Skip to content
The Chat Archive
gpt-3.5-turbo-0301· OpenAI WildChat-4.8M (AI2)

"Air from the compressor cools the high-pressure turbine stage and the first three…

  1. User

    "Air from the compressor cools the high-pressure turbine stage and the first three low-pressure turbine stages utilizing a combination of film and convection cooling techniques. Cooling air for the hot gas path components is taken from four extraction points along the compressor. Air from two of these secondary air flows is used directly, while the two other streams are cooled by heat exchangers (once through coolers) before entering the hot gas path components. The heat rejected is recovered in the water-steam cycle, which maximizes the performance of the GT26 in combined-cycle applications. In simple-cycle applications, the cooling is achieved by quenching water, which is introduced directly into the secondary air stream." türkçe çevirisi

  2. Assistant

    "Kompresörden gelen hava, film ve konveksiyon soğutma tekniklerinin bir kombinasyonunu kullanarak yüksek basınçlı türbin aşamasını ve ilk üç düşük basınçlı türbin aşamasını soğutur. Sıcak gaz yol bileşenleri için soğutma hava, kompresörün dört çıkış noktasından alınır. Bu ikincil hava akımlarının ikisinden direkt olarak kullanılırken, diğer iki akım ısı değiştiricilerde (tek döngü soğutucuları) soğutulur ve daha sonra sıcak gaz yol bileşenlerine girer. Reddedilen ısı, GT26'nın birleşik çevrim uygulamalarındaki performansını maksimize etmek için su-buhar çevriminde geri kazanılır. Basit çevrim uygulamalarında, soğutma ikincil hava akışına doğrudan verilen soğuk su ile sağlanır."

  3. User

    "Aircraft-Derivative Gas Turbines Aero-derivatives are used in electrical power generation due to their ability to startup, shut down, and handle load changes more quickly than industrial machines. They are also used in the marine industry to reduce weight. The General Electric LM2500, General Electric LM6000, Rolls-Royce RB211, Rolls-Royce Avon, and the Pratt & Whitney FT-8 are common models of this type of machine. Aero-derivative gas turbines consist of two basic components: an aircraftderivative gas generator and a free-power turbine (Figure 1-34). The gas generator serves as a producer of gas energy; its job is to produce high-temperature gases at high pressure. The gas generator is derived from an aircraft engine modified to burn industrial fuels. Design innovations are usually incorporated to ensure the required long-life characteristics in the ground-based environment. In case of fan jet designs, the fan is removed and a couple of stages of compression are added in front of the existing low-pressure compressor. These additional stages are usually known as stage 00 and stage 0 thus keeping the stage numbering of the rest of the compressor stages the same as they were in the aircraft mode. The axial-flow compressor in most cases is divided into two sections – a low-pressure compressor followed by a high-pressure compressor. In those cases, there are usually a high-pressure turbine and a low-pressure turbine, which drive the corresponding sections of the compressor. The shafts are usually concentric thus the speeds of the high-pressure and low-pressure sections can be optimized. In these cases, the power turbine is separate and is not mechanically coupled; the only connection is via an aerodynamic coupling. The turbines have three shafts; the power turbine shaft is the drive shaft, all operate at independent speeds. The gas generator serves to raise combustion gas products to conditions of around 45–75 psi (3–5 Bar) and temperatures of 1300–1700 ◦F (704–927 ◦C) at the exhaust flange, that is entry to the power turbine. Figure 1-35 shows a cross section of the GE LM 6000 aero-derivative engine; it is most widely used in power production with an output of 48MW and an efficiency of 41% in the simple-cycle gas turbine mode. In its sprint mode, water is injected between the low- and high-pressure compressor sections as shown in Figure 1-36. In this engine, there are two compressor sections – a low-pressure and a high-pressure compressor sections – and three turbine sections – a high-pressure gas turbine section, which drives the high-pressure compressor, a lowpressure turbine, which drives through a coaxial shaft the low-pressure compressor section, and finally a power turbine, which drives the driven equipment such as generators, compressors, and pumps. The LM 6000 with a once through steam generator (OTSG) is widely used in combined-cycle applications especially in small areas, as the foot print of an OTSG is much smaller than a regular heat recovery steam generator (HRSG), as shown in Figure 1-37." türkçe çevirisi

  4. Assistant

    "Uçak Türevi Gaz Türbinleri Aero-türevleri, endüstriyel makinelerden daha hızlı başlatma, kapatma ve yük değişikliklerini işleyebilme kabiliyetleri nedeniyle elektrik enerjisi üretiminde kullanılır. Ayrıca, ağırlığı azaltmak için denizcilik endüstrisinde de kullanılmaktadır. General Electric LM2500, General Electric LM6000, Rolls-Royce RB211, Rolls-Royce Avon ve Pratt & Whitney FT-8 bu tür makinelerin yaygın modelleridir.

