Skip to content
TheChatArchiveThe Chat Archive
Qwenqwen1.5-72b-chat· Alibaba (Qwen)Hugging Face Arena Human Preference 55K

Which one of these passages looks better? Passage 1 or Passage 2? Which one is more…

From a Chatbot Arena battleThe same person sent this prompt to two anonymous models at once. Compare it with Mistralmixtral-8x7b-instruct-v0.1’s answer.
  1. User

    Which one of these passages looks better? Passage 1 or Passage 2? Which one is more meticulous enough, making it a better contender to be in a lab report? Explain.

    Passage 1

    To start the procedure, a conductivity probe had its sensitivity set down to the range of 0 to 2000 µS, and it was plugged into the LabQuest through the conductivity probe’s wire. On the LabQuest, the mode was switched from time-based to events with entry, and the unit was changed to drops. Due to the wash bottle not having enough distilled water in it, more distilled water was put into it until it filled half of the bottle. The 50.0 mL beaker and conductivity probe were rinsed with this distilled water over a bucket to safely and conveniently collect the contaminated water. Then, exactly 40.0 mL of distilled water was measured in a graduated cylinder on a flat surface, and the water was stopped from pouring when the water’s meniscus reached the 40.0 mL mark. Then, with no compounds put into the water, the play button on the LabQuest was pressed, and the conductivity probe was swirled until the conductivity calmed down. The conductivity probe was held while the metal part was in the water to prevent the beaker and it from falling, and the keep button was pressed for zero drops after the conductivity remained constant. Next, the probe was taken out of the distilled water and held as the first drop of aqueous ethanol (CH3CH2OH) from a vial was put in using an eyedropper. The conductivity probe was reinserted into the water after a couple of seconds of waiting and swirled until the conductivity did not change drastically. The conductivity probe was again held in the water so that the beaker would not fall, and the keep button for one drop was pressed when the conductivity remained constant. The conductivity probe was taken out and held out in the air after the measurement was recorded. This process from taking out the conductivity probe to the conductivity being recorded was repeated seven more times, which resulted in nine different measurements with eight of them having drops of ethanol. After recording all of the measurements for the ethanol, the stop button on the LabQuest was pressed and the ethanol and water solution was dumped into the bucket. Both the 50.0 mL beaker and the metal part of the conductivity probe were also rinsed with the distilled water from the wash bottle. From there, another vial containing aqueous NaCl was used to conduct the same steps that were done for the aqueous ethanol from recording the conductivity from there being no drops of water to rinsing the metal part of the conductivity probe and the beaker with distilled water from the wash bottle except with a different eyedropper. This procedure, also with a different eyedropper, was repeated for aqueous CaCl2 from measuring the conductivity of no drops to cleaning the beaker and the metal part of the conductivity probe for less contamination in the future. The LabQuest was then connected to two iPads via a Wi-Fi connection and the data recorded from these three aqueous compounds was finally saved to the iPads.

    Passage 2

    To start this lab the LabQuest was connected to an electrical outlet and turned on. The box attached to the conductivity probe had a toggle button set to its lowest setting of 0-2000µS. The probe was then connected to the LabQuest, and the mode of the LabQuest was changed from time-based to events with entry, the name of the title was changed from event to concentration and the unit was switched to drops. After the LabQuest was set up, a 50.0mL beaker and the silver portion of the conductivity probe were thoroughly cleaned using a wash bottle filled with distilled water to prevent contamination. Then, using a graduated cylinder, 40.0mL distilled water was measured out and poured into the just-cleaned 50.0mL beaker. With the 40.0mL of distilled water ready, the play button was pressed on the LabQuest, and the conductivity probe was inserted into the beaker containing the sample. The probe was swirled until the water conductivity calmed down, and when the readings on the LabQuest stopped fluctuating, the keep button was pressed, finishing this trial. This data was labeled as the base as there were 0 drops of concentration added to the beaker. The probe was then taken out to prevent the sample from spilling. After the base was recorded, a liquid compound (ethanol) was selected and was methodically added to the base sample. This was done by using a dropper, as a drop of the liquid compound would be added to the sample, and the conductivity probe was stirred until the conductivity remained stable, which made the keep button pressed. The process of adding a drop was repeated eight times, with one drop being added every time and kept until 8 drops were done, and then the stop button was pressed. The steps from cleaning the beaker and the probe to adding the 8 drops were repeated twice more for the other two compounds (sodium chloride and calcium chloride).

  2. Qwen Assistant

    Both passages describe a lab procedure for measuring the conductivity of aqueous solutions with the addition of different compounds. However, Passage 1 is more meticulous in its details, making it a better fit for a lab report. Here's why:

    1. Specificity and clarity: Passage 1 provides more specific details, such as the exact volume of distilled water added to the wash bottle, the use of a flat surface for measuring the water, and the waiting time before reinserting the probe. These details are important for replication of the experiment.
    2. Step-by-step instructions: Passage 1 breaks down the process more thoroughly, explaining each step in a logical sequence. It is clearer about actions like swirling the probe and holding it to prevent the beaker from falling, which are critical for obtaining accurate readings.
    3. Equipment and safety: Passage 1 mentions the use of a bucket to collect contaminated water, emphasizing safety and proper disposal. It also specifies that different eyedroppers were used for different compounds, reducing cross-contamination.
    4. Data recording and management: Passage 1 explains how the data was recorded and saved on the iPads, providing information on the post-experiment process.

    Passage 2, while concise, omits some important details and is less descriptive in its instructions, which could make it less suitable for a formal lab report where accuracy and reproducibility are crucial.

Responses were produced in different, uncontrolled contexts (system prompts, settings, prior turns). This is not a benchmark.