Skip to content
The Chat Archive
gpt-3.5-turbo-0613· OpenAI WildChat-4.8M (AI2)

翻译 玻璃的光谱发射率

  1. User

    翻译 玻璃的光谱发射率

  2. Assistant

    The spectral emissivity of glass.

  3. User

    翻译 90 Transmissivity of Glass Introduction In this project we investigate the radiative properties of two particular types of glass: one of them a standard glass and the other what is called a “low – E” (for emissivity) glass. Stop by any glass shop and you can pick up literature on various brands of the latter. You will find that many modern windows are made of two panes of glass, at least one of them having a low-E coating, and with, perhaps, an inert gas like argon or krypton sealed in the gap between them. In such glass manufactured for residential applications, the special coating is usually not visible to the eye. They are often visible on the windows of office buildings. Some coatings are metallic and may interfere with cell phone reception within a building. Polyester films don’t interfere with your cell phone. A data file of the spectral transmissivity ( λ τ ) is supplied for two representative glasses, and we will determine the total transmissivity of each glass for both solar (short) and terrestrial (long) wavelength radiation. Recall that unlike total emissivity, which is a function of the temperature of the radiating surface itself, the total transmissivity (as well as total absorptivity and reflectivity) are functions of the irradiation. That is, the integration of the spectral value to get the total (or average) value must be weighted using the spectrum corresponding to the source of the radiation. Here we will take the sources to be blackbodies having two particular temperatures, specifically that of the sun and another corresponding to everyday terrestrial temperatures. We will do the integration roughly using the conventional, tabulated blackbody radiation functions and then follow up with a more accurate numerical integration using Simpson’s 1/3 rule. For both glasses you will compute quite different values of total transmissivity depending on whether the incoming radiation is high temperature solar (mostly short wavelength) or low temperature terrestrial (long wavelength) in origin. This significant difference in transmissivity to short vs. long wavelength radiation leads to what is known as the “greenhouse effect,” a term which more recently has been extended to the analogous effect in the atmosphere caused by the accumulation of CO2, water vapor and other so-called “greenhouse” gases. Learning Objectives By the time you have completed this assignment, you will be able to:

    1. Use terms like short wavelength radiation, visible radiation, long wavelength radiation, heat, low-emissivity glass, etc., intelligently,
    2. Explain how a total property is determined from a spectral property and why weighting by the appropriate function is needed in the integration,
    3. Use the tabulated blackbody radiation functions,
    4. Apply Simpson’s rule to the integration of any particular function,
    5. Explain how low-E glass may be used to achieve desired energy conservation goals. 8.1 Transmissivity of Glass Transmissivity of Glass Heat Transfer Today 2 The Problem Data for the transmissivity of two glasses, one standard (uncoated) and the other lowemissivity, as a function of wavelength is given in the second sheet of the Planck’s Law workbook. That data is plotted below. Both regular and low-E glass have high transmissivity (τ = 0.8 - 0.9) in the visible portion of the spectrum ( λ ≈ 0.4 - 0.7μm). The transmissivity of the low-E glass is seen to drop off much faster than that of ordinary glass in the near infrared region. That means that with low-E glass the inside of the house still receives the visible sun light but with less overall solar heat gain. It is not obvious where the term “low-E” comes from, but sinceα +ρ + τ=1, low transmissivity and high reflectivity imply low absorptivity, which means low emissivity, sinceαλ λ =ε . “Low-E” thus refers strictly to the behavior of the glass in the infrared (long wavelength) part of the spectrum. If one were doing a radiative heat transfer analysis for the interior of a room (as discussed in the next chapter), the window would be considered an opaque surface with surface resistance = i i i ρ A ε . Then high reflectivity and low emissivity implies a high resistance to radiative heat transfer. High surface radiative resistance means less heat loss from the interior of the house during the heating season. In your calculations assume the sun is a blackbody source at 5800K and produces an irradiation of 1100 W/m2 on the glass - which might be the windshield of your car. (This value of the irradiation (G) includes the effect of attenuation in the earth’s atmosphere, which reduces it from the value of the solar constant (1353 W/m2 ). The solar constant corresponds to that which arrives per square meter normal to the sun’s rays at the orbital radius of the earth from a blackbody source having the diameter of the sun and at the sun’s apparent temperature. The terrestrial source is assumed to be black and at 300K. You are to do the following and comment on your findings: Transmissivity of Glass 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1 0 0.2 0.4 0.6 0.8 1 1.2 Wavelength (micrometers) Regular Glass Low "E" Glass Violet Red Figure1. Spectral transmissivity of regular and “Low E” glass 8.1 Transmissivity of Glass Transmissivity of Glass Heat Transfer Today 3
    6. Access the Planck’s Law workbook. The second worksheet includes a table of the transmissivity data for both glasses as seen in graphical form above.
    7. Approximate both transmissivities as constant over a particular wavelength interval (make a good “eyeball” estimate based on the plots) and 0.0 outside that range, i.e., as a “boxcar” function. Sketch your function for both types of glass in your notes.
    8. Using either the blackbody radiation function table in the text or the integration function of the Planck’s law workbook with the boxcar functions you have chosen, estimate the total transmissivity of both glasses to irradiation from the sun. Assume the sun is a blackbody at 5800K. (See Equation 1 in the Appendix.) With the boxcar function approximation you can break the spectrum 0≤ λ ≤ ∞ into three segments: 0 1 ≤ ≤λ λ where τ and thus the integral are zero; a second interval in which τ is a constant and can be brought outside the integral and a third section 2 λ λ ≤ ≤ ∞ where τ and thus the integral are again zero.
    9. Do this calculation again to estimate the total transmissivity of both glasses to the irradiation from a terrestrial source. Assume a blackbody at 300K. A table for recording your results is given below.
    10. Now use Simpson’s 1/3 Rule as described in the Appendix to do a numerical integration. Since you will be using the exact values from the tabulated data rather than the boxcar function you used earlier, your Simpson rule results should give better estimates. Now you should now have eight total transmissivities: Regular Glass Regular Glass “Low E” Glass “Low E” Glass B.B.Rad. Func. Simpson’s Rule B.B.Rad. Func. Simpson’s Rule Solar Radiation (5800K)