    Aero-türev gaz türbinleri iki temel bileşenden oluşur: bir uçak türevi gaz üreteci ve bir serbest güç türbini (Şekil 1-34). Gaz üreteci, gaz enerjisi üreticisi olarak hizmet eder ve görevi yüksek basınçta yüksek sıcaklıklarda gazlar üretmektir. Gaz üreteci, sanayi yakıtlarını yakmak için modifiye edilmiş bir uçak motorundan türetilir. Gerekli uzun ömürlü özellikleri yer tabanlı ortamda sağlamak için tasarım yenilikleri genellikle dahil edilir. Vantilatör jeti tasarımlarında, vantilatör çıkarılır ve mevcut düşük basınçlı kompresörün önüne birkaç aşama sıkıştırma eklenir. Bu ek aşamalar genellikle 00 ve 0 aşamaları olarak bilinir, böylece kompresörün geri kalan aşama numaralandırması uçak modundaki numaralandırmalarıyla aynı kalır. Çoğu durumda aksiyel akışlı kompresör, bir düşük basınçlı kısım ve bir yüksek basınçlı kısım olarak iki bölüme ayrılır. Bu durumlarda genellikle yüksek basınçlı bir türbin ve düşük basınçlı bir türbin vardır ve bunlar ilgili kompresör kısımlarını hareket ettirir. Şaftlar genellikle konsantrik olup, yüksek basınç ve düşük basınçlı bölümlerin hızları optimize edilebilir. Bu durumlarda, güç türbini ayrıdır ve mekanik olarak bağlı değildir; tek bağlantı aerodinamik bir bağlantı yoluyla sağlanır. Türbinler üç şafta sahiptir; güç türbin şaftı sürücü şaftıdır ve hepsi bağımsız hızlarda çalışır.

    Gaz üretecinin görevi, yaklaşık 45-75 psi (3-5 Bar) koşullarına ve egzoz flanşı girişinde 1300-1700 ◦F (704-927 ◦C) sıcaklıklara yükseltmek için yanma gazı ürünleridir. Şekil 1-35, GE LM 6000 aero-türevli motorunun bir kesitini gösterir; basit çevrim gaz türbin modunda 48MW çıkışı ve %41 verimliliği ile genellikle güç üretiminde en yaygın olarak kullanılır. Koşu modunda, Şekil 1-36'da gösterildiği gibi düşük ve yüksek basınçlı kompresör bölümleri arasına su enjekte edilir. Bu motorda, bir düşük basınçlı ve bir yüksek basınçlı kompresör bölümü olmak üzere iki kompresör bölümü ve bir yüksek basınçlı gaz türbini bölümü, yüksek basınçlı kompresörü tahrik eden bir düşük basınçlı türbin, düşük basınçlı kompresör bölümünü koaksiyel bir şaftla tahrik eden bir güç türbini bulunmaktadır. LM 6000, bir kez kullanılan buhar jeneratörlü (OTSG) geniş çevrim uygulamalarında özellikle küçük alanlarda yaygın olarak kullanılır, çünkü bir OTSG'nin yer kaplaması, düzenli bir ısı geri kazanım buhar jeneratöründen (HRSG) çok daha küçüktür, Şekil 1-37'de gösterildiği gibi."

  5. User

    "The Rolls-Royce Aero-derivative Gas Turbines, the Avon and the RB-211, are widely used. The Rolls’ Avon is used in compression gas pipelines stations, and the RB 211-HB3 with an output of about 42.4MW and an efficiency of 39.3% is used in power generation. Figure 1-38 is a cross-section of the RB 211. The RB 211 has a two-stage power turbine as shown in Figure 1-39. These types of power turbines are built by many compressor manufacturers such as Dresser-Rand and Cooper-Bessemer (now Cameron Industries) to power their compressors and also for power production. The FT8 aero-derivative gas turbine made by Pratt & Whitney is in the 25-MW class and is used in industrial and municipal power supplies. The FT8 TwinPac unit offers 52MW of electrical power from a two-engine single-generator configuration. The twin pack is a unit driving a single generator from both the ends. The FT8 gas turbine is based on aero-engine technology from Pratt & Whitney, adapted for industrial use as seen in Figure 1-40. The gas turbine is characterized by a compact and modular design. The PowerPac and the TwinPac offer two different variants of the FT8 gas turbine for power generation purposes. To drive compressors MechPac, the power turbine developed by MAN Diesel & Turbo is used. This has a rated speed of 5,500 rpm. Pollutant emissions are reduced by means of dry-low-NOx-Brennkammer or by injecting water into the fuel chamber of the turbine. Typical applications include pipeline compressor units and gas treatment plant compressors. Both the power and the petrochemical industries use the aircraft-type turbine. The power industry uses these units in a combined-cycle mode for power generation especially in remote areas where the power requirements are less than 100MW. The petrochemical industry uses these types of turbines on offshore platforms especially for gas reinjection and as power plants for these offshore platforms, mostly due to their compactness and the ability to be easily replaced and then sent out to be repaired. The aero-derivative gas turbine is also used widely by gas transmission companies and petrochemical plants, especially for many variable speed mechanical drives. These turbines are also used as main drives for destroyers and cruise ships. The benefits of the aeroderivative gas turbines are as follows:

