Skip to content
The Chat Archive
gpt-3.5-turbo-0613· OpenAI WildChat-4.8M (AI2)

你好

  1. User

    你好

  2. Assistant

    你好!有什么我可以帮助你的吗?

  3. User

    #include "stm32f10x.h" // Device header #include "usart.h" #include <string.h> #include <stdio.h> #include "misc.h" #include "stm32f10x_spi.h" #include "stm32f10x_tim.h" #include "ww_pwm.h" #include "ww_spi.h" #define SMG_CSL() (GPIOA->ODR &= ~(1<<4)) #define SMG_CSH() (GPIOA->ODR |= 1<<4) u8 Key_Val=0,Key_Up=0,Key_Down=0,Key_Old=0; u8 Key_SlowDown,SMG_SlowDown; u8 Usart_Send_Flag=0; u8 Motor_Fault_Flag,Led_Flag; u8 const DISP_TAB[] = { 0x3f,0x06,0x5b,0x4f,0x66,0x6d,0x7d,0x07,0x7f,0x6f,0x77,0x7c,0x39,0x5e,0x79,0x71,0x00}; u8 Led_Buf[]={0,0,0,0,0,0,0,0};//高电平点亮 volatile u8 Speed=0,Led_Pos=0; u8 Spaning_Mode,Draction_Mode;//旋转模式:0匀速旋转;1加速旋转;2减速旋转 旋转方向:1正向旋转;2反向旋转 volatile uint16_t SpeedUp_SlowDown_Delay; uint16_t SpeedUp_SlowDown_Con=200;volatile uint16_t Led_Compare=0; void Motor_Con(u8 Draction); void TIM2_IRQHandler(void) { TIM_ClearITPendingBit(TIM2, TIM_IT_Update); if(++Led_Compare>=(500-Speed*5)) { Led_Flag^=1; Led_Compare=0; } if(++Key_SlowDown==20)Key_SlowDown=0; if(++SMG_SlowDown==200)SMG_SlowDown=0; if(++Led_Pos==8)Led_Pos=0; if(Spaning_Mode==1 && ++SpeedUp_SlowDown_Delay%SpeedUp_SlowDown_Con==0) {

    	if(Speed<=90)
    		Speed+=5;
    	else
    	{
    		Speed=80;
    		Motor_Fault_Flag=1;
    		Spaning_Mode=0;
    	}
    	TIM1->CCR1=TIM1->CCR4=Speed;
    }
    else if(Spaning_Mode==2&& ++SpeedUp_SlowDown_Delay%SpeedUp_SlowDown_Con==0)
    {
    	if(Speed>=30)
    		Speed-=5;
    	else
    	{
    		Speed=25;
    		Spaning_Mode=0;
    	}
    	TIM1->CCR1=TIM1->CCR4=Speed;
    }
    //GPIO_WriteBit(GPIOC,GPIO_Pin_8,Bit_RESET);
    	//GPIO_Write(GPIOC,~(Led_Buf[Led_Pos]<<(8+Led_Pos)) & GPIO_ReadOutputData(GPIOC));
    

    }

    void Timer2_init(void) { TIM_TimeBaseInitTypeDef timerInitStructure; NVIC_InitTypeDef nvic; // 启用定时器2的时钟 RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM2, ENABLE);

    // 配置定时器2的预分频器和自动重载寄存器

    timerInitStructure.TIM_Prescaler = 71; // 预分频器值,实现 72MHz / (71 + 1) = 1MHz 的计数频率 timerInitStructure.TIM_CounterMode = TIM_CounterMode_Up; timerInitStructure.TIM_Period = 999; // 自动重载寄存器值,实现 1MHz / (999 + 1) = 1kHz 的中断频率 timerInitStructure.TIM_ClockDivision = TIM_CKD_DIV1; timerInitStructure.TIM_RepetitionCounter = 0; TIM_TimeBaseInit(TIM2, &timerInitStructure);

    // 配置定时器2的中断 TIM_ITConfig(TIM2, TIM_IT_Update, ENABLE);

    // 配置定时器2的中断优先级

    nvic.NVIC_IRQChannel = TIM2_IRQn; nvic.NVIC_IRQChannelPreemptionPriority = 0; nvic.NVIC_IRQChannelSubPriority = 0; nvic.NVIC_IRQChannelCmd = ENABLE; NVIC_Init(&nvic);

