Skip to content
TheChatArchiveThe Chat Archive
gpt-3.5-turbo-0613· OpenAIAi2 WildChat-4.8M (AI2)

In following scrip I made a mistake the chipset is not WS2811 but WS2812 does this…

  1. User

    In following scrip I made a mistake the chipset is not WS2811 but WS2812 does this change the script exept of define CHIPSET WS2812 instead of WS2811. #include <FastLED.h>

    #define LED_PIN 6 #define COLOR_ORDER GRB #define CHIPSET WS2811 #define NUM_LEDS 30

    #define BRIGHTNESS 100 #define FRAMES_PER_SECOND 60

    CRGB leds[NUM_LEDS];

    CRGBPalette16 gPal;

    // Futaba RC Receiver variables #define RC_PIN A0 #define RC_MIN 1000 #define RC_MAX 2000 #define RC_MID 1500 #define RC_DEADZONE 100

    int currentPalette = 0; int prevRCValue = RC_MID;

    void setup() { delay(3000); // sanity delay FastLED.addLeds<CHIPSET, LED_PIN, COLOR_ORDER>(leds, NUM_LEDS).setCorrection( TypicalLEDStrip ); FastLED.setBrightness( BRIGHTNESS );

    // This first palette is the basic ‘black body radiation’ colors, // which run from black to red to bright yellow to white. // gPal = HeatColors_p;

    // These are other ways to set up the color palette for the ‘fire’. // First, a gradient from black to red to yellow to white – similar to HeatColors_p // (GPAL A) // gPal = CRGBPalette16( CRGB::Black, CRGB::Red, CRGB::Yellow, CRGB::White);

    // Second, this palette is like the heat colors, but blue/aqua instead of red/yellow // (GPAL B) // gPal = CRGBPalette16( CRGB::Black, CRGB::Blue, CRGB::Aqua, CRGB::White);

    // Third, here’s a simpler, three-step gradient, from black to red to white // (GPAL C) gPal = CRGBPalette16( CRGB::Black, CRGB::Green, CRGB::Yellow); }

    void loop() { // Read RC receiver value int rcValue = pulseIn(RC_PIN, HIGH, 25000); rcValue = constrain(rcValue, RC_MIN, RC_MAX);

    // Check if RC receiver value is within the deadzone if (abs(rcValue - RC_MID) < RC_DEADZONE) { rcValue = RC_MID; }

    // Toggle color mode based on RC receiver value if (rcValue < RC_MID && prevRCValue >= RC_MID) { currentPalette--; if (currentPalette < 0) { currentPalette = 2; } } else if (rcValue >= RC_MID && prevRCValue < RC_MID) { currentPalette++; if (currentPalette > 2) { currentPalette = 0; } }

    prevRCValue = rcValue;

    // Add entropy to random number generator; we use a lot of it. random16_add_entropy( random());

    // Update palette based on currentPalette variable switch (currentPalette) { case 0: gPal = CRGBPalette16( CRGB::Red, CRGB::Red, CRGB::Yellow, CRGB::White); break; case 1: gPal = CRGBPalette16( CRGB::Aqua, CRGB::Blue, CRGB::Aqua, CRGB::White); break; case 2: gPal = CRGBPalette16( CRGB::Green, CRGB::Green, CRGB::Yellow); break; }

    Fire2012WithPalette(); // run simulation frame, using palette colors

    FastLED.show(); // display this frame FastLED.delay(1000 / FRAMES_PER_SECOND); }

    #define COOLING 55 #define SPARKING 120 #define FALLING 50

    //********************************************************************************************// // PLAY WITH FALLING, COOLING AND SPARKLING

    void Fire2012WithPalette() { // Array of temperature readings at each simulation cell static uint8_t heat[NUM_LEDS];

    // Step 1. Cool down every cell a little for( int i = 0; i < NUM_LEDS; i++) { heat[i] = qsub8( heat[i], random8(0, ((COOLING * 10) / NUM_LEDS) + 2)); }

    // Step 2. Heat from each cell drifts ‘up’ and diffuses a little for(int k = NUM_LEDS - 1; k >= 2; k--) { heat[k] = (heat[k - 1] + heat[k - 2] + heat[k - 2] ) / 3; }

    // Step 3. Randomly ignite new ‘sparks’ of heat near the bottom if( random8() < FALLING ) { int y = random8(7); heat[y] = qadd8( heat[y], random8(160,255) ); }

    // Step 4. Map from heat cells to LED colors for( int j = 0; j < NUM_LEDS; j++) { // Scale the heat value from 0-255 down to 0-240 // for best results with color palettes. uint8_t colorindex = scale8( heat[j], 240); CRGB color = ColorFromPalette( gPal, colorindex); leds[j] = color; } }

  2. Assistant

    The only change you need to make is to replace "WS2811" with "WS2812" in the line "#define CHIPSET WS2811". It should be "#define CHIPSET WS2812".