    1. Favorable installation cost. The equipment involved is of a size and weight that it can be packaged and tested as a complete unit within the manufacturer’s plant. Generally, the package will include either a generator or a driven pipeline compressor and all auxiliaries and control panels specified by the user. Immediate installation at the job site is facilitated by factory matching and debugging.
    2. Adaptation to remote control. Users strive to reduce operating costs by automation of their systems. Nowadays, many new offshore and pipeline applications are designed for the remote unattended operation of the compression equipment. Jet gas turbine equipment lends itself to automatic control, as auxiliary systems are not complex, water cooling is not required (cooling by oil-to-air exchanges), and the starting device (gas expansion motor) requires little energy and is reliable. Safety devices and instrumentation adapt readily for the purposes of remote control and monitoring the performance of equipment.
    3. Maintenance concept. The offsite maintenance plan fits in well with these systems where minimum operating personnel and unattended stations are the objectives. Technicians conduct minor running adjustments and perform instrument calibrations. Otherwise, the aeroderivative gas turbine runs without inspection until monitoring equipment indicates distress or sudden performance change. This plan calls for the removal of the gasifier section (the aero-engine) and sending it back to the factory for repair while another unit is installed. The power turbine does not usually have problems since its inlet temperature is much lower. Downtime due to the removal and replacement of the gasifier turbine is about eight hours." türkçe çevirisi
  6. Assistant

    "Rolls-Royce Aero-Türevli Gaz Türbinleri, Avon ve RB-211, yaygın olarak kullanılmaktadır. Rolls’ün Avon’u sıkıştırma gaz boru hatları istasyonlarında kullanılırken, RB 211-HB3 42,4MW çıkışı ve %39,3 verimliliği ile güç üretiminde kullanılmaktadır. Şekil 1-38, RB 211'in bir kesitidir. RB 211, Şekil 1-39'da gösterildiği gibi iki aşamalı bir güç türbinine sahiptir. Bu tür güç türbinleri, Dresser-Rand ve Cooper-Bessemer gibi birçok kompresör üreticisi tarafından kompresörlerini ve güç üretimi için de yapılmaktadır. Pratt & Whitney tarafından yapılan FT8 aero-türevli gaz türbini 25-MW sınıfındadır ve endüstriyel ve belediye enerji kaynaklarında kullanılmaktadır. FT8 TwinPac ünitesi, iki motor tek bir jeneratör konfigürasyonundan 52MW'lık elektrik gücü sağlar. Twin paket, her iki ucundan da tek bir jeneratörü çalıştıran bir ünitedir. FT8 gaz türbini, Pratt & Whitney tarafından uçak motoru teknolojisine dayalı olarak tasarlanmış ve endüstriyel kullanım için uyarlanmıştır. Şekil 1-40'ta görülebileceği gibi gaz türbini, kompakt ve modüler bir tasarıma sahiptir. PowerPac ve TwinPac, güç üretimi amaçları için FT8 gaz türbininin iki farklı farklı varyasyonunu sunar. Kompresörleri tahrik etmek için MAN Diesel & Turbo tarafından geliştirilen MechPac kullanılmaktadır. Bu, 5.500 rpm nominal hıza sahiptir. Kirlilik emisyonları, kuru-düşük-NOx-Brennkammer yoluyla veya türbinin yakıt odasına su enjekte edilerek azaltılır. Tipik uygulamalar arasında boru hatı kompresör üniteleri ve gaz işleme tesisi kompresörleri yer alır. Hem güç hem de petrokimya endüstrisi uçak tipi türbinleri kullanır. Güç endüstrisi, güç gereksinimlerinin 100MW'den az olduğu özellikle uzak bölgelerde güç üretimi için bu üniteleri birleşik çevrim modunda kullanır. Petrokimya endüstrisi, özellikle gaz yeniden enjeksiyonu için açık deniz platformlarında bu tür türbinleri kompaktlığı ve kolayca değiştirilebilir olmaları nedeniyle kullanır ve ardından tamir için geri gönderirler. Aero-türevli gaz türbini ayrıca gaz iletim şirketleri ve petrokimya tesisleri tarafından, özellikle birçok değişken hızlı mekanik tahrik için yaygın olarak kullanılmaktadır. Bu türbinler, muhrip ve kruvazörler için ana tahrikler olarak da kullanılır. Aero-türevli gaz türbinlerinin faydaları şunlardır:

    1. Uygun kurulum maliyeti. İlgili ekipman, üretim tesisinde tamamlanan birim olarak paketlenebilir ve test edilebilir boyut ve ağırlıktadır. Genellikle, paket, kullanıcı tarafından belirtilen bir jeneratör veya tahrik edilen boru hattı kompresörü ve tüm yardımcılar ve kontrol panolarını