Skip to content
TheChatArchiveThe Chat Archive
gpt-3.5-turbo-0613· OpenAIAi2 WildChat-4.8M (AI2)

dsp28335 PMSM FOC code

  1. User

    dsp28335 PMSM FOC code

  2. Assistant

    Here's an example code for PMSM (Permanent Magnet Synchronous Motor) Field-Oriented Control (FOC) using the TMS320F28335 digital signal processor (DSP):

    #include "F28335_sci_io.h"
    #include "F28335_examples.h"
    
    #define PWM_FREQ 20000       // PWM frequency in Hz
    #define PERIOD ((float)1/PWM_FREQ)   // PWM period in seconds
    #define BASE_FREQ 50         // Base frequency in Hz
    #define NUM_POLE_PAIRS 2     // Number of pole pairs
    #define KP 0.5               // Proportional gain
    #define KI 0.001             // Integral gain
    #define MAX_DUTY 0.95        // Maximum duty cycle
    
    float target_speed;          // Target motor speed in Hz
    float measured_speed;        // Measured motor speed in Hz
    float error;                 // Speed error
    float integral;              // Integral term for the controller
    float duty_cycle;            // Duty cycle for the PWM
    
    void main(void)
    {
        InitSystem();            // Initialize system peripherals
        InitPWM();               // Initialize PWM module
        InitADC();               // Initialize ADC module
        InitSCI();               // Initialize SCI module
    
        while(1)
        {
            // Read target speed from SCI input
            while(!SciaRegs.SCIFFRX.bit.RXFFST);   // Wait until at least one byte is in FIFO
            target_speed = (float)SciaRegs.SCIRXBUF.all;
    
            // Measure motor speed using ADC
            measured_speed = ADC_Result * BASE_FREQ / (ADC_RESOLUTION * NUM_POLE_PAIRS);
    
            // Calculate speed error
            error = target_speed - measured_speed;
    
            // Update the integral term
            integral += error * PERIOD;
    
            // Calculate duty cycle
            duty_cycle = KP * error + KI * integral;
    
            // Limit duty cycle to the maximum allowed value
            duty_cycle = (duty_cycle > MAX_DUTY) ? MAX_DUTY : duty_cycle;
    
            // Update PWM duty cycle
            EPwm1Regs.CMPA.half.CMPA = (Uint16)(duty_cycle * EPWM1_TIMER_PERIOD);
    
            // Send measured speed to SCI output
            while(!SciaRegs.SCIFFTX.bit.TXFFST);   // Wait until at least one empty location is in FIFO
            SciaRegs.SCITXBUF = (Uint16)measured_speed;
        }
    }
    
    void InitSystem(void)
    {
        // Disable watchdog timer
        DisableDog();
    
        // Initialize system clock (200 MHz)
        InitSysCtrl();
    
        // Initialize PIE control registers to their default state
        InitPieCtrl();
    
        // Disable interrupts
        DINT;
    
        // Clear all PIE interrupts and initialize PIE vector table
        IER = 0x0000;
        IFR = 0x0000;
        InitPieVectTable();
    
        // Enable global interrupts
        EINT;
        ERTM;
    }
    
    void InitPWM(void)
    {
        // Enable PWM1 clock
        CpuSysRegs.PCLKCR2.bit.EPWM1 = 1;
    
        // Reset PWM1 module
        EPwm1Regs.TBCTL.bit.SWFSYNC = 1;
    
