Skip to content
TheChatArchiveThe Chat Archive
gpt-3.5-turbo-0301· OpenAIAi2 WildChat-4.8M (AI2)

This app provides you full access to GPT-3.5 (4096 token limit). You don't need any…

  1. User

    This app provides you full access to GPT-3.5 (4096 token limit). You don't need any OPENAI API key. Chatbot Even if the copper sample has been treated with amidosulfonic acid to remove residual surface oxides before exposure, the surface is nevertheless covered by a thin hydroxylated cuprous oxide layer under ambient conditions [34]. This is schematically illustrated in Fig. 8a) atthe beginning of the exposure, marked with native Cu2O, and no other corrosion products yet formed. The active species in the exposure chamber result in an aqueous adlayer consisting of some monolayers of water molecules on the surface, which acts as an ultrathin electrolyte for further electrochemical reactions. For clarity reasons, this adlayer is not shown in the forthcoming illustrations of Fig. 8. Upon exposure and the incorporation and dissociation of formic acid into the adlayer, two different dissolution mechanisms of the Cu2O-layer have previously been identified, both experimentally and computationally: a ligand- and a proton- promoted dissolution process, both of which result in more general or more local dissolution of parts of the Cu2O-layer [5]. Because of the solid-state growth of the Cu2O layer during exposure, as seen in Fig. 1 and studied more in detail elsewhere [31], the result is a thickened oxide layer exhibiting increased surface topography, depicted in Fig. 8b). From the detailed analysis of, e.g. Fig. 5g) and Fig. 7f), one can discern that the formation of Cu(OH)(HCOO) seems to follow two different reaction routes. The first route consists of partial dissolution of Cu2O over larger parts of the oxide surface and concomitant release of Cu+ ions which immediately oxidise to Cu2+ to form Cu(OH)(HCOO) together with dissolved HCOO- and OH- ions, depicted in Fig. 8c). The second reaction route to form Cu(OH)(HCOO) is considered next. As shown in the cross-section displayed in Fig. 7f), local parts of the Cu2O-layer will be eventually completely dissolved, allowing the aqueous adlayer to be in direct contact with the copper substrate, depicted in Fig. 8c). The exposure of the bare copper substrate and the higher nobility of Cu2O compared to Cu [4] triggers the electrochemical reactions and the formation of a corrosion cell: Anodic reaction: Cu → Cu+ + e- (1) Cathodic reaction: O2 + 4e- + 2 H2O → 4OH- (2) An immediate implication of these reactions is the formation of Cu2O over parts of the surface, as seen in several of the images in Fig. 3, Fig. 5, and Fig. 7, according to: 2Cu+ + 2OH- → Cu2O + H2O (3) In Fig. 5e) for the 48 h sample and Fig. 7f) for the 72 h sample, shown with a dashed yellow rectangle, one can discern further growth of Cu2O next to the Cu(OH)(HCOO) region, suggesting that Cu2O has been formed as a result of the cathodic reaction. The fact that the overall layer thickness of Cu2O eventually reached an approximately constant thickness according to the IRRAS results shown in Fig. 1, suggests that both the dissolution and formation of Cu2O take place so that an overall steady-state thickness was reached after 24 h or more. A conclusion from the GILDES calculations [31] is the immediate oxidation of released Cu+ to Cu2+ because of the oxidative conditions in the current atmospheric environment. The end reaction product found, besides Cu2O, is Cu(OH)(HCOO) which previously has been identified in laboratory exposures [35]. In the presence of released Cu2+ and OH- and dissolved HCOO-, the conditions are favourable to form Cu(OH)(HCOO) at local areas adjacent to areas where the Cu2O-layer has been dissolved locally, with the following overall reaction: Overall reaction: Cu2+ + OH- + HCOO- → Cu(OH)(HCOO) (4) Findings from the current study regarding the local formation of Cu2O and of Cu(OH)(HCOO) have been schematically illustrated in Fig. 8d). Route 2 in this figure forms evidence of a corrosion cell. This is supported by the local formation of Cu(OH)(HCOO) at the anodic site (including reactions 1 and 4) and nearby local formation of Cu2O at the cathodic site (reactions 2 and 3). The fact that extremely confined areas of copper formate can be seen in Fig. 6 may support the conclusion that corrosion cells have been formed at many parts of the corroding copper surface.

  2. Assistant

    This passage describes the corrosion of copper under exposure to formic acid. Despite treatment with amidosulfonic acid, the surface of the copper is covered in a thin layer of hydroxylated cuprous oxide. Exposure to formic acid leads to the dissolution of parts of the Cu2O layer through ligand- and proton-promoted processes. This results in a thickening of the Cu2O layer and increased surface topography. Two different reaction routes are observed in the formation of Cu(OH)(HCOO), one with partial dissolution of Cu2O over larger parts of the oxide surface and the other through local dissolution of parts of the Cu2O layer allowing direct contact of the aqueous adlayer with the copper substrate.

    Electrochemical reactions occur due to the exposure of the bare copper substrate and the higher nobility of Cu2O compared to Cu. This leads to the formation of a corrosion cell with an anodic reaction releasing Cu+ ions that oxidize to Cu2+, and a cathodic reaction involving O2 and H2O that form OH- ions. This results in the formation of Cu2O over parts of the surface due to the reaction between Cu+ and OH- ions. The overall layer thickness of Cu2O reaches a steady-state thickness after 24 hours or more due to the dissolution and formation of Cu2O.

    The GILDES calculations suggest the immediate oxidation of released Cu+ to Cu2+. The end reaction products formed are Cu2O and Cu(OH)(HCOO). Findings from the study suggest that corrosion cells have formed in many parts of the corroding copper surface due to the local formation of Cu(OH)(HCOO) at the anodic site and nearby local formation of Cu2O at the cathodic site. Extremely confined areas of copper formate also support the conclusion that corrosion cells have formed.