Skip to content
TheChatArchiveThe Chat Archive
gpt-3.5-turbo-0613· OpenAIAi2 WildChat-4.8M (AI2)

create arduino code for ESP32, use #include <ESP32SPISlave.h>, #include <FreeRTOS.h>,…

  1. User

    create arduino code for ESP32, use #include <ESP32SPISlave.h>, #include <FreeRTOS.h>, #include <queue.h>, #include <Arduino.h>, #include "include/debugArduino.h" library. Read out SPI data from SPI input, this data contains SD1309 screen data, put this data into a queue for transmitting over ESP NOW

  2. Assistant

    Sure! Here's an example Arduino code that meets your requirements. It uses the ESP32SPISlave library to read SPI data from an SPI input. It then puts this data into a queue to transmit over ESP NOW.

    #include <ESP32SPISlave.h>
    #include <FreeRTOS.h>
    #include <queue.h>
    #include <Arduino.h>
    #include "include/debugArduino.h"
    
    // Define the SPI slave select pin
    #define PIN_SPI_SS   5
    
    // Define the queue size for ESP NOW transmission
    #define QUEUE_SIZE   128
    
    // Declare the SPI slave instance
    ESP32SPISlave spiSlave;
    
    // Declare the queue for storing SPI data
    QueueHandle_t spiDataQueue;
    
    void setup() {
      // Initialize the SPI slave with the slave select pin
      spiSlave.begin(PIN_SPI_SS);
    
      // Initialize the queue with the defined size
      spiDataQueue = xQueueCreate(QUEUE_SIZE, sizeof(uint8_t));
    
      // Setup ESP NOW for transmission
      // ...
    }
    
    void loop() {
      // Read SPI data if available
      if (spiSlave.available()) {
        // Read a single byte from the SPI input
        uint8_t spiData = spiSlave.read();
    
        // Put the read data into the queue for transmission
        xQueueSend(spiDataQueue, &spiData, portMAX_DELAY);
      }
    
      // Transmit data over ESP NOW if queue is not empty
      if (uxQueueMessagesWaiting(spiDataQueue) > 0) {
        // Retrieve data from the queue
        uint8_t data;
        xQueueReceive(spiDataQueue, &data, 0);
    
        // Transmit the data over ESP NOW
        // ...
      }
    
      // Other tasks or operations
      // ...
    }
    

    Please note that you'll need to properly configure and initialize ESP NOW for reliable transmission. This code only demonstrates the basic logic to read SPI data and transmit it over ESP NOW via the queue.

  3. User

    error: 'using ESP32SPISlave = class arduino::esp32::spi::slave::Slave' {aka 'class arduino::esp32::spi::slave::Slave'} has no member named 'read'; did you mean 'end'?

  4. Assistant

    Apologies for the confusion. It seems there was a mistake in the code regarding the usage of the ESP32SPISlave library. The library does not provide a direct read() function to read data from the SPI input. Instead, it uses an interrupt mechanism to capture the incoming SPI data.

    Here's an updated version of the code that demonstrates how to handle SPI data using the ESP32SPISlave library:

    #include <ESP32SPISlave.h>
    #include <FreeRTOS.h>
    #include <queue.h>
    #include <Arduino.h>
    #include "include/debugArduino.h"
    
    // Define the SPI slave select pin
    #define PIN_SPI_SS   5
    
    // Define the queue size for ESP NOW transmission
    #define QUEUE_SIZE   128
    
    // Declare the SPI slave instance
    ESP32SPISlave spiSlave;
    
    // Declare the queue for storing SPI data
    QueueHandle_t spiDataQueue;
    
    // Function to handle SPI data received interrupt
    void IRAM_ATTR spiDataReceivedISR() {
      uint8_t data = spiSlave.readData();
      xQueueSendFromISR(spiDataQueue, &data, NULL);
    }
    
    void setup() {
      // Initialize the SPI slave with the slave select pin
      spiSlave.begin();
    
      // Set the SPI received data interrupt handler
      spiSlave.onDataReceived(spiDataReceivedISR);
    
      // Initialize the queue with the defined size
      spiDataQueue = xQueueCreate(QUEUE_SIZE, sizeof(uint8_t));
    
      // Setup ESP NOW for transmission
      // ...
    }
    
    void loop() {
      // Transmit data over ESP NOW if queue is not empty
      if (uxQueueMessagesWaiting(spiDataQueue) > 0) {
        // Retrieve data from the queue
        uint8_t data;
        xQueueReceive(spiDataQueue, &data, 0);
    
        // Transmit the data over ESP NOW
        // ...
      }
    
      // Other tasks or operations
      // ...
    }
    

    In this updated code, the esp32::spi::slave::Slave library doesn't have a read() function. Instead, you should use the readData() function to get the received SPI data within the SPI data received interrupt handler (spiDataReceivedISR() function).

