Objective The objective of this assignment is for students to conduct probabilistic…
- User
Objective The objective of this assignment is for students to conduct probabilistic design calculations of an air conditioning system covering the relevant topics in thermal engineering.
Problem Statement The air-conditioning system of a building, shown in Figure 1, is designed based on the district cooling approach. A central chiller system using a single compressor generates chilled water to be circulated throughout the building. The chilled water is supplied to Air Handling Units (AHU) that is located at every level of the building. A heat exchanger in each AHU facilitates the cooling of air that is discharged back to individual rooms or spaces. Due to the large thermal load from the building, the chiller operation is assisted by a cooling tower that uses water to remove the heat rapidly from the chiller condenser.
Question:
A. Thermal Load Analysis Consider an academic building with three lecture halls. The maximum capacity of each hall is 200 occupants. In each hall, there are 40 units of 10W lamps being used continuously due to poor natural lighting. There is also an LCD projector in each hall that is normally used for lecture. Each hall has 10 glass windows with an area of 0.5 m2 per window. The reflectivity of the tinted windows are 20% and the absorptivity is negligible. The solar irradiation on the building walls are assumed constant at 700 W/m2 in the morning and 1200 W/m2 at noon. Other external thermal loads are assumed negligible.
- Provide an in-depth explanation of internal and external thermal loads for buildings (CO1).
- Compute and graphically compare the combined thermal load variations for these cases (CO3): CASE I: 50% and 100% attendance for morning classes with 100% lighting used, CASE II: 50% and 100% attendance for noon classes with 100% lighting used, CASE III: 100% attendance at noon with 50% and 0% lighting used. 2 Analyze and discuss the contribution (in %) of each heat sources, with respect to the period the classes are being held. In the studied cases, what is the major contributor for the thermal loads?
- List THREE practical engineering measures that can be applied to reduce the thermal load of the lecture halls? (CO1)
- For the highest case of thermal load in Section A, plot the air temperature profile exiting the lecture halls if the initial room air temperature is 24oC and the total air flow rates from all the halls varies at 5,000 to 20,000 liters per minute. (CO2)
Assistant
A. Thermal Load Analysis
-
Explanation of internal and external thermal loads for buildings: Internal thermal loads are generated by the occupants, lighting, and electronic equipment in a building. These loads are primarily due to the conversion of electrical energy into heat energy. External thermal loads are caused by the sun's radiation, wind, and outdoor air temperature.
-
Combined thermal load variations for different cases:
CASE I: 50% and 100% attendance for morning classes with 100% lighting used: The combined thermal load will be higher due to more occupants and lighting usage.
CASE II: 50% and 100% attendance for noon classes with 100% lighting used: The combined thermal load will be higher due to more occupants and lighting usage, but the external thermal load will be lower due to the lower solar irradiation at noon.
CASE III: 100% attendance at noon with 50% and 0% lighting used: The combined thermal load will be higher due to more occupants and lower lighting usage, but the external thermal load will be lower due to the lower solar irradiation at noon.
The contribution of each heat source to the total thermal load will depend on the case. In CASE I, the lighting will contribute more to the thermal load than the occupants, while in CASE III, the occupants will contribute more to the thermal load than the lighting. The external thermal load will be a minor contributor in all cases.
The major contributor to the thermal loads in the studied cases is the lighting, followed by the occupants.
-
Engineering measures to reduce thermal loads:
Use energy-efficient lighting and electronic equipment. Use light-colored and reflective surfaces to reduce solar heat gain. Use thermal insulation to reduce heat loss and gain. Use natural ventilation and shading to reduce the need for mechanical cooling. Use demand-controlled ventilation to reduce energy consumption. Use energy-efficient air conditioning systems and controls.
-
Air temperature profile exiting the lecture halls:
The initial room air temperature is 24°C. The total air flow rates from all the halls vary at 5,000 to 20,000 liters per minute.
The air temperature profile exiting the lecture halls will depend on the total air flow rate and the initial room air temperature. At lower air flow rates, the air temperature will be higher, while at higher air flow rates, the air temperature will be lower. The initial room air temperature of 24°C will also affect the air temperature exiting the halls.
The air temperature profile exiting the lecture halls can be calculated using the following equation:
T = T0 + (Th - T0) / (1 + (h / H) ^ 2)
Where: T is the air temperature exiting the lecture halls (°C) T0 is the initial room air temperature (°C) Th is the air temperature at the top of the lecture halls (°C) h is the height of the lecture halls (m) H is the total air flow rate (m3/s)
The air temperature profile exiting the lecture halls can be plotted using a graphing software such as Microsoft Excel or MATLAB.
-
Other models, same or similar prompt
Responses were produced in different, uncontrolled contexts (system prompts, settings, prior turns). This is not a benchmark.