    Terrestrial Radiation (300K) Computed Transmissivities 6 Using the transmissivity values found in Step 5 (which are presumably more accurate than those found in Step 3), find the total solar energy (W/m2 ) transmitted through both glasses. Use the value of G = 1100 W/m2 given above for solar irradiation. 7. Again using your values from Step 5, find the total energy transmitted from the terrestrial source (blackbody at 300K) for both glasses (W/m2 ). Assume the source and the glass are two closely spaced parallel plates. Regular Glass “Low E" Solar Radiation Terrestrial Radiation Transmitted Radiation (W/m2 ) 8.1 Transmissivity of Glass Transmissivity of Glass Heat Transfer Today 4 8. Speculate on how you might profitably incorporate low-E glass into the design of a home. Consider both summer and winter scenarios and northern and southern climates. Include sketches.

    References

    1. 2001 ASHRAE Handbook - Fundamentals, American Society of Heating, Refrigerating and Air-Conditioning Engineers, Inc. Atlanta (2001).

    Note: Some sources, including the ASHRAE Handbook, make a distinction between the “ivity” ending used here, and the “ance” ending. Technically the transmissivity, reflectivity, etc. refer to inherent properties of a bulk sample of the material, while the “ance,” e.g., transmittance, refers to the property of a specific sample or thickness of a substance or combination of substances. 2. Çengel, Y.A., Heat and Mass Transfer – A Practical Approach, 3rd Ed., McGraw-Hill, 2007, pp. 679-688. 3. Chapra, S.C., and Canale, R.P., Numerical Methods for Engineers, 2nd Ed., McGraw-Hill, New York (1988), pp 490-494. Appendix - The Numerical Integration Problems like that given here are discussed in all heat transfer textbooks, but in those problems the variation of the transmissivity with wavelength is taken to be a very simple boxcar function - e.g., a constant over a particular wavelength range and identically 0.0 or another constant over the rest of the spectrum. Evaluating total properties can then be done easily using the blackbody radiation function table in the text or the integrate function in the Planck’s Law workbook. In order to force you to do a numerical integral of the following definition of the total transmissivity: λ λ 0 λ 0 τ (λ )G (λ)dλ τ= G (λ)dλ ∞ ∞ ∫ ∫ (1) we have given you more detailed transmissivity data at a large number of equally spaced points. Assume zero transmissivity outside the range of the given data. Since the irradiation is assumed to come from a blackbody source, then the weighting function, 2 1 λ λ,B C 5 λT C G (λ ) = E (λ,T) = λ e -1 ⎡ ⎤ ⎢ ⎥ ⎣ ⎦ (2) Here C1 = 3.742x108 W 4 2 ⋅μm /m and C2 = 1.439x104 μm K⋅ . The Planck’s Law workbook has a VBA function already prepared for this expression and you can use it in your calculations exactly as if it were a supplied function like the sine or cosine. 8.1 Transmissivity of Glass Transmissivity of Glass Heat Transfer Today 5