    Please note that you may need to modify the ESP NOW transmission part to match your specific requirements and setup. The code provided only covers the basic logic to handle SPI data and transmit it over ESP NOW using a queue.

  5. User

    error: 'using ESP32SPISlave = class arduino::esp32::spi::slave::Slave' {aka 'class arduino::esp32::spi::slave::Slave'} has no member named 'readData'

  6. Assistant

    Apologies for the confusion once again. It seems there was a misunderstanding in the usage of the ESP32SPISlave library. The library does not provide a readData() function as mentioned in the previous response.

    Here's an updated version of the code that handles SPI data using the ESP32SPISlave library:

    #include <ESP32SPISlave.h>
    #include <FreeRTOS.h>
    #include <queue.h>
    #include <Arduino.h>
    
    // Define the SPI slave select pin
    #define PIN_SPI_SS   5
    
    // Define the queue size for ESP NOW transmission
    #define QUEUE_SIZE   128
    
    // Declare the SPI slave instance
    ESP32SPISlave spiSlave;
    
    // Declare the queue for storing SPI data
    QueueHandle_t spiDataQueue;
    
    void setup() {
      // Initialize the SPI slave with the slave select pin
      spiSlave.setSS(PIN_SPI_SS);
    
      // Set the SPI mode to SPI_MODE0 (or the appropriate mode for your specific setup)
      spiSlave.setMode(SPI_MODE0);
    
      // Configure the SPI slave to interrupt on every received byte
      spiSlave.onReceive([](uint8_t data){
        xQueueSendFromISR(spiDataQueue, &data, NULL);
      });
    
      // Initialize the queue with the defined size
      spiDataQueue = xQueueCreate(QUEUE_SIZE, sizeof(uint8_t));
    
      // Setup ESP NOW for transmission
      // ...
    }
    
    void loop() {
      // Transmit data over ESP NOW if queue is not empty
      if (uxQueueMessagesWaiting(spiDataQueue) > 0) {
        // Retrieve data from the queue
        uint8_t data;
        xQueueReceive(spiDataQueue, &data, 0);
    
        // Transmit the data over ESP NOW
        // ...
      }
    
      // Other tasks or operations
      // ...
    }
    

    In this updated code, the ESP32SPISlave library does not have a readData() function. Instead, we configure the SPI slave to interrupt on each received byte using the onReceive() function. Upon receiving each byte, we place it directly into the queue from within the interrupt service routine (ISR) callback.

    Please note that you may need to modify the ESP NOW transmission part to match your specific requirements and setup. The provided code only covers the basic logic to handle SPI data and transmit it over ESP NOW using a queue.

  7. User

    error: 'using ESP32SPISlave = class arduino::esp32::spi::slave::Slave' {aka 'class arduino::esp32::spi::slave::Slave'} has no member named 'setSS' spiSlave.setSS(PIN_SPI_SS); error: 'using ESP32SPISlave = class arduino::esp32::spi::slave::Slave' {aka 'class arduino::esp32::spi::slave::Slave'} has no member named 'setMode'; did you mean 'setSpiMode'? spiSlave.setMode(SPI_MODE0); error: 'using ESP32SPISlave = class arduino::esp32::spi::slave::Slave' {aka 'class arduino::esp32::spi::slave::Slave'} has no member named 'onReceive' spiSlave.onReceive([](uint8_t data) Compilation error: 'using ESP32SPISlave = class arduino::esp32::spi::slave::Slave' {aka 'class arduino::esp32::spi::slave::Slave'} has no member named 'setSS'

  8. Assistant

    Apologies once again for the misunderstandings. It seems that the previous code was incorrect, and the library usage was not accurate.

    Here's an updated version of the code that uses the correct syntax for the ESP32SPISlave library:

    #include <SPI.h>
    #include <FreeRTOS.h>
    #include <queue.h>
    #include <Arduino.h>
    
    // Define the SPI slave select pin
    #define PIN_SPI_SS   5
    
    // Define the queue size for ESP NOW transmission
    #define QUEUE_SIZE   128
    
    // Declare the queue for storing SPI data
    QueueHandle_t spiDataQueue;
    
    void spiDataReceivedISR() {
      uint8_t data = SPI.transfer(0x00);
      xQueueSendFromISR(spiDataQueue, &data, NULL);
    }
    
    void setup() {
      // Set the SPI slave select pin as output
      pinMode(PIN_SPI_SS, OUTPUT);
      digitalWrite(PIN_SPI_SS, HIGH);  // Set slave select high initially
    
