i want to make a transparent wireles i2c bus using two esp32 and espnow, using one esp32…
- User
i want to make a transparent wireles i2c bus using two esp32 and espnow, using one esp32 as i2c receiver and one esp32 as i2 transmitter so i can have raw i2c data transmited wireles, how can i do this
- Assistant
To create a transparent wireless I2C bus using two ESP32 boards and ESP-NOW, with one ESP32 acting as the I2C receiver and the other as the I2C transmitter, follow these steps:
- Set up the Arduino IDE for ESP32 development by installing the necessary board definitions and libraries.
- Connect the hardware as follows:
- ESP32 Receiver:
- Connect SDA and SCL pins to the respective I2C data and clock lines of the I2C device you want to interface.
- Connect GND and VCC pins.
- ESP32 Transmitter:
- Connect SDA and SCL pins to the corresponding pins on the ESP32 receiver.
- Connect GND and VCC pins.
- ESP32 Receiver:
- Flash the appropriate firmware to the ESP32 receiver and transmitter using the Arduino IDE.
- On the ESP32 receiver, include the necessary libraries and define ESP-NOW callbacks and I2C functions. Here's an example code snippet:
#include <Wire.h> #include <esp_now.h> void onDataReceived(const uint8_t *mac, const uint8_t *data, int len) { // Forward the received data to the I2C bus Wire.beginTransmission(I2C_ADDRESS); for (int i = 0; i < len; i++) { Wire.write(data[i]); } Wire.endTransmission(); } void setup() { Wire.begin(I2C_ADDRESS); // Set the receiver's I2C address Wire.onReceive([](int) { while (Wire.available()) { // Read and discard received data to keep I2C bus buffers clear Wire.read(); } }); esp_now_init(); esp_now_register_recv_cb(onDataReceived); } void loop() { // Any additional logic can be added here }- On the ESP32 transmitter, include the necessary libraries and define ESP-NOW callbacks and I2C functions. Here's an example code snippet:
#include <Wire.h> #include <esp_now.h> void onDataReceived(const uint8_t *mac, const uint8_t *data, int len) { // Forward the received data to the I2C bus Wire.beginTransmission(I2C_ADDRESS); for (int i = 0; i < len; i++) { Wire.write(data[i]); } Wire.endTransmission(); } void setup() { Wire.begin(); // Start the transmitter's I2C bus esp_now_init(); esp_now_register_send_cb([](const uint8_t*, esp_now_send_status_t) {}); } void loop() { // Read data from the I2C bus Wire.requestFrom(I2C_ADDRESS, DATA_LENGTH); uint8_t data[DATA_LENGTH]; uint8_t dataLen = 0; while (Wire.available()) { data[dataLen++] = Wire.read(); } // Send the data over ESP-NOW esp_now_send(ESP_NOW_MAC_ADDR_ANY, data, dataLen); delay(DELAY_MS); }- Adjust the I2C address, data length, and delay values in the code to match your requirements.
- Compile and upload the code to both ESP32 boards, ensuring they have unique MAC addresses.
- Power on both ESP32 boards.
- The ESP32 transmitter will wirelessly transmit raw I2C data to the ESP32 receiver, allowing you to communicate with the I2C device connected to the receiver wirelessly.
- User
this looks prommesing, can you make me both programs for arduino ide including all needed library
- Assistant
Certainly! Here are the complete programs for both the ESP32 receiver and ESP32 transmitter, including the necessary libraries:
ESP32 Receiver:
#include <Wire.h> #include <esp_now.h> #define I2C_ADDRESS 8 void onDataReceived(const uint8_t *mac, const uint8_t *data, int len) { // Forward the received data to the I2C bus Wire.beginTransmission(I2C_ADDRESS); for (int i = 0; i < len; i++) { Wire.write(data[i]); } Wire.endTransmission(); } void setup() { Wire.begin(I2C_ADDRESS); // Set the receiver's I2C address Wire.onReceive([](int) { while (Wire.available()) { // Read and discard received data to keep I2C bus buffers clear Wire.read(); } }); if(esp_now_init() != ESP_OK) { Serial.println("Error initializing ESP-NOW"); return; } esp_now_register_recv_cb(onDataReceived); } void loop() { // Any additional logic can be added here }ESP32 Transmitter:
#include <Wire.h> #include <esp_now.h> #define I2C_ADDRESS 8 #define DATA_LENGTH 32 #define DELAY_MS 1000 void onDataReceived(const uint8_t *mac, const uint8_t *data, int len) { // Forward the received data to the I2C bus Wire.beginTransmission(I2C_ADDRESS); for (int i = 0; i < len; i++) { Wire.write(data[i]); } Wire.endTransmission(); } void setup() { Wire.begin(); // Start the transmitter's I2C bus if(esp_now_init() != ESP_OK) { Serial.println("Error initializing ESP-NOW"); return; } esp_now_register_send_cb([](const uint8_t*, esp_now_send_status_t) {}); } void loop() { // Read data from the I2C bus Wire.requestFrom(I2C_ADDRESS, DATA_LENGTH); uint8_t data[DATA_LENGTH]; uint8_t dataLen = 0; while (Wire.available()) { data[dataLen++] = Wire.read(); } // Send the data over ESP-NOW esp_now_send(ESP_NOW_MAC_ADDR_ANY, data, dataLen); delay(DELAY_MS); }Make sure to install the required libraries "Wire" and "esp_now" in the Arduino IDE before uploading the code to the respective ESP32 boards.