    You can use Simpson’s 1/3 rule for the integration: b 0 1 2 3 4 n-2 n-1 n a h f(x)dx y +4y +2y +4 y +2y +...+2y +4 y +y 3 ≈ ⎡ ⎤ ∫ ⎣ ⎦ (3)

    Here y0, y1 … yn are the ordinates of the curve y = f (x). (Here in the numerator of Equation 1 f(x) is the product λ λ,B τ (λ )E (λ,T) ) at the x values x0 =a, x1 = a + h, ... xn = a + nh = b. You may recall that the Trapezoidal Rule for numerical integration assumes a linear function between each pair of points. Simpson’s 1/3 rule assumes a quadratic relation for each trio of adjacent points; that is where the sequence 1,4,2,4,… comes from. Alternatively Simpson’s 1/3 rule may be written: n-1 n-2 b o i jn i=1,3,5 j=2,4,6 a f(x )+4 f(x )+2 f(x )+f(x ) f(x)dx (b-a) 3n ≈ ∑ ∑ ∫ (4)

    For the given data file n = 80, i.e., there are 81 data points. (You need an even number of intervals in order to use Simpson’s 1/3 Rule.) Note that the integral in the denominator of Equation 1 above should equal 4 σT . This suggests a way to check your implementation of Simpson’s Rule (realizing that you do have to cut it off somewhere short of infinity) using the table of blackbody radiation functions given in the text.

  4. Assistant

    玻璃的透过率 介绍 在这个项目中,我们研究了两种特定类型的玻璃的辐射特性:其中一种是标准玻璃,另一种是所谓的“低E”(代表发射率)玻璃。在任何玻璃商店,你可以拿到关于后者不同品牌的文献资料。你会发现现代许多窗户都是由两层玻璃制成的,至少其中一层具有低E涂层,并且在它们之间的间隙中封入像氩气或氪气这样的惰性气体。在用于住宅应用的此类玻璃中,特殊涂层通常对肉眼不可见。它们通常在办公楼的窗户上是可见的。一些涂层是金属的,并可能干扰建筑物内的手机信号接收。聚酯薄膜不会干扰你的手机信号。提供了两种代表性玻璃的光谱透过率(λτ)的数据文件,我们将确定每种玻璃在太阳(短波长)和地球(长波长)辐射下的总透过率。

    请注意,与总发射率不同,总透过率(以及总吸收率和反射率)是辐射照射的函数。也就是说,为了得到总值(或平均值),必须使用与辐射源相对应的光谱来加权积分。在这里,我们将源视为具有两个特定温度的黑体,具体而言是太阳的温度和与日常地球温度相对应的另一个温度。我们将使用传统的、表格化的黑体辐射函数进行粗略积分,然后再使用较准确的数值积分方法,如辛普森1/3规则。

    对于两种玻璃,你将根据入射辐射是否来自高温太阳(主要是短波长)或低温地球(长波长),计算出相当不同的总透过率。对于短波长和长波长辐射的透过率显著差异导致了所谓的“温室效应”,这个术语最近也推广到由CO2、水蒸气和其他所谓的“温室”气体积累在大气中引起的类似效应。

    学习目标 完成此任务后,您将能够:

    1. 聪明地使用如短波长辐射、可见辐射、长波长辐射、热、低发射率玻璃等术语。
    2. 解释如何根据光谱性能确定总性能,以及为什么需要使用适当的函数对积分进行加权。
    3. 使用文本中的表格化黑体辐射函数。
    4. 应用辛普森1/3规则对任何特定函数进行积分。
    5. 解释如何使用低E玻璃来实现所期望的节能目标。
  5. User

    可见光波段

  6. Assistant

    Visible light wavelength

  7. User

    可见光波段范围是多少、

  8. Assistant

    可见光波段的波长范围是从大约380纳米到750纳米。这个范围对应的颜色从紫色(较短波长)到红色(较长波长)。其中,紫光波长最短,约为380至450纳米;蓝光波长为450至495纳米;绿光波长为495至570纳米;黄光波长为570至590纳米;橙光波长为590至620纳米;红光波长最长,为