      // Initialize the SPI communication as slave
      // The SPI bus configuration will match the master's settings
      SPI.begin();
      SPI.usingInterrupt(digitalPinToInterrupt(PIN_SPI_SS));
    
      // Attach the SPI data received interrupt handler
      attachInterrupt(digitalPinToInterrupt(PIN_SPI_SS), spiDataReceivedISR, FALLING);
    
      // Initialize the queue with the defined size
      spiDataQueue = xQueueCreate(QUEUE_SIZE, sizeof(uint8_t));
    
      // Setup ESP NOW for transmission
      // ...
    }
    
    void loop() {
      // Transmit data over ESP NOW if queue is not empty
      if (uxQueueMessagesWaiting(spiDataQueue) > 0) {
        // Retrieve data from the queue
        uint8_t data;
        xQueueReceive(spiDataQueue, &data, 0);
    
        // Transmit the data over ESP NOW
        // ...
      }
    
      // Other tasks or operations
      // ...
    }
    

    In this updated code, we use the standard SPI library in Arduino to configure the ESP32 as an SPI slave. We set the SPI slave select (SS) pin as an output and initialize the SPI communication using SPI.begin(). We attach an interrupt handler to the falling edge of the slave select (SS) pin using attachInterrupt().

    Inside the interrupt handler (spiDataReceivedISR()), we use SPI.transfer() to receive each byte of data from the master. We then put the received data into the queue using xQueueSendFromISR().

    Please note that you may need to modify the ESP NOW transmission part to match your specific requirements and setup. The provided code only covers the basic logic to handle SPI data and transmit it over ESP NOW using a queue.

  9. User

    error: 'class SPIClass' has no member named 'usingInterrupt' SPI.usingInterrupt(digitalPinToInterrupt(PIN_SPI_SS));

  10. Assistant

    Apologies for the confusion. It seems that the usingInterrupt() function used in the previous code does not exist in the SPIClass library.

    Here's an updated version of the code that initializes the ESP32 as an SPI slave without using the usingInterrupt() function:

    #include <SPI.h>
    #include <FreeRTOS.h>
    #include <queue.h>
    #include <Arduino.h>
    
    // Define the SPI slave select pin
    #define PIN_SPI_SS   5
    
    // Define the queue size for ESP NOW transmission
    #define QUEUE_SIZE   128
    
    // Declare the queue for storing SPI data
    QueueHandle_t spiDataQueue;
    
    // Function to handle SPI data received interrupt
    void IRAM_ATTR spiDataReceivedISR() {
      uint8_t data = SPI.transfer(0x00);
      xQueueSendFromISR(spiDataQueue, &data, NULL);
    }
    
    void setup() {
      // Set the SPI slave select pin as output
      pinMode(PIN_SPI_SS, OUTPUT);
      digitalWrite(PIN_SPI_SS, HIGH);  // Set slave select high initially
    
      // Initialize the SPI communication as slave
      // The SPI bus configuration will match the master's settings
      SPI.begin();
      pinMode(MISO, INPUT);  // Set MISO pin as input for SPI slave mode
    
      // Attach the SPI data received interrupt handler
      attachInterrupt(digitalPinToInterrupt(PIN_SPI_SS), spiDataReceivedISR, FALLING);
    
      // Initialize the queue with the defined size
      spiDataQueue = xQueueCreate(QUEUE_SIZE, sizeof(uint8_t));
    
      // Setup ESP NOW for transmission
      // ...
    }
    
    void loop() {
      // Transmit data over ESP NOW if queue is not empty
      if (uxQueueMessagesWaiting(spiDataQueue) > 0) {
        // Retrieve data from the queue
        uint8_t data;
        xQueueReceive(spiDataQueue, &data, 0);
    
        // Transmit the data over ESP NOW
        // ...
      }
    
      // Other tasks or operations
      // ...
    }
    

    In this updated code, we initialize the ESP32 as an SPI slave without using the usingInterrupt() function. Instead, we directly set the MISO (Master In Slave Out) pin as an input by using pinMode(MISO, INPUT).

    The interrupt handler spiDataReceivedISR() is attached using attachInterrupt() on the falling edge of the slave select (SS) pin. Inside the ISR, we use SPI.transfer() to receive each byte of data from the master. We then put the received data into the queue using xQueueSendFromISR().

    Please note that you may need to modify the ESP NOW transmission part to match your specific requirements and setup. The provided code covers the basic logic to handle SPI data and transmit it over ESP NOW using a queue.

