Polish and modify: 1. Grind freeze-dried leaf samples into fine powder in a motor and…
- User
Polish and modify: 1. Grind freeze-dried leaf samples into fine powder in a motor and pestle 2. Transfer the powder (~20-30 mg) into microcentrifuge tubes 3. Fill the tube with 1.3 mL of ice-cold 10% TCA/acetone 4. Mix well by vortexing 5. Centrifuge at 12,000 x g for 15 min, remove the supernatant and place in ice. 6. Fill the tubes with 1.3 mL 80% methanol and 0.1 M ammonium acetate 7. Mix well by vortexing 8. Centrifuge at 12,000 x g for 15 min, remove the supernatant and place in ice. 9. Fill the tubes with 1.3mL 80% acetone and vortex until the pellet is filly dispersed 10. Centrifuge at 12,000 x g for 15 min, remove the supernatant and place in ice. 11. Air dry tubes at room temperature 12. Add ~0.1 to 0.2 mg of material to 1 mL of 1:1 phenol/SDS buffer (30% sucrose, 2% SDS, 0.1 M Tris-HCl, pH 8.0, 5% 2-mercaptoethanol) 13. Mix thoroughly and incubate for 20 minutes in ice 14. Centrifuge at 12,000 x g for 15 min, remove the supernatant and place in ice. 15. Transfer the upper phenol phase (400 µL) to a clean tube and fill the tube with methanol containing 0.1 M ammonium acetate and store at 4°C overnight. 16. Centrifuge at 12,000 x g for 15 min, remove the supernatant and place in ice. A white pellet should appear. If no phase separation occurs, add more phenol 100 µL to the mixture, mix well and centrifuge again. 17. Wash the pellet once with 80% methanol and 80% acetone and centrifuge as above. Allow proteins to air dry and 18. Dissolve the pellets in 200 µL of SDS sample buffer and analyze protein concentrations
- Assistant
- Grind freeze-dried leaf samples into a fine powder using a mortar and pestle.
- Transfer approximately 20-30 mg of the powder into microcentrifuge tubes.
- Add 1.3 mL of ice-cold 10% TCA/acetone to each tube.
- Mix the contents of the tubes thoroughly by vortexing.
- Centrifuge the tubes at 12,000 x g for 15 minutes. Carefully remove the supernatant and place it on ice.
- Fill the tubes with 1.3 mL of 80% methanol and 0.1 M ammonium acetate.
- Mix the contents of the tubes thoroughly by vortexing.
- Centrifuge the tubes at 12,000 x g for 15 minutes. Carefully remove the supernatant and place it on ice.
- Fill the tubes with 1.3 mL of 80% acetone and vortex until the pellet is fully dispersed.
- Centrifuge the tubes at 12,000 x g for 15 minutes. Carefully remove the supernatant and place it on ice.
- Allow the tubes to air dry at room temperature.
- Add approximately 0.1 to 0.2 mg of the material to 1 mL of a 1:1 phenol/SDS buffer (consisting of 30% sucrose, 2% SDS, 0.1 M Tris-HCl, pH 8.0, and 5% 2-mercaptoethanol).
- Mix the contents thoroughly and incubate for 20 minutes on ice.
- Centrifuge the tubes at 12,000 x g for 15 minutes. Carefully remove the supernatant and place it on ice.
- Transfer 400 µL of the upper phenol phase to a clean tube and fill the tube with methanol containing 0.1 M ammonium acetate. Store the tube at 4°C overnight.
- Centrifuge the tube at 12,000 x g for 15 minutes. Carefully remove the supernatant and place it on ice. A white pellet should be visible. If there is no phase separation, add an additional 100 µL of phenol to the mixture, mix well, and centrifuge again.
- Wash the pellet once with 80% methanol and once with 80% acetone. Centrifuge as mentioned above. Allow the proteins to air dry.
- Dissolve the pellets in 200 µL of SDS sample buffer and analyze protein concentrations.
- User
RIPA buffer composition
- Assistant
RIPA buffer is a commonly used lysis buffer for protein extraction from cells or tissues. The composition of RIPA buffer typically includes the following components:
- 50 mM Tris-HCl (pH 7.4): Tris-HCl acts as a buffering agent to maintain a stable pH.
- 150 mM NaCl: Sodium chloride helps maintain the osmotic balance and solubility of proteins.
- 1% NP-40 (Nonidet P-40 or Triton X-100): Nonionic detergents like NP-40 solubilize and disrupt cell membranes, allowing release of proteins.
- 0.5% sodium deoxycholate: Sodium deoxycholate is an anionic detergent that helps to solubilize membrane proteins and disrupt lipid-protein interactions.
- 0.1% SDS (sodium dodecyl sulfate): SDS is an anionic detergent that denatures proteins and helps to solubilize hydrophobic molecules.
- Protease inhibitors: Protease inhibitors, such as phenylmethylsulfonyl fluoride (PMSF), aprotinin, leupeptin, and pepstatin, are commonly added to RIPA buffer to prevent protein degradation by endogenous proteases.
- Phosphatase inhibitors: Phosphatase inhibitors like sodium orthovanadate or sodium fluoride are often included in RIPA buffer to inhibit phosphatase activity and prevent dephosphorylation of proteins of interest.
- Optional additives: Depending on the specific experimental requirements, RIPA buffer may also contain additional components like EDTA (to chelate divalent metal ions and inhibit metal-dependent proteases) or glycerol (to stabilize proteins during storage).
It is important to note that the exact concentrations of each component may vary based on the specific protocol or application.