        // Set PWM1 frequency, period and duty cycle
        EPwm1Regs.TBPRD = (Uint16)(EPWM1_TIMER_PERIOD - 1);   // Set period
        EPwm1Regs.CMPA.half.CMPA = 0;                         // Set initial duty cycle
        EPwm1Regs.TBCTL.bit.CTRMODE = TB_COUNT_UPDOWN;         // Count up/down
        EPwm1Regs.TBCTL.bit.PHSEN = TB_DISABLE;                // Disable phase loading
        EPwm1Regs.TBCTL.bit.PHSDIR = TB_DOWN;                  // Count down after period
        EPwm1Regs.TBCTL.bit.HSPCLKDIV = TB_DIV1;               // High-speed time base clock prescaler
        EPwm1Regs.AQCTLA.bit.CAU = AQ_SET;                     // PWM1A high when counted value reaches CMPA
        EPwm1Regs.AQCTLA.bit.CAD = AQ_CLEAR;                   // PWM1A low when counted value reaches CMPA
        EPwm1Regs.AQCTLB.bit.CBU = AQ_CLEAR;                   // PWM1B low when counted value reaches CMPA
        EPwm1Regs.AQCTLB.bit.CBD = AQ_SET;                     // PWM1B high when counted value reaches CMPA
    
        // Start PWM1 module
        EPwm1Regs.TBCTL.bit.SWFSYNC = 0;
    }
    
    void InitADC(void)
    {
        // Enable ADC clock
        CpuSysRegs.PCLKCR0.bit.ADCENCLK = 1;
    
        // Reset ADC module
        AdcRegs.ADCTRL2.bit.SOCSEQ1 = 0;
        AdcRegs.ADCTRL2.bit.SOCSEQ2 = 0;
        AdcRegs.ADCTRL2.bit.SOCSEQ3 = 0;
        AdcRegs.ADCTRL2.bit.SOCSEQ4 = 0;
        AdcRegs.ADCTRL2.bit.RST_SEQ1 = 1;
        AdcRegs.ADCTRL2.bit.RST_SEQ2 = 1;
        AdcRegs.ADCTRL2.bit.RST_SEQ3 = 1;
        AdcRegs.ADCTRL2.bit.RST_SEQ4 = 1;
    
        // Configure ADC module
        AdcRegs.ADCTRL1.bit.CONT_RUN = 0;         // Stop ADC conversions
        AdcRegs.ADCTRL1.bit.SEQ_CASC = 0;         // Disable cascaded sequencer mode
        AdcRegs.ADCTRL1.bit.ACQ_PS = 7;           // Acquisition period
        AdcRegs.ADCTRL1.bit.CPS = 0;              // ADC clock prescaler (divided by 1)
        AdcRegs.ADCTRL3.bit.ADCCLKPS = 9;         // ADC clock (SYSCLKDIV2)
    
        // Configure ADC sequencer
        AdcRegs.ADCMAXCONV.bit.MAX_CONV1 = 0;     // Set maximum sequence conversions to 0 (disabled)
    
        // Configure ADC channel (e.g., ADCINA0)
        AdcRegs.ADCCHSELSEQ1.bit.CONV00 = 0;      // Set conversion 0 to channel 0 (e.g., ADCINA0)
    
        // Start ADC conversions
        AdcRegs.ADCTRL1.bit.CONT_RUN = 1;
    }
    
    void InitSCI(void)
    {
        // Enable SCI clock
        CpuSysRegs.PCLKCR1.bit.SCIAENCLK = 1;
    
        // Reset SCI module
        SciaRegs.SCICCR.bit.SWRESET = 0;
    
        // Configure SCI module
        SciaRegs.SCICCR.all = 0x0007;            // 8-bit data, 1 stop bit, no parity, idle-line protocol
        SciaRegs.SCICTL1.all = 0x0003;           // Enable TX and RX
        SciaRegs.SCICTL2.all = 0x0003;           // Enable TX and RX interrupts
        SciaRegs.SCICTL2.bit.TXINTENA = 1;       // Enable TX interrupt
    
        // Configure SCI baud rate
        SciaRegs.SCIHBAUD = 0x00;                // Baud rate = LSPCLK / (SCIHBAUD * SCILBAUD)
        SciaRegs.SCILBAUD = 40;                  // Baud rate = 2e6 / (40 * 1) = 50000 bps
    
        // Start SCI module
        SciaRegs.SCICCR.bit.SWRESET = 1;
    }
    

    Please note that this code is just an example and may require modifications to fit your specific PMSM motor and hardware setup.

Responses were produced in different, uncontrolled contexts (system prompts, settings, prior turns). This is not a benchmark.