    // 启动定时器2 TIM_Cmd(TIM2, ENABLE); } //配置矢量中断,矢量的意思就是有顺序,有先后的意思。

    void SMG_Write(u8 Speed ) { SMG_CSL(); SPI1_ReadWrite(DISP_TAB[Speed%10]); if(Speed<10) { SPI1_ReadWrite(DISP_TAB[16]); SPI1_ReadWrite(DISP_TAB[16]); } else if(Speed<100&&Speed>9) { SPI1_ReadWrite(DISP_TAB[Speed/10%10]); SPI1_ReadWrite(DISP_TAB[16]); } else if(Speed>99) { SPI1_ReadWrite(DISP_TAB[Speed/10%10]); SPI1_ReadWrite(DISP_TAB[Speed/100%10]); } SPI1_ReadWrite(DISP_TAB[16]); SMG_CSH(); } void NVIC_Configuration(void) { NVIC_InitTypeDef NVIC_InitStructure; //定义数据结构体

    NVIC_SetVectorTable(NVIC_VectTab_FLASH, 0x0000);//将中断矢量放到Flash的0地址

    NVIC_PriorityGroupConfig(NVIC_PriorityGroup_1);//设置优先级配置的模式,详情请阅读原材料中的文章

    //使能串口中断,并设置优先级 NVIC_InitStructure.NVIC_IRQChannel = USART1_IRQn; NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 1; NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0; NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
    NVIC_Init(&NVIC_InitStructure); //将结构体丢到配置函数,即写入到对应寄存器中 } u8 Key_Read() { u8 Key=0,i; for(i=0;i<8;i++) {

    	if(!(GPIOC->IDR & (0x0001)<<i))
    	{
    		Key=i+1;
    	}
    	if(Key)break;
    }
    return Key;
    

    } void Key_Proc() { if(Key_SlowDown )return ; Key_SlowDown=1; Key_Val = Key_Read();//实时读取键码值 Key_Down = Key_Val & (Key_Old ^ Key_Val);//捕捉按键下降沿 Key_Up = ~Key_Val & (Key_Old ^ Key_Val);//捕捉按键上降沿 Key_Old = Key_Val;//辅助扫描变量 switch(Key_Down) { case 1: SpeedUp_SlowDown_Delay=0; if(Speed==0) Speed=25; Motor_Con(1); Spaning_Mode=1; TIM1->CCR1=TIM1->CCR4= Speed; printf("姓名;毕梦飞\t学号:202111200601\t当前模式:加速正转\t当前加速度:%d\r\n",(1000- SpeedUp_SlowDown_Con)/100+2); break; case 2: Spaning_Mode=0; if(Draction_Mode!=0) { Draction_Mode=3; printf("姓名;毕梦飞\t学号:202111200601\t当前模式:匀速正转\t当前加速度:0\r\n"); } break; case 3: SpeedUp_SlowDown_Delay=0; if(Speed==0) Speed=25; Motor_Con(1); Spaning_Mode=2; TIM1->CCR1=TIM1->CCR4= Speed; printf("姓名;毕梦飞\t学号:202111200601\t当前模式:减速正转\t当前加速度:%d\r\n",(1000- SpeedUp_SlowDown_Con)/100+2); break; case 4: SpeedUp_SlowDown_Delay=0; if(Speed==0) Speed =25; Motor_Con(2); Spaning_Mode=1; TIM1->CCR1= TIM1->CCR4=Speed; printf("姓名;毕梦飞\t学号:202111200601\t当前模式:加速反转\t当前加速度:%d\r\n",(1000- SpeedUp_SlowDown_Con)/100+2); break; case 5: SpeedUp_SlowDown_Delay=0; if(Speed==0) Speed=25; Motor_Con(2); Spaning_Mode=2; TIM1->CCR1= TIM1->CCR4=Speed; printf("姓名;毕梦飞\t学号:202111200601\t当前模式:减速反转\r\n当前加速度:%d\r\n",(1000- SpeedUp_SlowDown_Con)/100+2); break; case 6: Spaning_Mode=0; Speed=0; Motor_Con(0); Motor_Fault_Flag=0; Usart_Send_Flag=0; printf("停止旋转\r\n"); break; case 7: if(SpeedUp_SlowDown_Con<1000) SpeedUp_SlowDown_Con+=100; else SpeedUp_SlowDown_Con=1000; printf("当前加速度:%d",(1000- SpeedUp_SlowDown_Con)/100+2 ); break; case 8: if(SpeedUp_SlowDown_Con>200) SpeedUp_SlowDown_Con-=100; else SpeedUp_SlowDown_Con=200; printf("当前加速度:%d",(1000- SpeedUp_SlowDown_Con)/100+2 ); break; default:break; } } void SMG_Proc() { if(SMG_SlowDown)return; SMG_SlowDown=1; SMG_Write(Speed ); if(!Usart_Send_Flag&&Motor_Fault_Flag) { printf("转速过高,将调整转速为:80"); Usart_Send_Flag=1; } } void LED_Proc() { if(Draction_Mode==0) { GPIO_WriteBit(GPIOC,GPIO_Pin_8 | GPIO_Pin_9 | GPIO_Pin_10,Bit_SET); // GPIO_WriteBit(GPIOC,GPIO_Pin_9,Bit_SET); // GPIO_WriteBit(GPIOC,GPIO_Pin_10,Bit_SET); } else if(Draction_Mode==1) { GPIO_WriteBit(GPIOC,GPIO_Pin_8,Led_Flag? Bit_SET:Bit_RESET);; GPIO_WriteBit(GPIOC,GPIO_Pin_10 | GPIO_Pin_9,Bit_SET); } else if(Draction_Mode==2) { GPIO_WriteBit(GPIOC,GPIO_Pin_10,Led_Flag? Bit_SET:Bit_RESET);; GPIO_WriteBit(GPIOC,GPIO_Pin_8 | GPIO_Pin_9,Bit_SET); } else { GPIO_WriteBit(GPIOC,GPIO_Pin_9,Led_Flag? Bit_SET:Bit_RESET);; GPIO_WriteBit(GPIOC,GPIO_Pin_8 | GPIO_Pin_10,Bit_SET); } GPIO_WriteBit(GPIOC,GPIO_Pin_11,Motor_Fault_Flag?Bit_RESET:Bit_SET);