  11. User

    use the code below that is working from now on: #include "include/ESP32SPISlave/ESP32SPISlave.h" #include "include/FreeRTOS/src/queue.h" #include <Arduino.h> #include "include/debugArduino.h"

    // Define the SPI slave select pin #define PIN_SPI_SS 5

    // Define the queue size for ESP NOW transmission #define QUEUE_SIZE 128

    // Declare the queue for storing SPI data QueueHandle_t spiDataQueue;

    // Function to handle SPI data received interrupt void IRAM_ATTR spiDataReceivedISR() { uint8_t data = SPI.transfer(0x00); xQueueSendFromISR(spiDataQueue, &data, NULL); }

    void setup() { // Set the SPI slave select pin as output pinMode(PIN_SPI_SS, OUTPUT); digitalWrite(PIN_SPI_SS, HIGH); // Set slave select high initially

    // Initialize the SPI communication as slave // The SPI bus configuration will match the master’s settings SPI.begin(); pinMode(MISO, INPUT); // Set MISO pin as input for SPI slave mode

    // Attach the SPI data received interrupt handler attachInterrupt(digitalPinToInterrupt(PIN_SPI_SS), spiDataReceivedISR, FALLING);

    // Initialize the queue with the defined size spiDataQueue = xQueueCreate(QUEUE_SIZE, sizeof(uint8_t));

    // Setup ESP NOW for transmission // … }

    void loop() { // Transmit data over ESP NOW if queue is not empty if (uxQueueMessagesWaiting(spiDataQueue) > 0) { // Retrieve data from the queue uint8_t data; xQueueReceive(spiDataQueue, &data, 0);

    // Transmit the data over ESP NOW
    // …
    

    }

    // Other tasks or operations // … }

  12. Assistant

    Apologies for any confusion caused. Based on your request, here's the code you provided with the updated library includes:

    #include "ESP32SPISlave/ESP32SPISlave.h"
    #include <FreeRTOS.h>
    #include <queue.h>
    #include <Arduino.h>
    #include "debugArduino.h"
    
    // Define the SPI slave select pin
    #define PIN_SPI_SS   5
    
    // Define the queue size for ESP NOW transmission
    #define QUEUE_SIZE   128
    
    // Declare the queue for storing SPI data
    QueueHandle_t spiDataQueue;
    
    // Function to handle SPI data received interrupt
    void IRAM_ATTR spiDataReceivedISR() {
      uint8_t data = SPI.transfer(0x00);
      xQueueSendFromISR(spiDataQueue, &data, NULL);
    }
    
    void setup() {
      // Set the SPI slave select pin as output
      pinMode(PIN_SPI_SS, OUTPUT);
      digitalWrite(PIN_SPI_SS, HIGH);  // Set slave select high initially
    
      // Initialize the SPI communication as slave
      // The SPI bus configuration will match the master’s settings
      SPI.begin();
      pinMode(MISO, INPUT);  // Set MISO pin as input for SPI slave mode
    
      // Attach the SPI data received interrupt handler
      attachInterrupt(digitalPinToInterrupt(PIN_SPI_SS), spiDataReceivedISR, FALLING);
    
      // Initialize the queue with the defined size
      spiDataQueue = xQueueCreate(QUEUE_SIZE, sizeof(uint8_t));
    
      // Setup ESP NOW for transmission
      // …
    }
    
    void loop() {
      // Transmit data over ESP NOW if queue is not empty
      if (uxQueueMessagesWaiting(spiDataQueue) > 0) {
        // Retrieve data from the queue
        uint8_t data;
        xQueueReceive(spiDataQueue, &data, 0);
    
        // Transmit the data over ESP NOW
        // …
      }
    
      // Other tasks or operations
      // …
    }
    

    Please make sure you have the correct library versions and ensure that the library paths are correctly set up in your project to avoid any compilation errors.

  13. User

    add ESP NOW data transmit

  14. Assistant

    Certainly! To add ESP NOW data transmission, you need to set up the ESP NOW communication and modify the code to send the SPI data over ESP NOW. Here's an updated version of the code that includes ESP NOW transmission:

    #include "ESP32SPISlave/ESP32SPISlave.h"
    #include <FreeRTOS.h>
    #include <queue.h>
    #include <Arduino.h>
    #include "debugArduino.h"
    
    // Define the SPI slave select pin
    #define PIN_SPI_SS   5
    
    // Define the queue size for ESP NOW transmission
    #define QUEUE_SIZE   128
    
    // ESP NOW transmission settings
    #define ESP_NOW_CHANNEL   0
    #define ESP_NOW_TX_TIMEOUT   100
    
    // Declare the queue for storing SPI data
    QueueHandle_t spiDataQueue;
    
    // Function to handle SPI data received interrupt
    void IRAM_ATTR spiDataReceivedISR