISlave.h> #include <esp_now.h> ESP32SPISlave spiSlave; // MAC address of the secondary ESP32 uint8_t secondaryMacAddress[] = { 0x00, 0x00, 0x00, 0x00, 0x00, 0x00 }; void onDataRecv(const uint8_t* mac, const uint8_t* data, int len) { if (len > 0) { // Write the received data to the SPI screen SPI.transferBytes(data, NULL, len); } } void setup() { Serial.begin(115200); delay(2000); // Set up SPI pins and communication SPI.begin(); SPI.beginTransaction(SPISettings(1000000, MSBFIRST, SPI_MODE0)); // Initialize ESP-NOW if (esp_now_init() != 0) { Serial.println("ESP-NOW initialization failed"); while (true) { delay(1000); } } // Register callback for receiving data esp_now_register_recv_cb(onDataRecv); // Add the secondary ESP32 as a peer esp_now_peer_info_t peer; memcpy(peer.peer_addr, secondaryMacAddress, 6); peer.channel = 0; peer.encrypt = false; if (esp_now_add_peer(&peer) != ESP_OK) { Serial.println("Failed to add peer"); while (true) { delay(1000); } } // Initialize SPI as Slave spiSlave.setMISO(12); // Set MISO pin spiSlave.setHwCs(true); // Use hardware CS pin spiSlave.begin(); } void loop() { // Check if there is incoming SPI data if (spiSlave.available()) { uint8_t receivedData = spiSlave.read(); // Send the received SPI data over ESP-NOW to the secondary ESP32 esp_now_send(secondaryMacAddress, &receivedData, sizeof(receivedData)); } delay(10); // Adjust delay as per your requirements }Make sure to update the MAC address (
secondaryMacAddress) to the MAC address of your secondary ESP32 device.In this modified code, the
onDataRecvfunction writes the received data to the SPI screen. The SPI pins are set up in thesetupfunction, and the ESP-NOW initialization, callback registration, and peer addition are also performed insetup.Let me know if you have any further questions!