    } void Motor_Con(u8 Draction) {

    if(Draction ==0)//停止
    {
    	Draction_Mode=Draction;
    	GPIO_ResetBits(GPIOB , GPIO_Pin_0);
    }
    else if(Draction ==1 )//正转
    {
    	Draction_Mode=Draction;
    	PWM_GPIO_Configuration();
    	GPIO_SetBits(GPIOB , GPIO_Pin_0); //EN1=1;
    GPIO_ResetBits(GPIOA , GPIO_Pin_11);	//IN2=0; IN1有PA8 PWM控制
    }
    else if(Draction ==2)//反转
    {
    	Draction_Mode=Draction;
    	PWM_GPIO_Configuration();
    	GPIO_SetBits(GPIOB , GPIO_Pin_0); //EN1=1;
    GPIO_ResetBits(GPIOA , GPIO_Pin_8);	//IN1=0; IN2有PA11 PWM控制
    }
    	
    

    } void KeyLED_GPIO_Configuration(void) { GPIO_InitTypeDef GPIO_InitStructure;

    // 启用GPIOC的时钟 RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOC, ENABLE);

    // 配置PC0-PC7为上拉输入模式 GPIO_InitStructure.GPIO_Pin = GPIO_Pin_0 | GPIO_Pin_1 | GPIO_Pin_2 | GPIO_Pin_3 | GPIO_Pin_4 | GPIO_Pin_5 | GPIO_Pin_6 | GPIO_Pin_7; GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IPU; GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz; GPIO_Init(GPIOC, &GPIO_InitStructure);

    // 配置PC8-PC15为推挽输出模式 GPIO_InitStructure.GPIO_Pin = GPIO_Pin_8 | GPIO_Pin_9 | GPIO_Pin_10 | GPIO_Pin_11 | GPIO_Pin_12 | GPIO_Pin_13 | GPIO_Pin_14 | GPIO_Pin_15; GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP; GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz; GPIO_Init(GPIOC, &GPIO_InitStructure); }

    int main(void) { SystemInit(); KeyLED_GPIO_Configuration();

    PWM_GPIO_Configuration();
    usart_Configuration();
    PWM_TIM_Configuration();
    SPI_Configuration();
    SPI_GPIO_Configuration();
    //PWM_TIM_Configuration();
    //GPIO_SetBits(GPIOB , GPIO_Pin_0); //EN1=1;
    //GPIO_ResetBits(GPIOB , GPIO_Pin_1);	//IN2=0; IN1有PA8 PWM控制
    Timer2_init();
    GPIO_Write(GPIOC , (0xff00|GPIO_ReadInputData(GPIOC)));
    //SMG_Write(Speed );
    //SMG_Write(Speed );
    while(1)
    {
    	Key_Proc();
    	SMG_Proc();
    	LED_Proc();
    }
    

    }

    请在上述代码中添加代码,实现电机转速低于阈值时使D4灯自动熄灭

  4. Assistant

    在main函数中的LED_Proc()函数内添加以下代码:

    if(Speed < 30) {
        GPIO_WriteBit(GPIOC, GPIO_Pin_11, Bit_RESET); // D4灯熄灭
    }
    

    这段代码会在LED_Proc()函数中判断电机转速是否低于30,如果低于30,则将D4灯(GPIO_Pin_11)设置为低电平,即熄灭。

Responses were produced in different, uncontrolled contexts (system prompts, settings, prior turns). This is not a benchmark.